Table of Contents
Advertisement
WARM AIR FURNACE
MULTIPOSITION
1
. ,_
:: , _
i_
J
J
J
J
INSTALLER / SERVICE TECHNICIAN:
USE
THE
INFORMATION
IN
THIS
MANUAL
FOR
THE
INSTALLATION
/ SERVICING
OF THE FURNACE
AND KEEP
THE DOCUMENT NEAR THE UNIT FOR FUTURE REFERENCE.
HOMEOWNER:
PLEASE
KEEP
THIS
MANUAL
NEAR
THE
FURNACE
FOR
FUTURE REFERENCE.
Printed in Canada
Printed on 100% recycled paper
2009-02-10
Models:
AMP105-1E2
AMP120-1E2
NOMF105D12C
NOMF155E19C
NOMF106D12B
NOMF156E19C
®
C
US
Attention:
Do not tamper with the unit or its
controls.
Call a qualified service technician.
Manufactured
by:
UTC Canada Corporation
ICP Division
3400 Industrial Boulevard
Sherbrooke,
Quebec - Canada
J1L 1V8
X40002 Rev. Q
445 01 4094 04
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ICP AMP105-1E2
Summary of Contents for ICP AMP105-1E2
- Page 1 Call a qualified service technician. INSTALLATION / SERVICING OF THE FURNACE AND KEEP THE DOCUMENT NEAR THE UNIT FOR FUTURE REFERENCE. Manufactured UTC Canada Corporation HOMEOWNER: ICP Division 3400 Industrial Boulevard PLEASE KEEP THIS MANUAL NEAR FURNACE Sherbrooke, Quebec - Canada FUTURE REFERENCE.
-
Page 2: Part 1 Installation
PART 1 INSTALLATION FOR YOUR SAFETY CAUTION STORE GASOLINE OTHER These instructions intended FLAMMABLE VAPOURS AND LIQUIDS IN THE VICINITY qualified personnel having been trained OF THIS OR ANY OTHER APPLIANCE installing this type of furnace. Installation of this furnace by an unqualified person lead to... - Page 3 The furnace is shipped complete with burner and controls. It requires a 115VAC line voltage connection to the control panel, thermostat hook-up as shown on the wiring diagram, one or more oil line connections, suitable ductwork connection to a properly sized vent. The air handling capacity of this furnace...
- Page 4 Return air grilles warm air registers must not be CAUTION obstructed. Do not block the combustion air openings furnace. blockage will result IMPORTANT: The dampers should be adequate improper combustion and may result in a fire prevent cooled air from entering the furnace, and if hazard and/or cause...
- Page 5 If the furnace is vented into a common chimney, the chimney parallel airflow installation, dampers must must be of sufficient area to accommodate the total flue provided to direct air over the furnace heat exchanger products of all appliances vented into the chimney. when heat is desired and over the cooling coil when The following requirements are provided for a safe venting...
- Page 6 FIGURE 1 Blocked Vent Shut-Off device wiring Installation shown: Upflow with vertical exhaust The position of the I_ _N Blocked Vent Shut-Off hole in the vent is IU_:_:'_ device BVSO. subject to the length Electrical kit supplied. of the electrical kit. Use the three wire fasteners.
- Page 7 FIGURE 5 FIGURE 4 Blocked Vent Shut-Off device wiring Blocked Vent Shut-Off device wiring. Installation: Horizontal with vertical exhaust Installation: Horizontal with horizontal exhaust DNS-1043 Rev, DNS-1043 Rev. A2 FIGURE 6 Blocked Vent Shut-Off device wiring Installation: Downflow 99 o °0 O DNSN 043 Rev, A2 445 01 4094 04...
- Page 8 When installing optional accessories to this appliance, follow 1.3.6 Venting instructions the manufacturer's installation instructions included with the (Sealed Combustion Systems) accessory. Other than wiring for the thermostat, wire with a Please refer to the Sealed Combustion System or Direct minimum of type "T"...
-
Page 9: Part 2 Start-Up
On counterftow Installations, the flue pipe must exit the I MPORTANT: The burner must always be installed in the upright position with the ignition control on top. cabinet through one of the side panel openings above), then extended up the side of the furnace. Ensure that adequate clearances to combustibles... -
Page 10: Supply Air Adjustments
Open the burner air shutter to get 1.5% less Blower Speed Adjustments than the previous reading noted in b. above and (4 Speed Motors, Cooling Mode) take a smoke test on this condition; FURNACE COOLING RECOMMENDED The new smoke reading should give you a ZERO MODEL CAPACITY BLOWER SPEED... -
Page 11: Part 3 Maintenance
CONSTANT BLOWER SWITCH HEATING This furnace is equipped with a constant low speed blower The blower speed is factory set to deliver the required airflow option. Whenever the room thermostat is not calling for at normal duct static pressure, heating or cooling, the blower will run on low speed in order to provide air circulation. -
Page 12: Part 4 Furnace Information
Remove the two screws holding the control box to the Clean and remove any build-up or obstruction inside the heat transfer tube assembly. Sliding the control box in the heat transfer tube; appropriate direction will unlock it from the heat transfer Re-mount, lock and fasten the control box with the 2 tube assembly;... - Page 13 TABLE 3 Technical Specifications IVbdel: AIVP & NOMF 105 / 106 120 / 155 / 156 i o i i lOO Input (BTU/h)* 70,000 91,000 105,000 119,000 140,000 154,000 Firing rate (USGPH)* 1.10 Heating capacity (BTU/h)* 57,000 74,000 85,000 97,000 115,000 126,000 13 - 29°C (55 - 85°F)
- Page 14 FIGURE 7.1 Models : AMP & NOMF 105/106 /--\ is s I Ri 'ONCA {C/_Q COIl{S) .%StJS/ O _ "_PO(JR TUY,_U 5"/ KNOCKOUT BOIH SIDES 5" DIAL4 "J_4 E:\ IRE DEF ONCAB E POJR INiEi ¸ (B(}TI_ SIDES) i I('NE A L'i4d_LE: {{'iiAQUiii C0iES)/...
- Page 15 FIGURE 7.2 Models: AMP & NOMF 120 / 155/156 iN[RL D I ONCABi (CI!AOtJE CO[ES) POUR TUY/_tJ 6"/ KNOCKOUT BOTJ; BIDES 6" ........El IRE )£FONC_Bi E POUR ''Ii: 'if:'} LiGNE // Lrltt iLE (CiiAQLE (}OTIS}// I'21: iii fi _NLET (BOTH SIDES) I[CR(Z_ CCI_NI[CIONS...
- Page 16 FIGURE 8.1 Wiring diagram, Beckett burner > o ©o 445 01 4094 04...
- Page 17 FIGURE 8.2 Wiring diagram, Riello 40-F or BF burner (without 24 VAC control) 445 01 4094 04...
- Page 18 FIGURE 8.3 Wiring diagram, Riello 40-F or BF burner (with 24 VAC control) < C(}i 445 01 4094 04...
-
Page 19: Parts List
PARTS LIST Models : AMP & NOMF 105 / 106, Beckett AFG and 40-F Riello burner (without 24 VAC control) B50058A 445 01 4094 04... - Page 20 PARTS LIST Models : AMP & NOMF 105 / 106, Beckett AFG and 40-F Riello burner (without 24 VAC control) HEAT EXCHANGER B01667 REAR PANEL ASSEMBLY B01728 Includes panel, insulation and baffle INSULATION, REAR PANEL B01986 REAR BAFFLE B01898 PANEL ASSEMBLY, RIGHT SIDE B01885-01 Includes panel, insulation and baffle...
- Page 21 PARTS LIST --'_ Models : AMP & NOMF 120 / 155 / 156, Beckett AFG and Riello 40-F burner (without 24 VAC control) B50062B 445 01 4094 04...
- Page 22 PARTS LIST Models : AMP & NOMF 120 / 155 / 156, Beckett AFG and Riello 40-F burner (without 24 VAC control) <-- HEAT EXCHANGER B01787 REAR PANEL ASSEMBLY B01877 Includes panel, insulation and baffle INSULATION B01526-25 REAR BAFFLE B01988 PANEL ASSEMBLY, RIGHT SIDE B01875-01...
- Page 23 PARTS LIST Models : AMP & NOMF 120 / 156, Riello 40-F burner (with 24 VAC control) B50085A 445 01 4094 04...
- Page 24 PARTS LIST Models : AMP & NOMF 120 / 156, Riello 40-F burner (with 24 VAC control) B01787 HEAT EXCHANGER ASSEMBLY BAFFLE AND GASKETS NOT INCLUDED B01988 REAR BAFFLE B01877 REAR PANEL ASSEMBLY INCLUDES PANEL, INSULATION ANS BAFFLE B01526-25 INSULATION B01874 FRONT TOP PANEL ASSEMBLY INCLUDES PANEL AND LATCH...
- Page 25 PARTS LIST Model : AMP120, Riello 40-BF burner B50078A 445 01 4094 04...
- Page 26 PARTS LIST Model : AMP120, Riello 40-BF burner HEAT EXCHANGER B01787 REAR PANEL ASSEMBLY B01877 Includes panel, insulation and baffle INSULATION B01526-25 REAR BAFFLE B01988 PANEL ASSEMBLY, RIGHT SIDE B01875-01 Includes panel, insulation and baffle INSULATION, SIDE PANEL B01800-01 RIGHT LATERAL BAFFLE B01805-01 FRONT TOP PANEL...
Need help?
Do you have a question about the AMP105-1E2 and is the answer not in the manual?
Questions and answers