Zenith - Philips VR1010BP Owner's Manual

52Setting t heController to Operate a Cable Box (cont'd)
6
Press the PLAY • or STOP V button to set the code for
your Cable Box (see list below), then press the OK/STA-
TUS button. (Single digits will appear on the screen for
codes 01-09,)
S s_c_ coD_NU_E_
OF YOUR CABLE BOX
!
D_D CABL£ BOX DISPLA'€
C_ANGE TO CHANNEL 09!
?
,w.YES
NO
SELECT &"l/ CONFIP, M OK
D MENU
CABLE BOX CODES
ARCHER ......... 01,0S, 17
CABLETENNA ....... 0 I, 17
CABLEVIEW .15, 16, 17,21,25
C_TIZEN
.... iS, 16, 17, 21,25
CURTIS ............. 02, 08
D_AMOND .......... 0 I, 17
EASTERN .............. 19
GC BRAND .15, 16, 17,21,25
GEMINI ............... 15
GENERAL INSTRUMENTS
........ 01,04.06, II, 12, 15
HAMLIN ...... 10, 18. 19,23
JASCO ................ IS
JERROLD
........ 01,04,06, _i, 12, iS
N OVAVISION ........ 02, 08
OAK ............... 07, 20
PANASONIC ........ 13, 14
PULSAR .... 15, 16, 17,21,25
RCA ............... 13, 14
REGAL ........ 10, 18, 19,23
REGENCY ............. 19
REMBRANDT ..... 01, 16, 17
SAMSUNG ....... 0S, 16, 24
SCIENTIFIC ATLANTA .02, 08
SIGMA ............. 07, 20
SLMARX ,..05,16,17,24,25
SPRUCER ........... 13, 14
STARGATE .... 05, 15, 16, 17,
................ 21,24,25
TELEVIEW ........ 05, 16, 24
TOCOM ......... 01,04, 16
UNIKA ............. 01. 17
UNIVERSAL ....... 16, 17, 25
VIDEOWAY ....... 03, 09, 22
ZENITH ......... 03, 09, 22
7
Wait for a few seconds,
• If the Cable Box changesto channel 09, go to step 8.
• If the Cable Box doesn't change to channel 09, press the PLAY
• or STOP • button to select NO, then press the OK/STATUS
button. Repeat steps 6-7 using a different code for your brand, if
available.
• If the Cable Box does not respond to any of the codes,press
the MENU button to remove the menu. CABLE BOX CON-
TROL IS OFF will appear on the screen briefly.
8
Press the PLAY • or STOP • button to selectYES, then
press the OK/STATUS button. "CABLE BOX CONTROL IS
ON" will appear for five seconds."AS A RESULTAUTO CLOCK
WILL BETURNED OFF" also may appear on the screen.
Helpful Hints
i i
If your Cable Box does not respond
to any of the codes at step 7, the
Controller will not change channels
at the Cable Box during a timer
recording.You must select the chan-
nel to be recorded at the Cable Box
before a timer recording begins.
Enter the Cable Box output channel
at step 3 on page 40. Leave the
Cable Box on for the timer record-
ing. See page eight for details.
You may want to exchange your cur-
rent Cable Box for one that can be
controlled by the VCR'sCentreller.
The Controller can change channels
at the Cable Box only during a timer
recording.