Programming The Control - GE GXSF27B Owner's Manual & Installation Instructions

Programming the Control
CONTROL SETTINGS REQUIRED upon installation and
after an extended power outage.
NOTES:
• WHEN THE TIL*_NSFORMER IS PI,UGGED INTO THE
ELECTRICAL OUTLET (see step 9), 12:00 AM (flashing),
and PRESENT TIME show in the display area. Program the
conuol as insu_ucted below, ff SR -- is flashing, use tile UP (+)
/o\ button to set the correct SR code as ti)lh)ws: SR35 fi)r GNSF35,
SR31 ti)r GXSF39, or SR22 ti)r GXSF27. Ifyou pass by tile correct
code number, use the DOWN (-) W button. Then press the
SEI_ECT button and program the control.
• A "beep" sounds while pressing buttons tor conuol programming.
One beep signals a change in the conuol (fisplay. Repeated beeps
mean the conuol will not accept a change flom tile button you
haw pressed, and you should use another button.
• Toprogramtheconuol, youwillusetheUP (+) /o\,
DOWN (-) W and SEI_ECT buttons.
Display
TOUCH or HOLD button
UP(4
SmartWater Softener System- _,J
SELECT button
l&
SET PRESENT TIME OF DAY .....
NOTE: If tile words PRESENT TIME do not sh_)w in tile display,
press tile SEI_ECT button until they do.
1. Press the UP (+) _ or DO_VN (-) _ button to set. The UP
button moves the display ahead; the DOWN button moves the
time backward.
If tile present time is between noon and midnight, be sure PM
shows _, ff-I,_ I"
C ' 0d
I
mEs_r rl_
NOTE: Each press of an UP (+) _ or DOWN (-) W button changes
the time by one minute. Holding tile button in changes tile time
32 minutes each second
,_,,_r-_l ' l'-I'-i' -'_-I_J_
•
2. When tile present time shows, press SELECT to set. If the present
time is between midnight and noon. be sure AM sh_)ws.
SET WATER HARDNESS NUMBER 11--7-
NOTE:
If 15 (facto U defauh)
and
/,_!
tLa.RDNESS do not show in the
display, press SEI_ECT until they do.
1. Press the UP (+)/o\ or DOX.VN (-) _] button to set w)ur water
hardness number in the display. DOWN (-) W moves the display
down u) 1. UP (+) _ moves tile maximum setting.
NOTE: Each press of a button changes the display by 1 between 1
and 25. Above 25, the display changes 5 at a time (25, 30, 35, etc.).
Hol(fing a button in changes the numbers twice each second.
2. When your water hardness number sh_)ws, press SEI _ECT to set.
NOTE: If there is clear water iron in your water supply, you will
need to increase the hardness setting by 5 for each 1 ppm of clear
water iron in your water supply.
You can get the grains per gallon (gpg) hardness of your water
supply from a water analysis lalmratory, or call and ask your local
water department, if you are on a mmficipal supply, or call GE
Answer Center ® to request a water harthless test kit. If your report
shows hardness in parts per million (ppm) simply divide by 17.1 to
get the equivalent number of grains per .qallon.
SET REGENERATION (STARTING) TIME
NOTE: RECtL_R(;E TIME and a flashing 2:00 AM
(tacto U detault) should show in the display. This is a good
time fi)r regeneration lo start ((wet in about 2 hours) in most
households because water is not in use. HARD WATER is
bypassed to house fimcets during regeneration.
If no chmage is needed, go m step 2. To change the
regeneration starting time, fifth)w step 1.
1. Press the UP (+) _ or DOWN (-) W button to set the
desired regeneration start time.
NOTE: Each press of the buttons changes tim time by l hour.
Holding the buttons in changes the time twice ea(h second.
2. t tess tile SELECT button once more.
, la II I
Be sure to observe tile AM or l M, as _ _
you did when setting the time of day.
The display shows tile present time of day and RECHARGE
TONIGHT.
I
I
itECHA PGE TON/Gt/T