Page 1 Compass 2 0 1 0 OWNE R ’ S MANUAL...
Page 2: Introduction
TABLE OF CONTENTS SECTION PAGE ............3 INTRODUCTION .
Page 4: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Warnings And Cautions ....7 Rollover Warning .
Page 5: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
Page 6: How To Use This Manual
INTRODUCTION 5 control. Failure to operate this vehicle safely may result belts could cut the highway death toll by 10,000 or more in an accident, rollover of the vehicle, and severe or fatal each year and could reduce disabling injuries by two injury.
Page 7 6 INTRODUCTION...
Page 8: Warnings And Cautions
INTRODUCTION 7 WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 9: Vehicle Modifications/Alterations
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 10: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Vehicle Security Alarm — If Equipped ..18 Ignition Key Removal .
Page 11 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock The Doors And Liftgate ..21 Child-Protection Door Lock System (Rear Doors) ......32 Sound Horn With Remote Key Lock .
Page 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Automatic Locking Retractors (ALR) Airbag Deployment Sensors And Controls . . . 63 Mode — If Equipped ....48 Event Data Recorder (EDR) .
Page 13: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal The authorized dealer that sold you your new vehicle has Automatic Transmission — If Equipped the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys.
Page 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: If you try to remove the key before you place the shift lever in PARK, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described.
Page 15 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked car is an invitation to thieves. Always remove the key from the ignition and lock all the doors when leaving the vehicle unattended. Manual Transmission — If Equipped 1. Turn the ignition switch to the ACC (Accessory) position.
Page 16: Locking Doors With A Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Locking Doors With A Key The system uses ignition keys that have an embedded You can insert the key with either side up. To lock the electronic chip (transponder) to prevent unauthorized door, turn the key to the right.
Page 17: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the Vehicle Security Light turns on during normal CAUTION! vehicle operation (vehicle running for longer than 10 sec- onds), it indicates that there is a fault in the electronics. Always remove the Sentry Keys from the vehicle Should this occur, have the vehicle serviced as soon as and lock all doors when leaving the vehicle unat- possible by an authorized dealer.
Page 18: Customer Key Programming
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Customer Key Programming 4. Insert a blank Sentry Key into the ignition switch. If you have two valid Sentry Keys , you can program Turn the ignition switch to the ON position within new Sentry Keys to the system by performing the 60 seconds.
Page 19: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE reprogrammed. All vehicle keys must be taken to an will flash repeatedly for three minutes. If the disturbance authorized dealer at the time of service to be is still present (driver’s door, passenger door, other doors, reprogrammed.
Page 20: To Disarm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 disarm. After approximately 16 seconds, the Vehicle Security Light will flash slowly. This shows that the Vehicle Security Alarm is fully armed. To Disarm The System Press UNLOCK on the RKE transmitter, or insert the key into the ignition switch and turn the ignition switch to the ON position.
Page 21: To Unlock The Doors And Liftgate
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the To Unlock The Doors And Liftgate Press and release the UNLOCK button on the RKE following steps: transmitter once to unlock the driver’s door, or twice 1.
Page 22: Illuminated Approach - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Security Alarm activated will cause the alarm to sound. Sound Horn With Remote Key Lock Press the UNLOCK button to deactivate the Vehicle This feature will cause the horn to chirp when the doors Security Alarm.
Page 23: Flash Lights With Remote Key Lock/Unlock
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Test the feature while outside of the vehicle by press- Flash Lights With Remote Key Lock/Unlock ing the LOCK button on the RKE transmitter with the This feature will cause the turn signal lights to flash when ignition switch in the LOCK position and the key re- the doors are locked or unlocked with the RKE transmit- moved.
Page 24: Using The Panic Alarm
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 3. Test the feature while outside of the vehicle by press- The Panic Alarm will stay on for three minutes unless ing the LOCK/UNLOCK buttons on the RKE transmitter you turn it off by pressing the PANIC button a second with the ignition switch in the LOCK position and the time or if the vehicle speed is 5 mph (8 km/h) or greater.
Page 25: Transmitter Battery Replacement
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. This device must accept any interference that may be The recommended replacement battery is CR2032. received including interference that may cause undesired 1. If the RKE transmitter is equipped with a screw, operation.
Page 26: Remote Starting System - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 2. Remove and replace the battery. Avoid touching the How to Use Remote Start new battery with your fingers. Skin oils may cause All of the following conditions must be met before the battery deterioration.
Page 27 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE will chirp twice (if programmed). Then, the engine will WARNING! start and the vehicle will remain in the Remote Start • Do not start or run an engine in a closed garage or mode for a 15-minute cycle.
Page 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 Remote start will also cancel if any of the following occur: NOTE: To avoid unintentional shut downs, the system will disable the one time press of the REMOTE START • The engine stalls or RPM exceeds 2500 button for two seconds after receiving a valid Remote •...
Page 29: Door Locks
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR LOCKS WARNING! Manual Door Locks • For personal security and safety in the event of an Use the manual door lock plunger to lock the doors from accident, lock the vehicle doors as you drive as inside the vehicle.
Page 30: Power Door Locks
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Power Door Locks A power door lock switch is located on the driver’s door panel. Press this switch to lock or unlock the doors and liftgate. NOTE: To prevent from locking the key in the vehicle, the power door lock switch will not operate when the key is in the ignition and either front door is open.
Page 31 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the 2. The transmission is in gear. following procedure: 3. All doors are closed. 1. Close all doors and place the key in the ignition 4.
Page 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 NOTE: Automatic Unlock Doors on Exit Programming • If you do not hear the chime it means that the system The Automatic Unlock Doors On Exit feature can be did not enter the programming mode and you will enabled or disabled as follows: need to repeat the procedure.
Page 33: Child-Protection Door Lock System (Rear Doors)
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. A single chime will indicate the completion of the Child-Protection Door Lock System (Rear Doors) programming. Insert the tip of the ignition key into the lock and rotate to the LOCK or UNLOCK position. 5.
Page 34: Power Windows - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 NOTE: For emergency exit with the system engaged, move the lock plunger up (unlocked position), roll down the window and open the door with the outside door handle. POWER WINDOWS — IF EQUIPPED Power Window Switches The window controls on the driver’s door trim panel control all the door windows.
Page 35: Auto-Down
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles equipped with the EVIC, the power window switches will remain active for up to 10 min- utes after the ignition switch is turned to the LOCK position. Opening either front door will cancel this feature.
Page 36: Window Lockout Switch
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Window Lockout Switch LIFTGATE The window lockout switch on the driver’s door allows NOTE: The key that is used to start the vehicle is also you to disable the window control on the other doors. To used to lock or unlock the doors and open the liftgate.
Page 37 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Once unlocked, the liftgate can be opened or closed NOTE: • In the event of a power malfunction, or the RKE without using the key. To open the liftgate, squeeze the liftgate release and pull the liftgate open with one fluid transmitter is inoperative, insert the key into the motion.
Page 38: Occupant Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 • Supplemental Rear Impact Active Head Restraints WARNING! (Continued) (AHR) located on top of the front seats (integrated into • If you are required to drive with the liftgate open, the head restraint) make sure that all windows are closed, and the •...
Page 39 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE all the way out and then adjusting the belt to the WARNING! desired length to restrain a child seat or secure a large item in a seat — if equipped In a collision, you and your passengers can suffer much greater injuries if you are not properly buckled If you will be carrying children too small for adult-sized up.
Page 40: Lap/Shoulder Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 ejection and the risk of injury caused by striking the WARNING! inside of the vehicle. Everyone in a motor vehicle should • It is extremely dangerous to ride in a cargo area, be belted at all times.
Page 41 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is along side the pillar near the WARNING! (Continued) back of your seat. Grasp the latch plate and pull out the • Wearing your belt in the wrong place could make belt.
Page 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.
Page 43 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your WARNING! (Continued) abdomen. To remove slack in the lap belt portion, pull up • A belt that is worn under your arm is very danger- on the shoulder belt.
Page 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 6. To release the belt, push the red button on the buckle. WARNING! The belt will automatically retract to its stowed position. • A lap belt worn too high can increase the risk of If necessary, slide the latch plate down the webbing to allow the belt to retract fully.
Page 45: Adjustable Upper Shoulder Belt Anchorage
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push the anchorage button to release the anchorage, and move it up or down to the position that fits you best.
Page 46: Second Row Center Lap/Shoulder Belt Operating Instructions
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 In the rear seat, move toward the center of the seat to position the belt away from your neck. Second Row Center Lap/Shoulder Belt Operating Instructions The second row center lap/shoulder belt features a three-point seat belt with a mini-latch and buckle, which allows the shoulder belt to detach from the lower anchor when the seat is folded.
Page 47 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Route the shoulder belt to the inside of the right head 5. Sit back in the seat. Slide the regular latch plate up the restraint. webbing as far as necessary to allow the belt to go around your lap.
Page 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 7. Position the lap belt across your thighs, below your 8. Position the shoulder belt on your chest so that it is abdomen. To remove slack in the lap belt portion, pull up comfortable and not resting on your neck.
Page 49: Lap/Shoulder Belt Untwisting Procedure
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE button on the top of the mini-buckle. The belt will 4. Continue to slide the latch plate up until it clears the automatically retract to its stowed position. If necessary, folded webbing. slide the latch plate down the webbing to allow the belt Automatic Locking Retractors (ALR) Mode —...
Page 50: Seat Belt Pretensioners - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 2. Grasp the shoulder portion and pull downward until NOTE: These devices are not a substitute for proper seat the entire belt is extracted. belt placement by the occupant. The seat belt still must be worn snugly and positioned properly.
Page 51 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How the Active Head Restraints (AHR) Work The Occupant Restraint Controller (ORC) determines whether the severity or type of rear impact require the Active Head Restraints (AHR) to deploy. In case of AHR deployment both driver and front passenger seat AHR’s will be deployed.
Page 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 1. Grasp the deployed AHR from the rear seat. CAUTION! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of an accident.
Page 53 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 3 — Final Downward Movement To Engage Locking Mecha- nism 4. The AHR front soft foam and trim half should lock 1 —...
Page 54: Enhanced Seat Belt Use Reminder System (Beltalert )
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Enhanced Seat Belt Use Reminder System (BeltAlert ) If the driver’s seat belt has not been buckled within 60 seconds of starting the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the BeltAlert will alert the driver to buckle the seat belt.
Page 55 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE BeltAlert Programming NOTE: Watch for the Seat Belt Reminder Light to turn BeltAlert can be enabled or disabled by your authorized on while unbuckling and off while re-buckling the seat dealer or by performing the following procedure: belt.
Page 56: Seat Belt Extender
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Seat Belt Extender Seat Belts And Pregnant Women If a seat belt is too short, even when fully extended, and We recommend that pregnant women use the seat belts when the adjustable upper shoulder belt anchorage (if throughout their pregnancy.
Page 57: Supplemental Restraint System (Srs) - Airbags
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Restraint System (SRS) - Airbags This vehicle has airbags for both the driver and front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the center of the steering wheel.
Page 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 • Front Passenger Airbag This vehicle is equipped with Supplemental Side Airbag Inflatable Curtains (SABIC) to protect the driver, front, • Supplemental Rear Impact Active Head Restraint for and rear passengers sitting next to a window. The SABIC Driver and Front Passenger are located above the side windows.
Page 59: Advanced Front Airbag Features
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Advanced Front Airbag Features WARNING! The Advanced Front Airbag system has multistage driver • No objects should be placed over or near the and front passenger airbags. This system provides output appropriate to the severity and type of collision as airbag on the instrument panel, because any such determined by the Occupant Restraint Controller (ORC), objects could cause harm if the vehicle is in a crash...
Page 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Supplemental Side Seat Airbags — If Equipped Supplemental side seat airbags provide enhanced protec- tion and work together with supplemental Side Airbag Inflatable Curtains (SABIC) to help protect an occupant during a side impact. The supplemental side seat airbag is marked with an airbag label sewn into the outboard side of the seat.
Page 61 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Airbag Inflatable Curtain (SABIC) SABIC airbags offer side-impact and vehicle rollover protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each airbag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for side-impact head injuries.
Page 62: Knee Impact Bolsters
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 The system includes sensors adjacent to both front and Knee Impact Bolsters rear seat occupants that are calibrated to deploy the The Knee Impact Bolsters help protect the knees of the SABIC airbags during impacts that require airbag occu- driver and the front passenger, and position everyone for pant protection.
Page 63 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You should read the instructions provided with your WARNING! child restraint to make sure that you are using it properly. Infants in rear facing child restraints should NEVER 2. All occupants should ALWAYS wear their lap and ride in the front seat of a vehicle with a passenger shoulder belts properly.
Page 64: Airbag Deployment Sensors And Controls
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Airbag Deployment Sensors and Controls WARNING! Occupant Restraint Controller (ORC) • Relying on the airbags alone could lead to more The ORC is part of a Federally regulated safety system severe injuries in a collision. The airbags work required for this vehicle.
Page 65 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Advanced Front Airbags will not deploy in all frontal The ORC monitors the readiness of the electronic parts of collisions, including some that may produce substantial the system whenever the ignition switch is in the START vehicle damage —...
Page 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 It also includes diagnostics that will illuminate the instru- the Advanced Front Airbags. Different airbag inflation ment cluster Airbag Warning Light if a malfunction is rates are possible, based on the collision type and sever- noted.
Page 67 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC determines if a side collision requires the side Supplemental Side Airbag Inflatable Curtain airbags to inflate based on the severity and type of (SABIC) Inflator Units — If Equipped collision. During collisions where the impact is confined to a particular area of the side of the vehicle, the ORC may The ORC monitors the readiness of the electronic parts of...
Page 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 • Flash hazard lights as long as the battery has power or Because airbag sensors estimate deceleration over time, vehicle speed and damage are not good indicators of until the ignition key is turned off. whether or not an airbag should have deployed.
Page 69 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision, which deploys the airbags, any throat irritation, move to fresh air. If the irritation or all of the following may occur: continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s in- •...
Page 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Maintaining Your Airbag System WARNING! (Continued) • Do not attempt to modify any part of your ad- WARNING! vanced airbag system. The airbag may inflate • Modifications to any part of the airbag system accidentally or may not function properly if modi- could cause it to fail when you need it.
Page 71: Event Data Recorder (Edr)
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light located on the inside of the fuse block cover for the You will want to have the airbags ready to proper airbag fuses. See your authorized dealer if the inflate for your protection in a collision.
Page 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 2. Under certain circumstances, EDR data may not be accessing the electronic data stored, unless ordered to recorded (e.g., loss of battery power). download data by a court with legal jurisdiction (i.e., pursuant to a warrant).
Page 73: Child Restraint
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Requested by police under a legal warrant. United States and all Canadian provinces require that small children ride in proper restraint systems. This is the 4. Otherwise required by law. law, and you can be prosecuted for ignoring it. Data parameters that are recorded: Children 12 years and younger should ride properly •...
Page 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Infants and Child Restraints to about 20 lbs (9 kg). Convertible child seats can be There are different sizes and types of restraints for used either rearward-facing or forward-facing in the children from newborn size to the child almost large vehicle.
Page 75 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE in the vehicle by the lap/shoulder belt or the LATCH WARNING! child restraint anchorage system. Refer to LATCH — • Improper installation can lead to failure of an Child Seat Anchorage System (Lower Anchors and Tether for CHildren) .
Page 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 that you can install the child restraint in the vehicle retractor and then allow the belt to retract into the where you will use it, before you buy it. retractor. For additional information on ALR, refer to “Automatic Locking Mode”.
Page 77 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Any seat belt system will loosen with time, so check over the front of the seat when their back is against the the belt occasionally, and pull it tight if necessary. seatback should use the lap/shoulder belt in a rear seat. •...
Page 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 have lower anchorages that are capable of accommodat- ing LATCH-compatible child seats having flexible, webbing-mounted lower attachments. Child seats with fixed lower attachments must be installed in the out- board positions only. Regardless of the specific type of lower attachment, NEVER install LATCH-compatible child seats such that two seats share a common lower anchorage.
Page 79 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provide add-on tether strap kits for some of their older restraint installation, instead of tucking the seat belt products. Tether anchorage kits are also available for behind the child restraint, route the seat belt through the most older vehicles.
Page 80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 In general, you will first loosen the adjusters on the lower Not all child restraint systems will be installed as we and tether straps so that you can attach the hook or have described here.
Page 81: Engine Break-In Recommendations
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets The engine oil installed in the engine at the factory is a Airbags deploying in the front seat could harm your pet. high-quality energy conserving type lubricant. Oil An unrestrained pet will be thrown about and possibly changes should be consistent with anticipated climate injured, or injure a passenger during panic braking or in conditions under which vehicle operations will occur.
Page 82: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 SAFETY TIPS Exhaust Gas Transporting Passengers WARNING! NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. WARNING! Breathing it can make you unconscious and can eventually poison you.
Page 83: Safety Checks You Should Make Inside The Vehicle
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you are required to drive with the trunk/liftgate open, Safety Checks You Should Make Inside the make sure that all windows are closed and the climate Vehicle control BLOWER switch is set at high speed. DO NOT Seat Belts use the recirculation mode.
Page 84: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 Defroster Lights Check operation by selecting the defrost mode and place Have someone observe the operation of exterior lights the blower control on high speed. You should be able to while you work the controls. Check turn signal and high feel the air directed against the windshield.
Page 86: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......89 Uconnect™ phone — If Equipped ... 93 Inside Day/Night Mirror .
Page 87 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Command — If Equipped ... 121 Adjusting Active Head Restraints ..133 Voice Command System Operation ..121 Folding Rear Seat .
Page 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Flash-To-Pass ..... . . 143 To Vary The Speed Setting ....150 Map/Reading Lights .
Page 89 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening The Sunroof ....159 Glove Compartment And Storage Bin ..166 Closing The Sunroof .
Page 90: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicle).
Page 91: Outside Mirror - Driver Side
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Driver Side Adjust the flat outside mirror so you can just see the side of your vehicle in the part of the mirror closest to the vehicle with your head close to the door glass. Outside Mirror —...
Page 92: Power Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Power Mirrors To adjust a mirror, turn the control wand toward the left The control for the power mirrors is located on the or right mirror positions indicated. Tilt the control wand driver’s door trim panel. in the direction you want the mirror to move.
Page 93: Heated Mirrors - If Equipped
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.
Page 94: Uconnect™ Phone - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 • www.jeep.com/uconnect Uconnect™ Phone — IF EQUIPPED Uconnect™ Phone is a voice-activated, hands-free, in- • or call 1–877–855–8400 vehicle communications system. Uconnect™ Phone al- lows you to dial a phone number with your cellular Uconnect™...
Page 95 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE linked (or paired) cellular phone can be used with the Voice Command Button system at a time. The system is available in English, Actual button location may vary with the ra- Spanish, or French languages. dio.
Page 96: Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • For each feature explanation in this section, only the The radio display will be used for visual prompts from the Uconnect™ Phone such as CELL or caller ID on combined form of the voice command is given. You certain radios.
Page 97 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To activate the Uconnect™ Phone from idle, simply press The following are general phone to Uconnect™ Phone button and follow the audible prompts for pairing instructions: directions. All Uconnect™ Phone sessions begin with a •...
Page 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 • You will then be asked to give your cellular phone a • The system will prompt you to say the number you priority level between one and seven, with one being want to call. the highest priority.
Page 99 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, enter the number designation (e.g., or downloaded phonebook. To learn how to store a name in the phonebook, refer to Add Names to Your Home, Work, Mobile, or Pager ). This will allow Uconnect™...
Page 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • Depending on the maximum number of entries down- Phonebook Download – Automatic Phonebook Transfer From Cellular Phone loaded, there may be a short delay before the latest If equipped and specifically supported by your phone, downloaded names can be used.
Page 101 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Phonebook Download — Single Entry first disconnect or drop the Bluetooth connection to If equipped and supported by your phone, Uconnect™ the Uconnect™ Phone, and then send the address Phone allows the user to download entries from their book entry via Bluetooth .
Page 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 • You will then be asked for the name of the phonebook Delete Uconnect™ Phonebook Entry entry that you wish to edit. NOTE: Editing phonebook entries is recommended • Next, choose the number designation (home, work, when the vehicle is not in motion.
Page 103 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After you enter the name, the Uconnect™ Phone will • Note that only the phonebook in the current language ask you which designation you wish to delete: home, is deleted. work, cellular, pager, or all. Say the designation you •...
Page 104: Phone Call Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • The Uconnect™ Phone will then prompt you as to the call, press and hold the button until you hear a number designation you wish to call. single beep, indicating that the incoming call was rejected.
Page 105 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE by the phone number or phonebook entry you wish to Conference Call call. The first call will be on hold while the second call is When two calls are in progress (one active and one on in progress.
Page 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Call Termination Call Continuation To end a call in progress, momentarily press the Call continuation is the progression of a phone call on the Uconnect™ Phone after the vehicle ignition key has been button.
Page 107: Uconnect™ Phone Features
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone Features Emergency Assistance If you are in an emergency and the cellular phone is Language Selection reachable: To change the language that the Uconnect™ Phone is • Pick up the phone and manually dial the emergency using: number for your area.
Page 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Canada and 060 for Mexico). The number dialed may Towing Assistance not be applicable with the available cellular service If you need towing assistance: and area. • Press the button to begin. • If supported, this number may be programmable on •...
Page 109 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Paging When calling a number with your Uconnect™ Phone that To learn how to page, refer to Working with Automated normally requires you to enter in a touch-tone sequence Systems. Paging works properly except for pagers of on your cellular phone keypad, you can press the certain companies, which time out a little too soon to button and say the sequence you wish to enter, followed...
Page 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 The Uconnect™ Phone will then send the corresponding Turning Confirmation Prompts ON/OFF phone number associated with the phonebook entry, as Turning confirmation prompts off will stop the system tones over the phone. from confirming your choices (e.g., the Uconnect™ Phone will not repeat a phone number before you dial it).
Page 111: Advanced Phone Connectivity
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using the Cellular Phone Keypad Mute/Un-Mute (Mute OFF) You can dial a phone number with your cellular phone When you mute the Uconnect™ Phone, you will still be keypad and still use the Uconnect™ Phone (while dialing able to hear the conversation coming from the other via the cellular phone keypad, the user must exercise party, but the other party will not be able to hear you.
Page 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • When prompted, say List Phones. from your Uconnect™ Phone paired cellular phone to the Uconnect™ Phone or vice versa, press the button • The Uconnect™ Phone will play the phone names of and say Transfer Call.
Page 113: Things You Should Know About Your Uconnect™ Phone
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The selected phone will be used for the next phone Things You Should Know About Your Uconnect™ call. If the selected phone is not available, the Phone Uconnect™ Phone will return to using the highest Uconnect™...
Page 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 • Speak normally, without pausing, just as you would Repeat the words and phrases when prompted by the Uconnect™ Phone. For best results, the Voice Training speak to a person sitting a few feet/meters away from session should be completed when the vehicle is parked you.
Page 115 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When navigating through an automated system such • In a convertible vehicle, system performance may be as voice mail, or when sending a page, at the end of compromised with the convertible top down. speaking the digit string, make sure to say Send.
Page 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 • Performance, such as audio clarity, echo, and loudness Bluetooth Communication Link to a large degree rely on the phone and network, and Cellular phones have been found to lose connection to not the Uconnect™ Phone. the Uconnect™...
Page 117 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117...
Page 119 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 121 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
Page 122: General Information
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 General Information NOTE: Take care to speak into the Voice Interface This device complies with Part 15 of the FCC rules and System as calmly and normally as possible. The ability of RSS 210 of Industry Canada. Operation is subject to the the Voice Interface System to recognize user voice com- following conditions: mands may be negatively affected by rapid speaking or a...
Page 123 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If you do not say a command within a few For example, if you are in the disc menu and you are seconds, the system will present you with a list of listening to FM radio, you can speak commands from the options.
Page 124: Commands
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Commands In this mode, you can say the following commands: The Voice Command system understands two types of • “Radio” (to switch to the radio mode) commands. Universal commands are available at all •...
Page 125 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Previous Channel” (to select the previous channel) Radio FM To switch to the FM band, say “FM” or “Radio FM”. In • “List Channel” (to hear a list of available channels) this mode, you may say the following commands: •...
Page 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Memo − “Previous” (to play the previous memo) To switch to the voice recorder mode, say “Memo”. In − “Delete” (to delete a memo) this mode, you may say the following commands: • “Delete All” (to delete all memos) •...
Page 127: Voice Training
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Keep in mind that you have to press the Voice SEATS Command button first and wait for the beep Seats are a primary part of the Occupant Restraint System of the vehicle. They need to be used properly for safe before speaking the “Barge In”...
Page 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 desired. Then, using body pressure, move forward and WARNING! rearward on the seat to be sure that the seat adjusters have latched. Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control.
Page 129: Manual Seat Height Adjustment - If Equipped
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Seat Height Adjustment — If Equipped Manual Lumbar — If Equipped The driver’s seat height can be raised or lowered by using The lumbar adjustment handle is located on the outboard the handle on the outboard side of the seat to adjust the side of the driver’s seat.
Page 130: Driver's Seatback Recline
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Driver’s Seatback Recline WARNING! To recline the seatback, lean forward before lifting the handle, then lean back to the desired position and release Do not ride with the seatback reclined so that the the handle.
Page 131: Six-Way Power Seats - If Equipped
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Six-Way Power Seats — If Equipped WARNING! The power seat switch is located on the outboard side of the seat near the floor. Use the switch to move the seat up, Adjusting a seat while the vehicle is moving is down, forward, rearward, or to tilt the seat.
Page 132: Heated Seats - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Heated Seats — If Equipped turn the heater and the remaining indicator light off after This feature heats the front driver and passenger seats. an additional 30 minutes of continuous operation. If The heaters provide the same heat level for both the seat Low-level heating is selected, the system automatically cushion and the seatback.
Page 133: Fold-Flat Front Passenger Seat
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold-Flat Front Passenger Seat WARNING! (Continued) To fold the front passenger seat, lift the recliner handle to • Do not place anything on the seat that insulates the full upward position and push the seatback forward against heat, such as a blanket or cushion.
Page 134: Adjusting Active Head Restraints
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Adjusting Active Head Restraints Active Head Restraints can reduce the risk of injury in the event of a rear impact. The Active Head Restraint should be adjusted so the top of the head restraint is located above the top of your ear.
Page 135 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To raise the head restraint, pull upward on the head For comfort the Active Head Restraints can be tilted restraint (on some models, you may need to press the forward and backward. To tilt the head restraint closer to push button).
Page 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 • In the event of deployment of an Active Head Re- straint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things to Know Before Starting Your Vehicle” for further information. WARNING! • Driving a vehicle with the head restraints removed or improperly adjusted could cause serious injury or death in the event of a collision.
Page 137: Folding Rear Seat
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat WARNING! (Continued) To provide additional storage area, each rear seatback can • Do not place items over the top of the Active Head be folded forward. Pull the strap forward to move the Restraint, such as coats, seat covers or portable seat forward and flat.
Page 138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 WARNING! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
Page 139: To Open And Close The Hood
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Pull the hood release lever located on the left kick WARNING! panel. • Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured.
Page 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 CAUTION! To prevent possible damage, do not slam the hood to close it. Lower the hood until it is open approxi- mately 8 in (20 cm) and then drop it. This should secure both latches. Never drive your vehicle unless the hood is fully closed, with both latches engaged.
Page 141: Lights
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Headlights and Parking Lights Turn the end of the multifunction lever to the first detent Multifunction Lever to turn on the parking lights. The multifunction lever controls the operation of the headlights, parking lights, turn signals, headlight beam Turn the end of the lever to the second detent to turn on selection, instrument panel light dimming, interior lights, the headlights.
Page 142: Instrument Panel Dimming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Instrument Panel Dimming Rotate the center portion of the lever to the extreme bottom position to fully dim the instrument panel lights and prevent the interior lights from illuminating when a door is opened. Rotate the center portion of the lever up to increase the brightness of the instrument panel lights when the park- ing lights or headlights are on.
Page 143: Fog Lights - If Equipped
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fog Lights — If Equipped NOTE: The fog lights will only operate with the head- The front fog light switch is on the multifunction lights on low beam. Selecting high beam headlights will lever.
Page 144: Lane Change Assist
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Lane Change Assist Tap the lever up or down once, without moving beyond the detent, and the turn signal (right or left) will flash three times then automatically turn off. High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beam.
Page 145: Map/Reading Lights
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Map/Reading Lights NOTE: The lights will remain on until the switch is These lights are mounted between the sun visors above pressed a second time, so be sure they have been turned the rear view mirror. Each light is turned on by pressing off before leaving the vehicle.
Page 146: Windshield Wiper Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Windshield Wiper Operation Rotate the end of the lever upward to the LO position for low-speed wiper operation. Rotate the end of the lever upward to the HI position for high-speed wiper operation. Wiper/Washer Control Lever Wiper Control...
Page 147: Intermittent Wiper System
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System Windshield Washers Use the intermittent wiper when weather conditions To use the washer, pull the control lever toward you and make a single wiping cycle, with a variable pause be- hold while spray is desired.
Page 148: Mist Feature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Mist Feature CAUTION! Push down on the control lever to activate a single wipe to clear the windshield of road mist or spray from a In cold weather, always turn off the wiper switch and passing vehicle.
Page 149: Electronic Speed Control - If Equipped
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Push down on the lever to unlock the steering column. WARNING! With one hand firmly on the steering wheel, move the steering column up or down, as desired. Push the lever Do not adjust the steering column while driving. up to lock the steering column firmly in place.
Page 150: To Activate
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 simultaneously. If this occurs, the Electronic Speed Con- trol System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. To Activate Push the ON/OFF button. The CRUISE indicator in the instrument cluster will illuminate.
Page 151: To Set A Desired Speed
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set a Desired Speed To Vary the Speed Setting When the vehicle has reached the desired speed, press When the Electronic Speed Control is set, you can in- down on the lever and release. Release the accelerator crease speed by pushing up and holding the RESUME and the vehicle will operate at the selected speed.
Page 152: Manual Transaxle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Tapping the SET DECEL lever once will result in a 1 mph WARNING! (1.6 km/h) speed decrease. Each time the lever is tapped, speed decreases. Electronic Speed Control can be dangerous where the system cannot maintain a constant speed.
Page 153: Garage Door Opener - If Equipped
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE On steep hills a greater speed loss or gain may occur so The HomeLink buttons that are located in the headliner it may be preferable to drive without Electronic Speed or sun visor designate the three different HomeLink Control.
Page 154: Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Programming HomeLink WARNING! Before You Begin • Your motorized door or gate will open and close If you have not trained any of the HomeLink buttons, while you are training the Universal Transceiver. erase all channels before you begin training.
Page 155 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After training a HomeLink channel, if the garage Place the handheld transmitter 1–3 in (3-8 cm) away from the HomeLink button you wish to program while door does not operate with HomeLink and the ga- keeping the indicator light in view.
Page 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 This can usually be found where the hanging antenna 6. Firmly press and release the LEARN or TRAINING wire is attached to the garage door opener motor (it is button. The name and color of the button may vary by NOT the button normally used to open and close the manufacturer.
Page 157: Gate Operator/Canadian Programming
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming successfully accepted the frequency signal. The indica- Canadian radio-frequency laws require transmitter sig- tor light will flash slowly and then rapidly when fully nals to “time-out” (or quit) after several seconds of trained.
Page 158: Reprogramming A Single Homelink Button
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Reprogramming A Single HomeLink Button The HomeLink Universal Transceiver is disabled when To reprogram a channel that has been previously trained, the Vehicle Security Alarm is active. follow these steps: Troubleshooting Tips 1. Turn the ignition switch to the ON/RUN position. If you are having trouble programming HomeLink , here are some of the most common solutions: 2.
Page 159: General Information
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information POWER SUNROOF — IF EQUIPPED This device complies with FCC rules Part 15 and Industry The power sunroof switch is located in the reading light. Canada RSS-210. Operation is subject to the following two conditions: 1.
Page 160: Opening The Sunroof
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Opening the Sunroof WARNING! Manual Mode • Never leave children in a vehicle with the key in To open the sunroof, press and hold the switch rearward the ignition switch. Occupants, particularly unat- to full open.
Page 161: Pinch Protect Feature
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE stop the movement and the sunroof will remain in a Pinch Protect Override partial close condition until the switch is pushed and If a known obstruction (ice, debris, etc.) prevents closing, held forward again. To ensure sunroof is fully closed, press the switch forward and hold for two seconds after press and hold switch until sunroof has completely the reversal occurs.
Page 162: Wind Buffeting
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Wind Buffeting ELECTRICAL POWER OUTLETS Wind buffeting can be described as the perception of There is a standard 12 Volt (13 Amp) power outlet located pressure on the ears or a helicopter-type sound in the in the instrument panel for added convenience.
Page 163 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power is available when the ignition switch is in the ON WARNING! or ACC position. Insert the cigar lighter or accessory plug into the outlet for use. To preserve the heating element, To avoid serious injury or death: •...
Page 164: Power Inverter - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 POWER INVERTER — IF EQUIPPED CAUTION! A 115 Volt (150 Watt) AC power inverter is located on the • Many accessories that can be plugged in draw front of the center console for added convenience. This outlet can power cellular phones, electronics and other power from the vehicle’s battery, even when not in low power devices requiring power up to 150 Watts.
Page 165 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE manually, unplug the device and plug it in again. To WARNING! avoid overloading the circuit, check the power ratings on electrical devices prior to using the inverter. To avoid serious injury or death: •...
Page 166: Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 CUPHOLDERS CAUTION! (Continued) Your vehicle is equipped with four cupholders. There are • Accessories that draw higher power (i.e., coolers, two illuminated cupholders located in the front. vacuum cleaners, lights, etc.) will degrade the battery even more quickly.
Page 167: Storage
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE There are two cupholders located in the back for the rear STORAGE passengers. Glove Compartment And Storage Bin Located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. Rear Cupholders 1 —...
Page 168: Door Storage
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 To open the lower glove compartment, pull outward on Door Storage the release handle. The interior door panels are equipped with lower storage areas. Glove Compartment Front Door Storage...
Page 169: Console Features
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Door Storage Upper Storage Compartment CONSOLE FEATURES To open the lower storage compartment, lift upward on The floor console contains both an upper and lower the lower handle to unlatch the lower storage compart- storage compartment.
Page 170: Cargo Area Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 WARNING! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distrac- tion, resulting in death or injury.
Page 171: Cargo Cover
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press in on the flashlight to release it. Three-Press Switch Cargo Cover Press And Release The cargo area trim panels include two notches for To operate the flashlight, press the switch once for high, mounting the available tonneau cover that accommo- twice for low, and a third time to return to off.
Page 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 To install the Cargo Cover, insert either end of the cover Using the handle, pull the cover toward you and guide into one of the two notches located in the rear trim the rear cover posts into the guides located on both sides panels.
Page 173: Removable Load Floor
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compart- ment.
Page 174: Cargo Tie-Down Loops
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Cargo Tie-Down Loops WARNING! There are four D-rings installed in the cargo area for • Cargo tie-down loops are not safe anchors for a securing cargo. child seat tether strap. In a sudden stop or collision a loop could pull loose and allow the child seat to come loose.
Page 175: Fold Down Speakers - If Equipped
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Place as much cargo as possible in front of the rear axle. Too much weight or improperly placed weight over or behind the rear axle can cause the rear of the vehicle to sway. •...
Page 176: Rear Window Defroster
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 Rotate the center portion of the lever past the first detent to activate that rear washer. The washer pump will continue to operate as long as the lever or ring is engaged. Upon release, the wipers will cycle two times before returning to the set position.
Page 177: Roof Luggage Rack - If Equipped
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE turns off after approximately 10 minutes. For an addi- CAUTION! (Continued) tional five minutes of operation, press the button a • Do not use scrapers, sharp instruments, or abra- second time. sive window cleaners on the interior surface of the NOTE: To prevent excessive battery drain, use the rear window.
Page 178 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....181 Distance To Empty (DTE) ....200 Instrument Cluster .
Page 179 178 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - (Disc Mode For CD Clock Setting Procedure — And MP3/WMA Audio Play, DVD-Video) . . . 214 RER/REN Radio ..... 224 Notes On Playing MP3/WMA Files .
Page 180 UNDERSTANDING YOUR INSTRUMENT PANEL 179 Notes On Playing MP3 Files ... . 243 Uconnect™ Multimedia (Satellite Radio) — If Equipped (REN/REQ/RER/RES/REU/RBZ List Button (CD Mode For MP3 Play) ..245 Radios Only) .
Page 181 180 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Video Radio Operation And Cellular Phones ..259 Entertainment System Climate Controls ..... . 259 (VES)™...
Page 182: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 181 INSTRUMENT PANEL FEATURES 1 — Air Outlet 5 — Storage Bin 9 — Heated Seat Switch – If Equipped 2 — Demisters 6 — Glove Compartment 10 — Hazard Warning Flasher 3 — Instrument Cluster 7 —...
Page 183: Instrument Cluster
182 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 184: Instrument Cluster Descriptions
UNDERSTANDING YOUR INSTRUMENT PANEL 183 INSTRUMENT CLUSTER DESCRIPTIONS If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”. 1. Fuel Gauge / Fuel Door Reminder When the ignition switch is in the ON position, 3.
Page 185 184 UNDERSTANDING YOUR INSTRUMENT PANEL briefly as a bulb check. If the light does not come on 6. Speedometer during starting, have the system checked by an autho- The Speedometer shows the vehicle speed in miles per rized dealer. hour and/or kilometers per hour (mph/kph). 4.
Page 186 UNDERSTANDING YOUR INSTRUMENT PANEL 185 continuous chime will sound to alert you to turn the If the ABS light is on, the brake system should be serviced signals off. If either indicator flashes at a rapid rate, check as soon as possible to restore the benefits of Anti-Lock for a defective outside light bulb.
Page 187 186 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Tachometer normal, turn the engine off immediately and call for The white area of the scale shows the permissible engine service. Refer to “If Your Engine Overheats” in “What To revolutions-per-minute (RPM x 1000) for each gear range. Do In Emergencies”...
Page 188 UNDERSTANDING YOUR INSTRUMENT PANEL 187 booster, the ABS pump will run when applying the brake WARNING! and a brake pedal pulsation may be felt during each stop. Driving a vehicle with the red brake light on is The dual brake system provides a reserve braking capac- dangerous.
Page 189 188 UNDERSTANDING YOUR INSTRUMENT PANEL The light also will turn on when the parking brake is CAUTION! applied with the ignition switch in the ON position. Continuous driving with the Transmission Tempera- NOTE: This light shows only that the parking brake is ture Warning Light illuminated will eventually cause applied.
Page 190 UNDERSTANDING YOUR INSTRUMENT PANEL 189 17. Temperature Gauge WARNING! The temperature gauge shows engine coolant tempera- ture. Any reading within the normal range indicates that A hot engine cooling system is dangerous. You or the engine cooling system is operating satisfactorily. others could be badly burned by steam or boiling coolant.
Page 191 190 UNDERSTANDING YOUR INSTRUMENT PANEL 20. Shift Lever Indicator placard or tire inflation pressure label. (If your vehicle The Shift Lever Indicator is self-contained within the has tires of a different size than the size indicated on the instrument cluster. It displays the gear position of the vehicle placard or tire inflation pressure label, you should automatic transmission.
Page 192 UNDERSTANDING YOUR INSTRUMENT PANEL 191 maintain correct tire pressure, even if under-inflation has tires or wheels on your vehicle, to ensure that the not reached the level to trigger illumination of the TPMS replacement or alternate tires and wheels allow the TPMS low tire pressure telltale.
Page 193 192 UNDERSTANDING YOUR INSTRUMENT PANEL 23. Odometer / Trip Odometer Display Area Vehicle Odometer Messages This display indicates the total distance the vehicle has When the appropriate conditions exist, the following been driven. odometer messages will display: door ......Door Ajar NOTE: U.S.
Page 194 UNDERSTANDING YOUR INSTRUMENT PANEL 193 area. Tighten the fuel filler cap properly and press the reset, this message will continue to display each time you TRIP ODOMETER button to turn off the message. If the turn the ignition switch to the ON/RUN position. To turn problem continues, the message will appear the next time off the message temporarily, press and release the Trip the vehicle is started.
Page 195 194 UNDERSTANDING YOUR INSTRUMENT PANEL 24. Malfunction Indicator Light (MIL) CAUTION! The Malfunction Indicator Light (MIL) is part of an Onboard Diagnostic system called OBD II that Prolonged driving with the MIL on could cause monitors emissions, engine, and automatic trans- damage to the engine control system.
Page 196 UNDERSTANDING YOUR INSTRUMENT PANEL 195 25. Front Fog Light Indicator — If Equipped speeds greater than 30 mph (48 km/h), see your autho- This indicator will illuminate when the front fog rized dealer as soon as possible to have the problem lights are on.
Page 197: Electronic Vehicle Information Center (Evic) - If Equipped
196 UNDERSTANDING YOUR INSTRUMENT PANEL When lit solid: There is an 4WD system fault. 4WD ELECTRONIC VEHICLE INFORMATION CENTER performance will be at a reduced level. Service the 4WD (EVIC) — IF EQUIPPED system soon. The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display that is located in the When blinking: The 4WD system is temporarily dis- instrument cluster.
Page 198 UNDERSTANDING YOUR INSTRUMENT PANEL 197 • Left Front Turn Signal Light Out (with a single chime) The EVIC consists of the following: • System status • Left Rear Turn Signal Light Out (with a single chime) • Vehicle information warning message displays •...
Page 199: Engine Oil Change Indicator System
198 UNDERSTANDING YOUR INSTRUMENT PANEL • Gate Ajar (with a single chime) Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN • Headlamps or Park Lamps On position. To turn off the message temporarily, press and •...
Page 200: Evic Functions
UNDERSTANDING YOUR INSTRUMENT PANEL 199 • Distance To Empty (DTE) EVIC Functions • Elapsed Time • Tire Pressure Monitor (TPM) • Personal Settings To Reset The Display Pressing and holding the EVIC button once will clear the function currently being displayed. Reset will only occur if a resettable function is currently being displayed.
Page 201: Compass/Temperature/Audio
200 UNDERSTANDING YOUR INSTRUMENT PANEL Compass/Temperature/Audio determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel Press and release the EVIC button to display one of eight tank level. This is not resettable. compass headings to indicate the direction the vehicle is facing, the outside temperature, and the current radio NOTE: Significant changes in driving style or vehicle...
Page 202: Elapsed Time
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Elapsed Time Pressing the EVIC button while in this display selects Shows the total elapsed time of travel since the last reset English, Espanol, Deutsch, Italiano, Francais or NL de- when the ignition switch is in the ACC position. Elapsed pending on availability.
Page 203 202 UNDERSTANDING YOUR INSTRUMENT PANEL position (automatic transmission). Press and hold the and hold the EVIC button when in this display until EVIC button when in this display until “ON” or “OFF” “ON” or “OFF” appears to make your selection. appears to make your selection.
Page 204 UNDERSTANDING YOUR INSTRUMENT PANEL 203 power outlets will remain active for up to 10 minutes Display Units In after the ignition switch has been turned OFF. Opening a The EVIC, odometer, and Uconnect™ gps system units vehicle door will cancel this feature. Press and hold the can be changed between English and Metric.
Page 205 204 UNDERSTANDING YOUR INSTRUMENT PANEL large metal or metallic objects) until the “CAL” message panel. This is where the compass module is located and displayed in the EVIC turns off. The compass will now such devices may interfere and cause false compass function normally.
Page 206 UNDERSTANDING YOUR INSTRUMENT PANEL 205 button several times until you have displayed the Per- Compass Calibration sonal Settings (Customer-Programmable Features) menu. If the compass appears erratic or inaccurate, and the Once in the Personal Settings (Customer-Programmable variance has been properly set, you may wish to manu- Features) menu, press and release (less than one second) ally recalibrate the compass.
Page 207: Media Center 230 (Req) - Am/Fm Stereo Radio And 6-Disc Cd/Dvd Changer (Mp3/Wma Aux Jack)
206 UNDERSTANDING YOUR INSTRUMENT PANEL indicator will come on continuously in the EVIC display to indicate that the compass is now in the calibration mode, and that the vehicle can now be driven to calibrate. 5. To complete the compass calibration, drive the vehicle in one or more complete 360–degree circle under 5 mph (8 km/h) in an area free from power lines and large metallic objects, until the “CAL”...
Page 208 UNDERSTANDING YOUR INSTRUMENT PANEL 207 Power Switch/Volume Control (Rotary) SCAN Button Push the ON/VOLUME control knob to turn on the Pressing the SCAN button causes the tuner to search for radio. Press the ON/VOLUME control knob a second the next listenable station in AM, FM or Satellite (if time to turn off the radio.
Page 209 208 UNDERSTANDING YOUR INSTRUMENT PANEL If your vehicle is not equipped with or this feature is not 5. To exit, press any button/knob or wait five seconds. available on your vehicle, a “Not Equipped With The clock can also be set by pressing the SETUP button Uconnect”...
Page 210 UNDERSTANDING YOUR INSTRUMENT PANEL 209 Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob a fifth time Push the rotary TUNE/SCROLL control knob and BASS and FADE will display. Turn the TUNE/SCROLL control will display. Turn the TUNE/SCROLL control knob to knob to the left or right to adjust the sound level between the right or left to increase or decrease the bass tones.
Page 211 210 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following Program Type 16-Digit Character Display format types: Public Public Program Type 16-Digit Character Display Rhythm and Blues R & B No program type or Religious Music Rel Musc None undefined...
Page 212 UNDERSTANDING YOUR INSTRUMENT PANEL 211 • DISC Play/Pause - You can toggle between station with the same selected Music Type name. The Music Type function only operates when in the FM playing the DVD and pausing the DVD by mode. pushing the SELECT button (if equipped).
Page 213 212 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: TUNE/SCROLL control knob to adjust the minutes. • The available selections for each of the above entries Press the TUNE/SCROLL control knob again to save varies depending upon the disc. changes. • These selections can only be made while playing a •...
Page 214 UNDERSTANDING YOUR INSTRUMENT PANEL 213 down and selecting other. Enter the country code using Aspect Ratio — If Equipped the TUNE/SCROLL control knob to scroll up and down Selecting this item allows you to choose between wide to select the number and then push to select. screen, pan scan, and letter box.
Page 215: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play, Dvd-Video)
214 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button — To Set the Pushbutton Memory Every time a preset button is used, a corresponding When you are receiving a station that you wish to button number will display. commit to pushbutton memory, press the SET button. Buttons 1 - 6 The symbol SET 1 will now show in the display window.
Page 216 UNDERSTANDING YOUR INSTRUMENT PANEL 215 Radio display will show LOADING DISC when the disc CAUTION! is loading and “READING DISC” when the radio is reading the disc. The radio may shut down during extremely hot conditions. When this occurs, the radio will indicate CAUTION! “Disc Hot”...
Page 217: Notes On Playing Mp3/Wma Files
216 UNDERSTANDING YOUR INSTRUMENT PANEL The disc can be ejected with the radio and ignition OFF. RW/FF (CD MODE) Press and hold FF (Fast Forward) and the CD player will SEEK Button (CD MODE) begin to fast forward until FF is released, or RW or Press the right SEEK button for the next selection on the another CD button is pressed.
Page 218 UNDERSTANDING YOUR INSTRUMENT PANEL 217 Supported Medium Formats (File Systems) Multisession disc formats are supported by the radio. The medium formats supported by the radio are ISO 9660 Multisession discs may contain combinations of normal Level 1 and Level 2 and includes the Joliet extension. CD audio tracks and computer files (including MP3/ When reading discs recorded using formats other than WMA files).
Page 219 218 UNDERSTANDING YOUR INSTRUMENT PANEL frequencies in the following table are supported. In ID3 Tag information for artist, song title, and album title addition, variable bit rates (VBR) are also supported. The are supported for ID3 version 1 tags. ID3 version 2 is not majority of MP3/WMA files use a 44.1 kHz sampling rate supported by the radios.
Page 220: List Button (Disc Mode For Mp3/Wma Play)
UNDERSTANDING YOUR INSTRUMENT PANEL 219 • Number of files and folders - Loading times will INFO Button (DISC Mode for MP3/WMA Play) increase with more files and folders Pressing the INFO button repeatedly will scroll through the following TAG information: Song Title, Artist, File To increase the speed of disc loading, it is recommended Name, and Folder Name (if available).
Page 221 220 UNDERSTANDING YOUR INSTRUMENT PANEL Pressing the AUX button will change the mode to auxil- TIME Button (Auxiliary Mode) iary device if the AUX jack is connected. Press the TIME button to change the display from elapsed playing time to time of day. The time of day will NOTE: The AUX device must be turned on and the display for five seconds.
Page 222: Media Center 730N/430 (Rer/Ren/Rbz) - Am/Fm Stereo Radio And Cd/Dvd/Hdd/Nav - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 221 Operating Instructions - Uconnect™ Phone Macrovision (If Equipped) This product incorporates copyright protection technol- Refer to “Uconnect™ Phone” in “Understanding The ogy that is protected by U.S. patents and other intellec- Features Of Your Vehicle”. tual property rights.
Page 223: Operating Instructions - Voice Command System - If Equipped
222 UNDERSTANDING YOUR INSTRUMENT PANEL The REN, RER and RBZ radios contain a CD/DVD Clock Setting Procedure — RBZ Radio player, USB port, and a 30-gigabyte hard drive (HDD). To Manually Set the Clock Sirius Satellite Radio is optional. The 6.5 in (16.5 cm) touch screen allows for easy menu selection.
Page 224 UNDERSTANDING YOUR INSTRUMENT PANEL 223 5. To save the new time setting, touch the screen where Show Time if Radio is Off the word “Save” is displayed. When selected, this feature will display the time of day on the touch screen when the radio is turned off. Proceed Changing Daylight Savings Time as follows to change the current setting: When selected, this feature will display the time of day in...
Page 225: Clock Setting Procedure - Rer/Ren Radio
224 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Touch the screen where the words “Set Time Zone” are To Manually Set the Clock — RER/REN displayed. The time zone selection menu will appear on 1. Turn on the radio. the screen. 2. Touch the screen where the time is displayed. 4.
Page 226 UNDERSTANDING YOUR INSTRUMENT PANEL 225 6. To save the new time setting, touch the screen where Show Time if Radio is Off the word “Save” is displayed. When selected, this feature will display the time of day on the touch screen when the radio is turned off. Proceed Changing Daylight Savings Time as follows to change the current setting: When selected, this feature will display the time of day in...
Page 227: Media Center 130 (Res) - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
226 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Touch the screen where “User Clock” is displayed, the clock setting menu will appear on the screen. 4. Touch the screen where the words “Set Time Zone” are displayed. The time zone selection menu will appear on the screen.
Page 228 UNDERSTANDING YOUR INSTRUMENT PANEL 227 Power Switch/Volume Control (Rotary) TIME Button Push the ON/VOLUME control knob to turn on the Press the TIME button to alternate display of the time radio. Push the ON/VOLUME control knob a second and radio frequency. time to turn off the radio.
Page 229 228 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Push the rotary TUNE/SCROLL control knob a third Pressing the RW (Rewind) or FF (Fast Forward) buttons time and TREBLE will display. Turn the TUNE/SCROLL causes the tuner to search for the next frequency in the control knob to the right or left to increase or decrease the direction of the arrows.
Page 230: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 229 SET/RND Button — To Set the Pushbutton Every time a preset button is used, a corresponding Memory button number will display. When you are receiving a station that you wish to Buttons 1 - 6 commit to pushbutton memory, press the SET/RND These buttons tune the radio to the stations that you button.
Page 231 230 UNDERSTANDING YOUR INSTRUMENT PANEL • This radio is capable of playing compact discs (CD), CAUTION! recordable compact discs (CD-R), rewritable compact • This CD player will accept 4-3/4 in (12 cm) discs discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks.
Page 232 UNDERSTANDING YOUR INSTRUMENT PANEL 231 If you have ejected a disc and have not removed it within RW/FF 10 seconds, it will be reloaded. If the CD is not removed, Press and hold the FF (Fast Forward) button and the CD the radio will reinsert the CD but will not play it.
Page 233: Notes On Playing Mp3 Files
232 UNDERSTANDING YOUR INSTRUMENT PANEL Notes on Playing MP3 Files The radio uses the following limits for file systems: The radio can play MP3 files; however, acceptable MP3 • Maximum number of folder levels: 8 file recording media and formats are limited. When •...
Page 234 UNDERSTANDING YOUR INSTRUMENT PANEL 233 Multisession disc formats are supported by the radio. rates (VBR) are also supported. The majority of MP3 files Multisession discs may contain combinations of normal use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or CD audio tracks and computer files (including MP3 files).
Page 235: Operation Instructions - Auxiliary Mode
234 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files Operation Instructions - Auxiliary Mode When a medium containing MP3 data is loaded, the The auxiliary (AUX) jack is an audio input jack, which radio checks all files on the medium. If the medium allows the user to plug in a portable device, such as an contains a lot of folders or files, the radio will take more MP3 player, or cassette player, and utilize the vehicle’s...
Page 236: Media Center 130 (Res/Rsc) - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack) And Sirius Radio
UNDERSTANDING YOUR INSTRUMENT PANEL 235 MEDIA CENTER 130 (RES/RSC) — AM/FM Operating Instructions — Radio Mode STEREO RADIO WITH CD PLAYER NOTE: The ignition switch must be in the ON or ACC (MP3 AUX JACK) AND SIRIUS RADIO position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate.
Page 237 236 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio Phone Button Uconnect™ Phone — If Equipped will remain tuned to the new station until you make Press this button to operate the Uconnect™ Phone feature another selection.
Page 238 UNDERSTANDING YOUR INSTRUMENT PANEL 237 3. After adjusting the hours, press the right side TUNE/ INFO Button SCROLL control knob to set the minutes. The minutes Press the INFO button for an RDS station (one with call will begin to blink. letters displayed).
Page 239 238 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second MUSIC TYPE Button time and MID will display. Turn the TUNE/SCROLL Pressing this button once will turn on the Music Type control knob to the right or left to increase or decrease the mode for five seconds.
Page 240 UNDERSTANDING YOUR INSTRUMENT PANEL 239 Program Type 16-Digit Character Display Program Type 16-Digit Character Display Information Inform Top 40 Top 40 Jazz Jazz Weather Weather News News By pressing the SEEK button when the Music Type icon Nostalgia Nostalga is displayed, the radio will be tuned to the next frequency Oldies Oldies station with the same selected Music Type name.
Page 241 240 UNDERSTANDING YOUR INSTRUMENT PANEL hours, press the TUNE/SCROLL control knob to set You may add a second station to each pushbutton by the minutes. The minutes will begin to blink. Adjust repeating the above procedure with this exception: Press the minutes using the right side TUNE/SCROLL the SET/RND button twice and SET 2 will show in the control knob.
Page 242: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
UNDERSTANDING YOUR INSTRUMENT PANEL 241 Operation Instructions — CD MODE for CD and If you insert a disc with the ignition ON and the radio MP3 Audio Play ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will NOTE: show the track number, and index time in minutes and •...
Page 243 242 UNDERSTANDING YOUR INSTRUMENT PANEL EJECT Button - Ejecting a CD the current selection. Pressing and holding the SEEK Press the EJECT button to eject the CD. button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD If you have ejected a disc and have not removed it within...
Page 244: Notes On Playing Mp3 Files
UNDERSTANDING YOUR INSTRUMENT PANEL 243 SET/RND Button (Random Play Button) Supported Medium Formats (File Systems) Press this button while the CD is playing to activate The medium formats supported by the radio are ISO 9660 Random Play. This feature plays the selections on the Level 1 and Level 2 and includes the Joliet extension.
Page 245 244 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of characters in file/folder names: extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will • Level 1: 12 (including a separator . and a three- not play the file.
Page 246: List Button (Cd Mode For Mp3 Play)
UNDERSTANDING YOUR INSTRUMENT PANEL 245 • Number of files and folders - Loading times will ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not increase with more files and folders supported by the radios.
Page 247: Info Button (Cd Mode For Mp3 Play)
246 UNDERSTANDING YOUR INSTRUMENT PANEL INFO Button (CD Mode for MP3 Play) Pressing the AUX button will change the mode to auxil- Pressing the INFO button repeatedly will scroll through iary device if the AUX jack is connected. the following TAG information: Song Title, Artist, File NOTE: The AUX device must be turned on and the Name, and Folder Name (if available).
Page 248: Universal Consumer Interface (Uci) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 247 UNIVERSAL CONSUMER INTERFACE (UCI) — IF NOTE: • If the radio has a USB port, connecting an iPod to this EQUIPPED port does not play the media. For playing an iPod , NOTE: This section is for sales code RES and REQ/ use the separate 16–pin connector port (in the glove REL/RET radios only with uconnect™.
Page 249: Using This Feature
248 UNDERSTANDING YOUR INSTRUMENT PANEL • The iPod battery charges when plugged into the UCI NOTE: • You may have to remove the connector pin protection connector (if supported by the specific iPod device) cap from the 16–pin connector port, prior to connect- Controlling The iPod Using Radio Buttons ing the cable.
Page 250 UNDERSTANDING YOUR INSTRUMENT PANEL 249 • Turning it counterclockwise (backward) by one jump to the previous track in the list; if you press this click, during the first two seconds of the track, will button at any other time in the track, it will jump to the jump to the previous track in the list.
Page 251: List Or Browse Mode
250 UNDERSTANDING YOUR INSTRUMENT PANEL During Scan mode, you can also press the << SEEK the track to be played highlighted on the radio and SEEK >> buttons to select the previous and next display, press the TUNE control knob to select and tracks.
Page 252 UNDERSTANDING YOUR INSTRUMENT PANEL 251 • Preset 5 – Audiobooks • MUSIC TYPE button: The MUSIC TYPE button is another shortcut button to the genre listing on your • Preset 6 – Podcasts iPod . • Pressing a PRESET button will display the current CAUTION! list on the top line and the first item in that list on the second line.
Page 253: Understanding Your Instrument Panel
252 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect™ Multimedia (SATELLITE RADIO) — IF information, call the toll-free number 888-539-7474, or EQUIPPED (REN/REQ/RER/RES/REU/RBZ visit the Sirius web site at www.sirius.com, or at www- .siriuscanada.ca for Canadian residents. RADIOS ONLY) Satellite radio uses direct satellite-to-receiver broadcast- Electronic Serial Number/Sirius Identification ing technology to provide clear digital sound, coast to Number (ESN/SID)
Page 254: Selecting Uconnect™ Multimedia (Satellite) Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 253 Sirius ID number will display. The Sirius ID number Selecting Uconnect™ Multimedia (Satellite) Mode display will time out in two minutes. Press any button on Press the SAT button until SAT appears in the display. A the radio to exit this screen.
Page 255: Operating Instructions - Uconnect™ Multimedia (Satellite) Mode
254 UNDERSTANDING YOUR INSTRUMENT PANEL • Dense tree coverage may interrupt reception in the SCAN Button (When Equipped) form of short audio mutes. Pressing the SCAN button causes the tuner to search for the next channel, pausing for eight seconds before con- •...
Page 256 UNDERSTANDING YOUR INSTRUMENT PANEL 255 RW/FF By pressing the SEEK button when the Music Type Pressing the RW (Rewind) or FF (Fast Forward) buttons function is active, the radio will be tuned to the next causes the tuner to search for the next channel in the channel with the same selected Music Type name.
Page 257 256 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button You may add a second channel to each pushbutton by Pressing the SETUP button allows you to select the repeating the above procedure with this exception: Press following items: the SET button twice and SET 2 will show in the display window.
Page 258: Operating Instructions - Uconnect™ Phone (If Equipped)
UNDERSTANDING YOUR INSTRUMENT PANEL 257 Operating Instructions — Uconnect™ Phone (If Equipped) Refer to “Uconnect™ Phone” in “Understanding The Features Of Your Vehicle”. Operating Instructions — Video Entertainment System (VES)™ (If Equipped) Refer to separate “Video Entertainment System (VES)™ Guide.” REMOTE SOUND SYSTEM CONTROLS —...
Page 259: Radio Operation
258 UNDERSTANDING YOUR INSTRUMENT PANEL The button located in the center of the right-hand control beginning of the current track or to the beginning of the will switch modes to Radio or CD. previous track, if it is within one second after the current track begins to play.
Page 260: Radio Operation And Cellular Phones
UNDERSTANDING YOUR INSTRUMENT PANEL 259 3. Do not apply paper or tape to the disc; avoid scratch- RADIO OPERATION AND CELLULAR PHONES ing the disc. Under certain conditions, the cellular phone being on in your vehicle can cause erratic or noisy performance from 4.
Page 261: Manual Heating And Air Conditioning
260 UNDERSTANDING YOUR INSTRUMENT PANEL Manual Heating and Air Conditioning Blower Control Rotate this control to regulate the amount of air forced through the ven- tilation system in any mode. The blower speed increases as you move the control to the right from the “O” (OFF) position.
Page 262 UNDERSTANDING YOUR INSTRUMENT PANEL 261 Temperature Control Mode Control (Air Direction) Rotate this control to regulate the tem- Rotate this control to choose from sev- perature of the air inside the passenger eral patterns of air distribution. You compartment. Rotating the dial left can select either a primary mode as into the blue area of the scale indicates identified by the symbols on the con-...
Page 263 262 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: For all settings except full cold or full hot, there Defrost is a difference in temperature between the upper and Air is directed through the windshield and side lower outlets. The warmer air flows to the floor outlets. window demist outlets.
Page 264 UNDERSTANDING YOUR INSTRUMENT PANEL 263 NOTE: Air Conditioning Control • Continuous use of the recirculation mode may make Press this button to engage the Air the inside air stuffy and window fogging may occur. Conditioning. A light will illuminate Extended use of this mode is not recommended. when the Air Conditioning System is engaged.
Page 265: Automatic Temperature Control (Atc) - If Equipped
264 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Temperature Control (ATC) — Automatic Operation If Equipped Operation of the system is quite simple. The Automatic Temperature Control system automati- 1. Turn the Mode Control knob (on the right) and the cally maintains the climate in the cabin of the vehicle at Blower Control knob (on the left) to AUTO.
Page 266 UNDERSTANDING YOUR INSTRUMENT PANEL 265 • Pressing the Air Conditioning Control button while in You will experience the greatest efficiency by simply allowing the system to function automatically. Selecting AUTO mode will cause the LED in the control button the “O” (OFF) position on the blower control stops the to flash three times and then turn off.
Page 267 266 UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control Manual Operation For full automatic operation or for This system offers a full complement of manual override automatic blower operation turn the features, which consist of Blower Preferred Automatic, knob to AUTO position. In manual Mode Preferred Automatic, or Blower and Mode Pre- mode there are seven blower speeds ferred Automatic.
Page 268 UNDERSTANDING YOUR INSTRUMENT PANEL 267...
Page 269 268 UNDERSTANDING YOUR INSTRUMENT PANEL • Floor The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and side window demist outlets.
Page 270 UNDERSTANDING YOUR INSTRUMENT PANEL 269 • Air Conditioner Control NOTE: • When the ignition switch is turned to the LOCK Press this button to turn on the air conditioning during manual operation position, the recirculation feature will be cancelled. only. When the air conditioning is •...
Page 271: Operating Tips
270 UNDERSTANDING YOUR INSTRUMENT PANEL • Most of the time, when in Automatic Operation, you Summer Operation can temporarily put the system into Recirculation The engine cooling system in air-conditioned vehicles Mode by pressing the Recirculation button. However, must be protected with a high-quality antifreeze coolant under certain conditions, while in Automatic Mode, to provide proper corrosion protection and to protect the system is blowing air out the defrost vents.
Page 272 UNDERSTANDING YOUR INSTRUMENT PANEL 271 Window Fogging Outside Air Intake Interior fogging on the windshield can be quickly re- Make sure the air intake, located directly in front of the moved by turning the mode selector to Defrost. The windshield, is free of obstructions such as leaves. Leaves Defrost/Floor mode can be used to maintain a clear collected in the air intake may reduce airflow, and if they windshield and provide sufficient heating.
Page 273 272 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions...
Page 274: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....277 Manual Transaxle — If Equipped ..280 Manual Transaxle –...
Page 275 274 STARTING AND OPERATING AutoStick — If Equipped ....285 Parking Brake ......293 Operation .
Page 276 STARTING AND OPERATING 275 Tire Identification Number (TIN) ..311 Tire Chains ......324 Tire Terminology And Definitions .
Page 277 276 STARTING AND OPERATING Fuel System Cautions ....338 Trailer Towing Weights (Maximum Trailer Weight Ratings) ..347 Carbon Monoxide Warnings .
Page 278: Starting Procedures
STARTING AND OPERATING 277 STARTING PROCEDURES NOTE: • The engine will not start unless the clutch pedal is Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. pressed to the floor. •...
Page 279: Normal Starting
278 STARTING AND OPERATING Do not press the accelerator. Turn the ignition switch to WARNING! the START position and release it as soon as the starter engages. The starter motor will continue to run, and it Do not attempt to push or tow your vehicle to get it will disengage automatically when the engine is running.
Page 280: If Engine Fails To Start
STARTING AND OPERATING 279 If Engine Fails to Start CAUTION! If the engine fails to start after you have followed the “Normal Starting” and “Extreme Cold Weather” proce- To prevent damage to the starter, do not crank the dures, it may be flooded. Push the accelerator pedal all engine for more than 15 seconds at a time.
Page 281: Manual Transaxle - If Equipped
280 STARTING AND OPERATING Fully press the clutch pedal before you shift gears. As you WARNING! release the clutch pedal, lightly press the accelerator pedal. Remember to disconnect the cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution.
Page 282: Recommended Shift Speeds
STARTING AND OPERATING 281 Use each gear in numerical order, do not skip a gear. Be Recommended Shift Speeds sure the transaxle is in first gear, (not third), when To use your manual transaxle for optimal fuel economy, starting from a standing position. Damage to the clutch it should be upshifted as listed in the following table.
Page 283: Automatic Transaxle - If Equipped
282 STARTING AND OPERATING CAUTION! CAUTION! If you skip more than one gear while downshifting Damage to the transaxle may occur if the following or downshift at too high a vehicle speed, you could precautions are not observed: • Shift into PARK only after the vehicle has come to damage the engine, transmission, or clutch.
Page 284: Brake/Transmission Interlock System
STARTING AND OPERATING 283 NOTE: If a malfunction occurs, the transaxle will not WARNING! shift out of PARK. Battery power is required to release the brake/transmission interlock system. There is a remov- It is dangerous to move the shift lever out of PARK or able plug in the right side of the shift lever housing that NEUTRAL if the engine speed is higher than idle allows you to insert your finger to override the system.
Page 285: Gear Ranges
284 STARTING AND OPERATING Gear Ranges WARNING! DO NOT race the engine when shifting from PARK or NEUTRAL positions into another gear range. Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, PARK you should never exit a vehicle while the engine is This range supplements the parking brake by locking the...
Page 286: Autostick - If Equipped
STARTING AND OPERATING 285 • Look at the shift indicator window on the shift lever NEUTRAL bezel to ensure it is in the PARK position. This range is used when the vehicle is standing for prolonged periods with the engine running. The engine •...
Page 287: Operation
286 STARTING AND OPERATING engine from overspeed. Changes down will only happen AutoStick is deactivated: at minimum engine speed to prevent stalling. • By holding the shift lever to (+) momentarily Operation • When the shift lever is shifted out of DRIVE NOTE: AutoStick is not functional until the CVT...
Page 288: Four-Wheel Drive Operation - If Equipped
STARTING AND OPERATING 287 • If a downshift would cause the engine to overspeed, that shift will not occur until it is safe for the engine. However. the CVT will stay in the manually selected ratio. • If the system detects powertrain overheating, the transmission will revert to the automatic shift mode and remain in that mode until the powertrain cools off.
Page 289: Driving On Slippery Surfaces
288 STARTING AND OPERATING cluster. This can be done on the fly, at any vehicle speed. WARNING! To deactivate, simply pull on the switch one more time. The “4WD Indicator Light” will then go out. Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the NOTE: Refer to “Electronic Brake Control System/...
Page 290: Driving Through Water
STARTING AND OPERATING 289 2. Slow down if the road has standing water or puddles. Flowing/Rising Water 3. Replace the tires when tread wear indicators first WARNING! become visible. Do not drive on or across a road or path where water 4.
Page 291 290 STARTING AND OPERATING CAUTION! CAUTION! (Continued) • Driving through standing water may cause dam- • Always check the depth of the standing water age to your vehicle’s drivetrain components. Al- before driving through it. Never drive through ways inspect your vehicle’s fluids (i.e., engine oil, standing water that is deeper than the bottom of transmission/transaxle, axle, etc.) for signs of con- the tire rims mounted on the vehicle.
Page 292: On-Road Driving Tips
STARTING AND OPERATING 291 ON-ROAD DRIVING TIPS WARNING! Utility vehicles have higher ground clearance and a • Driving through standing water limits your vehi- narrower track to make them capable of performing in a wide variety of off-road applications. Specific design cle’s traction capabilities.
Page 293 292 STARTING AND OPERATING in tight spaces. The system will provide mechanical WARNING! steering capability if power assist is lost. Continued operation with reduced power steering If for some reason the power assist is interrupted, it will assist could pose a safety risk to yourself and others. still be possible to steer your vehicle.
Page 294: Power Steering Fluid Check
STARTING AND OPERATING 293 Power Steering Fluid Check WARNING! Checking the power steering fluid level at a defined service interval is not required. The fluid should only be Fluid level should be checked on a level surface and checked if a leak is suspected, abnormal noises are with the engine off to prevent injury from moving apparent, and/or the system is not functioning as antici- parts and to ensure accurate fluid level reading.
Page 295 294 STARTING AND OPERATING The parking brake lever is located in the center console. When the parking brake is applied with the ignition To apply the parking brake, pull the lever up as firmly as switch in the ON position, the “Brake Warning Light” in possible.
Page 296 STARTING AND OPERATING 295 to move the shift lever out of PARK. The parking brake WARNING! (Continued) should always be applied whenever the driver is not in • Always fully apply the parking brake when leav- the vehicle. ing your vehicle or it may roll and cause damage or injury.
Page 297: Brake System
296 STARTING AND OPERATING BRAKE SYSTEM If either of the two hydraulic systems lose normal capa- Your vehicle is equipped with power assisted brakes as bility, the remaining system will still function with some standard equipment. In the event power assist is lost for loss of overall braking effectiveness.
Page 298: Anti-Lock Brake System (Abs)
STARTING AND OPERATING 297 Anti-Lock Brake System (ABS) WARNING! (Continued) The ABS provides increased vehicle stability and brake • The ABS cannot prevent accidents, including performance under most braking conditions. The system those resulting from excessive speed in turns, automatically “pumps” the brakes during severe braking following another vehicle too closely, or hydro- conditions to prevent wheel lock-up.
Page 299 298 STARTING AND OPERATING required. However, the conventional brake system will working properly. This self-check occurs each time the continue to operate normally if the “Brake Warning vehicle is started and accelerated past 7 mph (11 km/h). Light” is not on. ABS is activated during braking under certain road or If the “ABS Warning Light”...
Page 300: Electronic Brake Control System
STARTING AND OPERATING 299 (TCS), Brake Assist System (BAS), Electronic Roll Mitiga- WARNING! tion (ERM), Hill Start Assist (HSA), and Electronic Sta- bility Control (ESC). All systems work together to en- The Anti-Lock Brake System (ABS) contains sophis- hance vehicle stability and control in various driving ticated electronic equipment that may be susceptible conditions and are commonly referred to as ESC.
Page 301: Brake Assist System (Bas)
300 STARTING AND OPERATING slip differential and controls the wheel spin across a “pump” the brakes). Do not reduce brake pedal pressure driven axle. If one wheel on a driven axle is spinning unless braking is no longer desired. Once the brake pedal faster than the other, the system will apply the brake of is released, the BAS is deactivated.
Page 302: Electronic Roll Mitigation (Erm)
STARTING AND OPERATING 301 Electronic Roll Mitigation (ERM) NOTE: Anytime the ESC system is in the “Full Off” This system anticipates the potential for wheel lift by mode, ERM is disabled. Refer to “Electronic Stability monitoring the driver’s steering wheel input and the Control (ESC)”...
Page 303: Hill Start Assist (Hsa) - Manual Transaxle Only
302 STARTING AND OPERATING • Gear selection matches vehicle uphill direction (i.e., Hill Start Assist (HSA) – Manual Transaxle Only The HSA system is designed to assist the driver when vehicle facing uphill is in forward gear; vehicle back- starting a vehicle from a stop on a hill. HSA will maintain ing uphill is in REVERSE gear).
Page 304: Electronic Stability Control (Esc)
STARTING AND OPERATING 303 For vehicles not equipped with the EVIC, perform the 8. Rotate the steering wheel back to center and then an following steps: additional half-turn to the right. NOTE: You must complete Steps 1 through 8 within 9.
Page 305 304 STARTING AND OPERATING driver and compares it to the actual path of the vehicle. WARNING! When the actual path does not match the intended path, • The Electronic Stability Control (ESC) cannot pre- ESC applies the brake of the appropriate wheel to assist in counteracting the over-steer or under-steer condition vent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by...
Page 306 STARTING AND OPERATING 305 • The ESC system will make buzzing or clicking sounds ESC Malfunction Indicator Light The “ESC Malfunction Indicator Light” in the when it is active. This is normal; the sounds will stop instrument cluster will come on when the when ESC becomes inactive following the maneuver ignition switch is turned to the ON position.
Page 307 306 STARTING AND OPERATING Partial Off (Four-Wheel Drive Models) or On mode by pressing the “ESC Off” switch. Once the situa- (Two-Wheel Drive Models) tion requiring ESC to be switched to the “Partial Off” This mode is entered by momentarily pressing the “ESC mode is overcome, turn ESC back on by momentarily Off”...
Page 308 STARTING AND OPERATING 307 the vehicle reaches a speed of 35 mph (56 km/h). At WARNING! 35 mph (56 km/h) the system returns to “Partial Off” mode, as described above. TCS remains off. When the With the ESC switched off, the enhanced vehicle vehicle speed drops below 30 mph (48 km/h) the ESC stability offered by ESC is unavailable.
Page 309: Tire Safety Information
308 STARTING AND OPERATING TIRE SAFETY INFORMATION NOTE: • P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 310 STARTING AND OPERATING 309 • High flotation tire sizing is based on U.S. design Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designa- standards and it begins with the tire diameter molded tion.
Page 311 310 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 312: Tire Identification Number (Tin)
STARTING AND OPERATING 311 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
Page 313: Tire Terminology And Definitions
312 STARTING AND OPERATING Tire Terminology and Definitions Term Definition B-Pillar The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold Tire Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
Page 314: Tire Loading And Tire Pressure
STARTING AND OPERATING 313 Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard Tire Placard Location...
Page 315 314 STARTING AND OPERATING axles must not be exceeded. For further information on This placard tells you important information about GAWRs, vehicle loading, and trailer towing, refer to the: “Vehicle Loading” in this section. 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of...
Page 316 STARTING AND OPERATING 315 3. Subtract the combined weight of the driver and pas- NOTE: • The following table shows examples on how to calcu- sengers from XXX lbs or XXX kg. late total load, cargo/luggage, and towing capacities 4. The resulting figure equals the available amount of of your vehicle with varying seating configurations cargo and luggage load capacity.
Page 317 316 STARTING AND OPERATING...
Page 318: Tires - General Information
STARTING AND OPERATING 317 Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause accidents. recommended load capacity for your vehicle.
Page 319: Tire Inflation Pressures
318 STARTING AND OPERATING Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the • Unequal tire pressures from one side of the ve- driver’s side “B” Pillar. hicle to the other can cause the vehicle to drift to Some vehicles may have Supplemental Tire Pressure the right or left.
Page 320: Tire Pressures For High Speed Operation
STARTING AND OPERATING 319 Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, al- the Winter.
Page 321: Radial Ply Tires
320 STARTING AND OPERATING loading may be required for high-speed vehicle opera- Radial Ply Tires tion. Refer to original equipment or an authorized tire WARNING! dealer for recommended safe operating speeds, loading and cold tire inflation pressures. Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle WARNING! poorly.
Page 322: Tire Spinning
STARTING AND OPERATING 321 WARNING! CAUTION! • Temporary use spare tires are for emergency use Because of the reduced ground clearance, do not take only. With these tires, do not drive more than your vehicle through an automatic car wash with the 50 mph (80 km/h).
Page 323: Tread Wear Indicators
322 STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the...
Page 324: Life Of Tire
STARTING AND OPERATING 323 Life of Tire Replacement Tires The service life of a tire is dependent upon varying The tires on your new vehicle provide a balance of many factors including, but not limited to: characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
Page 325: Tire Chains
324 STARTING AND OPERATING WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 326: Snow Tires
STARTING AND OPERATING 325 TIRE ROTATION RECOMMENDATIONS CAUTION! Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, Damage to the vehicle may result if tire chains are and braking functions. For these reasons, they wear at used.
Page 327: Tire Pressure Monitoring System (Tpms)
326 STARTING AND OPERATING The suggested rotation method is shown in the following The tire pressure will vary with temperature by about diagram. 1 psi (6.9 kPa) for every 12°F (6.5°C). This means that when the outside temperature decreases, the tire pressure will decrease.
Page 328 STARTING AND OPERATING 327 The TPMS will continue to warn the driver of low tire For example, your vehicle may have a recommended pressure as long as the condition exists, and will not turn cold (parked for more than three hours) placard pressure off until the tire pressure is at or above the recommended of 30 psi (207 kPa).
Page 329 328 STARTING AND OPERATING NOTE: CAUTION! • The TPMS is not intended to replace normal tire care • The TPMS has been optimized for the original and maintenance or to provide warning of a tire failure or condition. equipment tires and wheels. TPMS pressures and warnings have been established for the tire size •...
Page 330: Base System
STARTING AND OPERATING 329 • Seasonal temperature changes will affect tire pressure, • Four Tire Pressure Monitoring Sensors and the TPMS will monitor the actual tire pressure in • Tire Pressure Monitoring Telltale Light the tire. Tire Pressure Monitoring Low Pressure Warnings Base System The Tire Pressure Monitoring Telltale Light will illumi- This is the TPMS warning indicator located in the...
Page 331 330 STARTING AND OPERATING fault is detected. The system fault will also sound a 1. The compact spare tire does not have a tire pressure chime. If the ignition key is cycled, this sequence will monitoring sensor. Therefore, the TPMS will not monitor repeat providing the system fault still exists.
Page 332: Premium System - If Equipped
STARTING AND OPERATING 331 5. Once you repair or replace the original road tire and The TPMS consists of the following components: reinstall it on the vehicle in place of the compact spare • Receiver Module tire, the TPMS will update automatically and the Tire •...
Page 333 332 STARTING AND OPERATING every ignition cycle for each condition that it detects. In display to the vehicle’s recommended cold placard pres- addition, the EVIC will display a graphic of the pressure sure value. The system will automatically update, the value(s) with the low tire(s) flashing.
Page 334 STARTING AND OPERATING 333 will be displayed instead of dashes. A system fault can occur with any of the following scenarios: 1. Jamming due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors.
Page 335: General Information
334 STARTING AND OPERATING 2. If you install the compact spare tire in place of a road 5. Once you repair or replace the original road tire and tire that has a pressure below the low-pressure warning reinstall it on the vehicle in place of the compact spare limit, upon the next ignition key cycle, a chime will tire, the TPMS will update automatically and the Tire sound and the Tire Pressure Monitoring Telltale Light...
Page 336: Fuel Requirements
STARTING AND OPERATING 335 The tire pressure sensors are covered under one of the Poor quality gasoline can cause problems such as hard following licenses: starting, stalling and hesitations. If you experience these symptoms, try another brand of gasoline (with the ap- propriate octane rating for your engine) before consider- United States .
Page 337: Gasoline/Oxygenate Blends
336 STARTING AND OPERATING Gasoline/Oxygenate Blends E85 Usage In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxy- Non-FFV vehicles are compatible with gasoline contain- genates such as 10% ethanol, MTBE, and ETBE. Oxygen- ing 10% ethanol (E10). Gasoline with higher ethanol ates are required in some areas of the country during the content may void the vehicle’s warranty.
Page 338: Mmt In Gasoline
STARTING AND OPERATING 337 • disconnect and reconnect the battery to reset the It is even more important to look for gasoline without engine controller memory MMT in Canada, because MMT can be used at levels higher than those allowed in the United States. More extensive repairs will be required for prolonged exposure to E85 fuel.
Page 339 338 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) • The use of fuel additives, which are now being CAUTION! sold as octane enhancers, is not recommended. Follow these guidelines to maintain your vehicle’s Most of these products contain high concentra- performance: tions of Methanol.
Page 340: Carbon Monoxide Warnings
STARTING AND OPERATING 339 Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper WARNING! maintenance. Have the exhaust system inspected Carbon monoxide (CO) in exhaust gases is deadly. every time the vehicle is raised. Have any abnor- Follow the precautions below to prevent carbon mal conditions repaired promptly.
Page 341 340 STARTING AND OPERATING After removing the gas cap, place the gas cap tether cable CAUTION! over a hook on the inside of the fuel door. This keeps the • Damage to the fuel system or emission control gas cap suspended away from and protects the vehicle’s surface.
Page 342: Loose Fuel Filler Cap Message
STARTING AND OPERATING 341 Loose Fuel Filler Cap Message WARNING! (Continued) If the vehicle diagnostic system determines that the fuel • Never add fuel when the engine is running. This is filler cap is loose or improperly installed, a “gASCAP” in violation of most state and Federal fire regula- message will be displayed in the Odometer/Trip Odom- tions and may cause the MIL to turn on.
Page 343: Vehicle Certification Label
342 STARTING AND OPERATING Vehicle Certification Label Gross Vehicle Weight Rating (GVWR) Your vehicle has a Vehicle Certification Label attached to The GVWR is the total allowable weight of your vehicle. the driver’s door B-Pillar. This includes driver, passengers, and cargo. The total load must be limited so that you do not exceed the The label contains the following information: GVWR.
Page 344 STARTING AND OPERATING 343 Curb Weight Overloading can cause potential safety hazards and The curb weight of a vehicle is defined as the total weight shorten useful service life. Heavier suspension compo- of the vehicle with all fluids, including vehicle fuel, at full nents do not necessarily increase the vehicle’s GVWR.
Page 345: Trailer Towing
344 STARTING AND OPERATING TRAILER TOWING Gross Trailer Weight (GTW) In this section you will find safety tips and information The GTW is the weight of the trailer plus the weight of all on limits to the type of towing you can reasonably do cargo, consumables and equipment (permanent or tem- with your vehicle.
Page 346 STARTING AND OPERATING 345 that typically provides adjustable friction associated with WARNING! the telescoping motion to dampen any unwanted trailer swaying motions while traveling. It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition Weight-Carrying Hitch can result if either rating is exceeded.
Page 347: Trailer Hitch Classification
346 STARTING AND OPERATING safety. The addition of a friction/hydraulic sway control Refer to the Trailer Towing Weights (Maximum Trailer also dampens sway caused by traffic and crosswinds and Weight Ratings) chart for the maximum GTW towable for contributes positively to tow vehicle and trailer stability. your given drivetrain.
Page 348: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 347 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transaxle Frontal Area Max. GTW (Gross Trailer Wt.) Max. Tongue Wt. (See Note 1) 2.0L Auto/Man 22 sq ft (2.04 sq m) 1,000 lbs (450 kg) 150 lbs (50 kg)
Page 349: Towing Requirements
348 STARTING AND OPERATING • The weight of the driver and all passengers. Never exceed the maximum trailer tongue weight stamped on your bumper or trailer hitch. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or authorized dealer-installed options, must be considered as part of the total load on your vehicle.
Page 350 STARTING AND OPERATING 349 CAUTION! (Continued) WARNING! (Continued) • Then, during the first 500 miles (805 km) that a • Make certain that the load is secured in the trailer trailer is towed, do not drive over 50 mph and will not shift during travel. When trailering (80 km/h) and do not make starts at full throttle.
Page 351 350 STARTING AND OPERATING Towing Requirements – Tires WARNING! (Continued) − Do not attempt to tow a trailer while using a compact • Vehicles with trailers should not be parked on a spare tire. grade. When parking, apply the parking brake on the tow vehicle.
Page 352 STARTING AND OPERATING 351 replacement procedures. Replacing tires with a higher CAUTION! load carrying capacity will not increase the vehicle’s GVWR and GAWR limits. If the trailer weighs more than 1,000 lbs (454 kg) loaded, it should have its own brakes and they Towing Requirements –...
Page 353 352 STARTING AND OPERATING Towing Requirements – Trailer Lights and Wiring Your authorized dealer offers a trailer wiring harness designed specifically for your vehicle. Whenever you pull a trailer, regardless of the trailer size, stop lights and turn signals on the trailer are required for motoring safety.
Page 354: Towing Tips
STARTING AND OPERATING 353 Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Automatic Transaxle The automatic transaxle fluid and filter should be changed if you REGULARLY tow a trailer for more than 45 minutes of continuous operation.
Page 355 354 STARTING AND OPERATING Electronic Speed Control – If Equipped Cooling System To reduce the potential for engine and transaxle over- − Do not use in hilly terrain or with heavy loads. heating, take the following actions: − When using the speed control, if you experience speed −...
Page 356: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 355 RECREATIONAL TOWING NOTE: Vehicles equipped with manual transaxles may (BEHIND MOTORHOME, ETC.) be recreationally towed (flat towed) at any legal highway speed, for any distance, if the manual transaxle is in Towing This Vehicle Behind Another Vehicle (Flat NEUTRAL and the ignition key is in the ACC position.
Page 358: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....358 Jump-Starting Procedures ....366 If Your Engine Overheats .
Page 359: Hazard Warning Flasher
358 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel, below the radio. potential for overheating by taking the appropriate ac- tion.
Page 360 WHAT TO DO IN EMERGENCIES 359 • You can also turn the temperature control to maximum CAUTION! heat, the mode control to floor and the blower control to high. This allows the heater core to act as a Driving with a hot cooling system could damage supplement to the radiator and aids in removing heat your vehicle.
Page 361: Automatic Transaxle Overheating
360 WHAT TO DO IN EMERGENCIES AUTOMATIC TRANSAXLE OVERHEATING JACKING AND TIRE CHANGING During sustained high speed driving or trailer towing up WARNING! long grades on hot days, the automatic transaxle oil may become too hot. • Being under a jacked-up vehicle is dangerous. The If this happens, the transmission overheat in- vehicle could slip off the jack and fall on you.
Page 362: Jack Location
WHAT TO DO IN EMERGENCIES 361 Jack Location Spare Tire Removal The jack and jack-handle are stowed under the load floor Lift up the load floor cover and remove the hold down. in the cargo area. Preparations For Jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas.
Page 363: Jacking Instructions
362 WHAT TO DO IN EMERGENCIES 5. Turn on the Hazard Warning flasher. WARNING! (Continued) 6. Block both the front and rear of the • Always park on a firm, level surface as far from wheel diagonally opposite the jacking the edge of the roadway as possible before raising position.
Page 364 WHAT TO DO IN EMERGENCIES 363 2. Loosen, but do not remove, the wheel nuts by turning WARNING! (Continued) them to the left one turn while the wheel is still on the • If working on or near a roadway, be extremely ground.
Page 365 364 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Do not attempt to raise the vehicle by jacking on Raising the vehicle higher than necessary can make locations other than those indicated in Step 3. the vehicle less stable. It could slip off the jack and hurt someone near it.
Page 366 WHAT TO DO IN EMERGENCIES 365 9. Remove the wheel blocks and lower the jack until it is WARNING! free. Reassemble the lug wrench to the jack assembly and stow it in the spare tire area. Secure the assembly using To avoid possible personal injury, handle the wheel the means provided.
Page 367: Jump-Starting Procedures
366 WHAT TO DO IN EMERGENCIES 11. Check the tire pressure as soon as possible. Correct CAUTION! the tire pressure as required. Do not use a portable battery booster pack or any JUMP-STARTING PROCEDURES other booster source with a system voltage greater If your vehicle has a discharged battery it can be jump- than 12 Volts or damage to the battery, starter motor, started using a set of jumper cables and a battery in...
Page 368: Preparations For Jump-Start
WHAT TO DO IN EMERGENCIES 367 Preparations for Jump-Start The battery in your vehicle is located in the front of the engine compartment below the air intake duct. To access the battery remove the air intake duct by turning the two finger screws, located on the radiator support.
Page 369: Jump-Starting Procedure
368 WHAT TO DO IN EMERGENCIES 3. If using a another vehicle to jump-start the battery, WARNING! park the vehicle within the jumper cables reach, set the • Take care to avoid the radiator cooling fan when- parking brake and make sure the ignition is OFF. ever the hood is raised.
Page 370 WHAT TO DO IN EMERGENCIES 369 CAUTION! WARNING! Failure to follow these procedures could result in Do not connect the cable to the negative post (-) of the damage to the charging system of the booster vehicle discharged battery. The resulting electrical spark or the discharged vehicle.
Page 371: Freeing A Stuck Vehicle
370 WHAT TO DO IN EMERGENCIES 8. Disconnect the opposite end of the positive (+) jumper FREEING A STUCK VEHICLE cable from the positive (+) post of the booster battery. If your vehicle becomes stuck in mud, sand or snow, it can often be moved by a rocking motion.
Page 372: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 371 TOWING A DISABLED VEHICLE CAUTION! (Continued) With Ignition Key • Revving the engine or spinning the wheels too fast may lead to transmission overheating and failure. Automatic Transaxle It can also damage the tires. Do not spin the •...
Page 373 372 WHAT TO DO IN EMERGENCIES All Transaxles CAUTION! If it is necessary to use the accessories while being towed (wipers, defrosters, etc.), the key must be in the ON DO NOT flat tow any vehicle equipped with an position, not the ACC position. Make certain the trans- automatic transmission.
Page 374: Without The Ignition Key
WHAT TO DO IN EMERGENCIES 373 Without The Ignition Key Battery power is required to release the brake/ Special care must be taken when the vehicle is towed transmission interlock system (automatic transmission with the ignition in the LOCK position. A dolly should be only).
Page 376: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment — 2.0L ... . . 377 Maintenance Procedures ....382 Engine Compartment —...
Page 377 376 MAINTAINING YOUR VEHICLE Exhaust System ..... 391 Replacement Bulbs ....412 Cooling System .
Page 378: Engine Compartment - 2.0L
MAINTAINING YOUR VEHICLE 377 ENGINE COMPARTMENT — 2.0L 1 — Washer Fluid Reservoir 6 — Integrated Power Module 2 — Power Steering Fluid Reservoir 7 — Battery (Under Cover) 3 — Engine Oil Fill 8 — Coolant Pressure Cap 4 — Air Cleaner Filter 9 —...
Page 379: Engine Compartment - 2.4L
378 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.4L 1 — Washer Fluid Reservoir 6 — Battery (Under Cover) 2 — Power Steering Fluid Reservoir 7 — Air Cleaner Filter 3 — Engine Oil Fill 8 — Coolant Pressure Cap 4 — Brake Fluid Reservoir 9 —...
Page 380: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 379 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated Onboard • Prolonged driving with the MIL on could cause Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic further damage to the emission control system.
Page 381: Emissions Inspection And Maintenance Programs
380 MAINTAINING YOUR VEHICLE persists, the message will appear the next time the Normally, the OBD II system will be ready. The OBD II vehicle is started. This might indicate a damaged cap. If system may not be ready if your vehicle was recently the problem is detected twice in a row, the system will serviced, recently had a dead battery or a battery replace- turn on the MIL.
Page 382: Replacement Parts
MAINTAINING YOUR VEHICLE 381 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced a.
Page 383: Dealer Service
382 MAINTAINING YOUR VEHICLE DEALER SERVICE MAINTENANCE PROCEDURES Your authorized dealer has the qualified service person- The pages that follow contain the required maintenance nel, special tools, and equipment to perform all service services determined by the engineers who designed your operations in an expert manner.
Page 384: Engine Oil
MAINTAINING YOUR VEHICLE 383 Engine Oil CAUTION! (Continued) Checking Oil Level • Your vehicle has been built with improved fluids To assure proper engine lubrication, the engine oil must that protect the performance and durability of be maintained at the correct level. Check the oil level at your vehicle and also allow extended maintenance regular intervals, such as every fuel stop.
Page 385 384 MAINTAINING YOUR VEHICLE when the reading is at the low end of the indicated range Engine Oil Selection will result in the oil level at the full end of the indicator For best performance and maximum protection for all range.
Page 386 MAINTAINING YOUR VEHICLE 385 Synthetic Engine Oils CAUTION! You may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- Do not use chemical flushes in your engine oil as the mended maintenance intervals for oil and filter changes chemicals can damage your engine.
Page 387: Engine Oil Filter
386 MAINTAINING YOUR VEHICLE station, or governmental agency for advice on how and Engine Air Cleaner Filter where used oil and oil filters can be safely discarded in Refer to “Maintenance Schedule” for further information. your area. WARNING! Engine Oil Filter The engine oil filter should be replaced at every engine The air cleaner can provide a measure of protection oil change.
Page 388: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 387 Maintenance-Free Battery WARNING! (Continued) The top of the maintenance-free battery is permanently • Battery posts, terminals, and related accessories sealed. You will never have to add water, nor is periodic contain lead and lead compounds. Wash hands maintenance required.
Page 389: Air Conditioner Maintenance
388 MAINTAINING YOUR VEHICLE CAUTION! (Continued) CAUTION! • If a “fast charger” is used while the battery is in Do not use chemical flushes in your air conditioning the vehicle, disconnect both vehicle battery cables system as the chemicals can damage your air condi- before connecting the charger to the battery.
Page 390: Body Lubrication
MAINTAINING YOUR VEHICLE 389 Body Lubrication WARNING! (Continued) Locks and all body pivot points, including such items as • The air conditioning system contains refrigerant seat tracks, door hinge pivot points and rollers, liftgate, under high pressure. To avoid risk of personal tailgate, sliding doors and hood hinges, should be lubri- injury or damage to the system, adding refrigerant cated periodically with a lithium based grease, such as...
Page 391: Windshield Wiper Blades
390 MAINTAINING YOUR VEHICLE amount of a high quality lubricant, such as MOPAR NOTE: Life expectancy of wiper blades varies depend- Lock Cylinder Lubricant or equivalent directly into the ing on geographical area and frequency of use. Poor lock cylinder. performance of blades may be present with chattering, marks, water lines or wet spots.
Page 392: Exhaust System
MAINTAINING YOUR VEHICLE 391 Exhaust System WARNING! The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust Exhaust gases can injure or kill. They contain carbon system. monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can If you notice a change in the sound of the exhaust system, eventually poison you.
Page 393 392 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- WARNING! verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure A hot exhaust system can start a fire if you park over proper catalyst operation and prevent possible catalyst materials that can burn.
Page 394: Cooling System
MAINTAINING YOUR VEHICLE 393 To minimize the possibility of catalyst damage: WARNING! (Continued) • Do not shut off the engine or interrupt the ignition • You or others can be badly burned by hot coolant when the transaxle is in gear and the vehicle is in or steam from your radiator.
Page 395 394 MAINTAINING YOUR VEHICLE Check the coolant recovery bottle tubing for brittle rub- CAUTION! ber, cracking, tears, cuts and tightness of the connection • Mixing of engine coolant (antifreeze) other than at the bottle and radiator. Inspect the entire system for leaks.
Page 396 MAINTAINING YOUR VEHICLE 395 When adding engine coolant (antifreeze), a minimum CAUTION! (Continued) solution of 50% recommended MOPAR Antifreeze/ • This vehicle has not been designed for use with Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Propylene Glycol based engine coolant (anti- Organic Additive Technology), or equivalent, in water freeze).
Page 397 396 MAINTAINING YOUR VEHICLE NOTE: Mixing engine coolant (antifreeze) types will WARNING! decrease the life of the engine coolant (antifreeze) and • The warning words “DO NOT OPEN HOT” on will require more frequent coolant changes. the cooling system pressure cap are a safety pre- Cooling System Pressure Cap caution.
Page 398 MAINTAINING YOUR VEHICLE 397 rules for your community. To prevent ingestion by ani- long as the engine operating temperature is satisfactory, mals or children do not store ethylene glycol-based the coolant bottle need only be checked once a month. engine coolant (antifreeze) in open containers or allow it When additional engine coolant (antifreeze) is needed to to remain in puddles on the ground.
Page 399: Brake System
398 MAINTAINING YOUR VEHICLE • Check the coolant freeze point in the radiator and in • Do not change the thermostat for Summer or Winter the coolant recovery bottle. If engine coolant (anti- operation. If replacement is ever necessary, install freeze) needs to be added, the contents of the coolant ONLY the correct type thermostat.
Page 400 MAINTAINING YOUR VEHICLE 399 Brake Master Cylinder fluid reservoir is low and the brake system does not The fluid level in the master cylinder should be checked indicate any leaks or other problems, it may be a result of when performing under hood services, or immediately if a leak in the hydraulic clutch release system.
Page 401: Automatic Transaxle (Cvt) - If Equipped
400 MAINTAINING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Do not allow petroleum based fluid to contami- moisture, use only new brake fluid or fluid that nate the brake fluid. Brake seal components could has been in a tightly closed container.
Page 402: Manual Transaxle - If Equipped
MAINTAINING YOUR VEHICLE 401 fluid which has been formulated with special metal to Special Additives metal friction coefficient additives to provide the proper Do not add any materials (other than leak detection dyes) steel belt traction on the drive and driven pulleys. Refer to Continuously Variable Transaxle (CVT) Fluid to “Fluids, Lubricants, and Genuine Parts”...
Page 403: Rear Drive Assembly (Rda) - Awd/4Wd Models Only
402 MAINTAINING YOUR VEHICLE Fluid Level Check Rear Drive Assembly (RDA) – AWD/4WD Models Check the fluid level by removing the fill plug. The fluid Only level should be between the bottom of the fill hole and a Lubricant Selection point not more than 3/16 in (4.7 mm) below the bottom Use only the manufacturer’s recommended fluid.
Page 404: Power Transfer Unit (Ptu) - Awd/4Wd Models Only
MAINTAINING YOUR VEHICLE 403 Power Transfer Unit (PTU) – AWD/4WD Models Appearance Care and Protection from Corrosion Only Protection of Body and Paint from Corrosion Lubricant Selection Vehicle body care requirements vary according to geo- Use only the manufacturer’s recommended fluid. Refer graphic locations and usage.
Page 405 404 MAINTAINING YOUR VEHICLE • Use a high quality cleaner wax, such as MOPAR The most common causes of corrosion are: Cleaner Wax to remove road film, stains and to protect • Road salt, dirt and moisture accumulation. your paint finish. Take care never to scratch the paint. •...
Page 406 MAINTAINING YOUR VEHICLE 405 • It is important that the drain holes in the lower edges • Use MOPAR Touch Up Paint or equivalent on of the doors, rocker panels and trunk be kept clear and scratches as soon as possible. Your authorized dealer open.
Page 407 406 MAINTAINING YOUR VEHICLE Stain Repel Fabric Cleaning Procedure – Interior Care If Equipped Use MOPAR Total Clean or equivalent to clean fabric Stain Repel seats may be cleaned in the following man- upholstery and carpeting. ner: Use MOPAR Total Clean or equivalent to clean vinyl •...
Page 408 MAINTAINING YOUR VEHICLE 407 Glass Surfaces WARNING! All glass surfaces should be cleaned on a regular basis with MOPAR Glass Cleaner or any commercial Do not use volatile solvents for cleaning purposes. household-type glass cleaner. Never use an abrasive type Many are potentially flammable, and if used in cleaner.
Page 409: Fuses
408 MAINTAINING YOUR VEHICLE Instrument Panel Bezels Seat Belt Maintenance Do not bleach, dye or clean the seat belts with chemical CAUTION! solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. When installing hanging air fresheners in your ve- If the seat belts need cleaning, use a mild soap solution or hicle, read the installation instructions carefully.
Page 410 MAINTAINING YOUR VEHICLE 409 inside of the cover. Refer to “Engine Compartment” in Cavity Cartridge Mini- Description “Maintaining Your Vehicle” for further information. Fuse Fuse Cavity Cartridge Mini- Description 30 Amp IOD Sense2 Fuse Fuse Green Empty Empty 40 Amp Power Seats Green 15 Amp...
Page 411 410 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini- Description Cavity Cartridge Mini- Description Fuse Fuse Fuse Fuse 15 Amp IGN Run/Acc Dome 15 Amp ENG ASD Relay Lt Blue Lamp/Sunroof/Rear Lt Blue Feed 3 Wiper Motor/ACC 15 Amp Power Sunroof Feed Inverter Lt Blue 10 Amp...
Page 412: Vehicle Storage
MAINTAINING YOUR VEHICLE 411 Cavity Cartridge Mini- Description CAUTION! Fuse Fuse • When installing the IPM cover, it is important to 10 Amp Headlamp Washer ensure the cover is properly positioned and fully Relay Control – latched. Failure to do so may allow water to get If Equipped into the IPM, and possibly result in an electrical 30 Amp...
Page 413: Replacement Bulbs
412 MAINTAINING YOUR VEHICLE • Disengage the mini-fuse in the Power Distribution LIGHTS BULBS – Exterior Bulb No. Center labeled IOD (Ignition Off-Draw). Low Beam/High Beam Headlamp ... . H13 Front Park/Turn Signal/Side Marker Lamp .
Page 414: Bulb Replacement
MAINTAINING YOUR VEHICLE 413 BULB REPLACEMENT 2. Reach into the engine compartment and pull the red lock out at the green connector. Headlamps 1. Raise the hood and locate the connector behind the headlamp.
Page 415 414 MAINTAINING YOUR VEHICLE 3. Remove green connector from back of bulb by pulling 4. Twist the bulb to the left. straight back.
Page 416: Fog Lamps
MAINTAINING YOUR VEHICLE 415 5. Pull bulb outward from assembly. NOTE: These are halogen bulbs. Take care not to touch the bulb with your fingers. Body oils from your fingers could cause excessive heat buildup which reduces bulb life. Fog Lamps 1.
Page 417: Tail Lamp, Rear Turn Signal And Backup Lamp
416 MAINTAINING YOUR VEHICLE Tail Lamp, Rear Turn Signal and Backup Lamp 2. Grasp the taillamp and pull firmly to disengage the lamp from the aperture panel. 1. Remove the two push-pins from the taillamp housing. 3. Twist and remove socket from lamp.
Page 418: License Lamps
MAINTAINING YOUR VEHICLE 417 4. Remove bulb from socket and replace. License Lamps 1. Use a screw driver to gently pry against the side of the snap tab to remove the lamp from the liftgate.
Page 419 418 MAINTAINING YOUR VEHICLE 2. Rotate the socket 1/4 turn counterclockwise. 3. Pull bulb from socket.
Page 420: Center High-Mounted Stoplamp
MAINTAINING YOUR VEHICLE 419 Center High-Mounted Stoplamp Light is an LED assembly. See your authorized dealer for replacement. Off-Road Lamp 1. Remove the three screws attaching the lens to the housing.
Page 421 420 MAINTAINING YOUR VEHICLE 2. Unlatch the wire clasp securing the bulb into the 3. Disconnect the bulb from the lamp harness to replace housing and rotate it into the position shown. the bulb.
Page 422: Fluid Capacities
MAINTAINING YOUR VEHICLE 421 FLUID CAPACITIES U.S. Metric Fuel (Approximate) 13.6 Gallons 51.5 Liters Engine Oil with Filter 2.0L and 2.4L Engine (SAE 5W-20, API Certified) 4.5 Quarts 4.26 Liters Cooling System * 2.0L and 2.4L Engine (MOPAR Engine Coolant/Antifreeze 5 7.2 Quarts 6.8 Liters Year/100,000 Mile Formula or equivalent)
Page 423: Fluids, Lubricants, And Genuine Parts
422 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hy- brid Organic Additive Technology) or equivalent. Engine Oil Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
Page 424: Chassis
MAINTAINING YOUR VEHICLE 423 Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transaxle (CVT) – If MOPAR CVTF+4 Equipped Manual Transaxle – If Equipped MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed ATF+4 product. Rear Drive Assembly (RDA) MOPAR Gear & Axle Lubricant SAE 80W-90 API GL 5 or equivalent non-synthetic product.
Page 426 MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..426 Maintenance Schedule ....426 Required Maintenance Intervals ..428...
Page 427 426 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULE The Scheduled Maintenance services listed in bold type The oil change indicator system will remind you that it is must be done at the times or mileages specified to ensure time to take your vehicle in for scheduled maintenance. the continued proper functioning of the emissions control On Electronic Vehicle Information Center (EVIC) system.
Page 428 MAINTENANCE SCHEDULES 427 NOTE: referring to the steps described under “Electronic Vehicle • The oil change indicator message will not monitor the Information Center/Engine Change Indicator time since the last oil change. Change your vehicle’s System/Oil Change Required” in “Understanding Your oil if it has been six months since your last oil change Instrument Panel”...
Page 429 428 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check the tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the brake hoses and lines. • Inspect the battery and clean and tighten the terminals •...
Page 430 MAINTENANCE SCHEDULES 429 6,000 Miles (10,000 km) or 12,000 Miles (20,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 431: Service Schedule
430 MAINTENANCE SCHEDULES 18,000 Miles (30,000 km) or 24,000 Miles (40,000 km) or 24 Months Maintenance Service 18 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 432 MAINTENANCE SCHEDULES 431 30,000 Miles (50,000 km) or 36,000 Miles (60,000 km) or 36 Months Maintenance Service 30 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 433 432 MAINTENANCE SCHEDULES 42,000 Miles (70,000 km) or 48,000 Miles (80,000 km) or 48 Months Maintenance Service 42 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 434 MAINTENANCE SCHEDULES 433 54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer...
Page 435 434 MAINTENANCE SCHEDULES 60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs. ❏ Inspect the brake linings; replace if necessary. ❏...
Page 436 MAINTENANCE SCHEDULES 435 66,000 Miles (110,000 km) or 72,000 Miles (120,000 km) or 72 Months Maintenance Service 66 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 437 436 MAINTENANCE SCHEDULES 78,000 Miles (130,000 km) or 84,000 Miles (140,000 km) or 84 Months Maintenance Service 78 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 438 MAINTENANCE SCHEDULES 437 90,000 Miles (150,000 km) or 96,000 Miles (160,000 km) or 96 Months Maintenance Service 90 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 439 438 MAINTENANCE SCHEDULES 102,000 Miles (170,000 km) or 108,000 Miles (180,000 km) or 108 Months Maintenance Service 102 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 440 MAINTENANCE SCHEDULES 439 114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. Odometer Reading Date Repair Order # Dealer Code Signature Authorized Chrysler Dealer...
Page 441 440 MAINTENANCE SCHEDULES 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs. ❏ Inspect the brake linings; replace if necessary. ❏...
Page 442 MAINTENANCE SCHEDULES 441 126,000 Miles (210,000 km) or 132,000 Miles (220,000 km) or 132 Months Maintenance Service 126 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 443 442 MAINTENANCE SCHEDULES 138,000 Miles (230,000 km) or 144,000 Miles (240,000 km) or 144 Months Maintenance Service 138 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate tires. ❏ Change the engine oil and engine oil ❏...
Page 444 MAINTENANCE SCHEDULES 443 150,000 Miles (250,000 km) or 150 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Replace the spark plugs. ❏ Adjust the parking brake on vehicles equipped with four-wheel disc brakes.
Page 445 444 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer to the owner, but is not required to maintain emissions warranty. WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment.
Page 446: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Customer Assistance For The Hearing Or Vehicle......447 Speech Impaired (TDD/TTY) .
Page 447 446 IF YOU NEED CONSUMER ASSISTANCE Department Of Transportation Uniform Tire Traction Grades ..... 453 Quality Grades ......453 Temperature Grades .
Page 448: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 447 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
Page 449: Chrysler Group Llc Customer Center
448 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 solved with this process. Auburn Hills, MI 48321–8004 Phone: (800) 992-1997 •...
Page 450: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 449 Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
Page 451: Warranty Information (U.s. Vehicles Only)
450 IF YOU NEED CONSUMER ASSISTANCE has also made a major investment in facilities, tools, and WARRANTY INFORMATION (U.S. Vehicles Only) training to assure that you are absolutely delighted with See the Warranty Information Booklet, located on the the ownership experience. You’ll be pleased with their DVD, for the terms and provisions of Chrysler Group sincere efforts to resolve any warranty issues or related LLC warranties applicable to this vehicle.
Page 452: In Canada
IF YOU NEED CONSUMER ASSISTANCE 451 If NHTSA receives similar complaints, it may open an Transport Canada, Motor Vehicle Defect Investigations investigation, and if it finds that a safety defect exists in and Recalls, 2780 Sheffield Road, Ottawa, Ontario K1B a group of vehicles, it may order a recall and remedy 3V9.
Page 453 452 IF YOU NEED CONSUMER ASSISTANCE • Owner’s Manuals vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, These Owner’s Manuals have been prepared with the and charts. assistance of service and engineering specialists to • Diagnostic Procedure Manuals acquaint you with specific Chrysler Group LLC ve- hicles.
Page 454 IF YOU NEED CONSUMER ASSISTANCE 453 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration.
Page 455 454 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 456 INDEX...
Page 457 456 INDEX ABS (Anti-Lock Brake System) ....297 Airbag, Window (Side Curtain) ... 60,63,66 Adding Engine Coolant (Antifreeze) ..395 Alarm Light .
Page 458 INDEX 457 Overheating ......360 Brakes ......296,398 Selection Of Lubricant .
Page 459 458 INDEX Cargo Light ......169 Cleaning Cargo Load Floor ......172 Wheels .
Page 460 INDEX 459 Disposal of Used Coolant ....396 Disposal Drain, Flush, and Refill ....394 Antifreeze (Engine Coolant) .
Page 461 460 INDEX Electronic Stability Program ....303 Oil Change Interval ....384 Traction Control System .
Page 462 INDEX 461 Flat Tire Stowage ......365 Additives ......337 Flooded Engine Starting .
Page 463 462 INDEX Gauges Headlights ......413 Coolant Temperature ....189 Cleaning .
Page 464 INDEX 463 Ignition Key Removal ..... 12 Key, Programming ......17 Immobilizer (Sentry Key) .
Page 465 464 INDEX Lights ......83,140 License ......417 Airbag .
Page 466 INDEX 465 Locks Map/Reading Lights ..... 144 Child Protection ......32 Master Cylinder (Brakes) .
Page 467 466 INDEX Odometer ......192 Overheating, Engine ....189,358 Trip .
Page 468 INDEX 467 Windows ......33 Recreational Towing ..... . 355 Power Steering Fluid .
Page 469 468 INDEX Roll Over Warning ......4 Child Restraint ......72 Roof Rack (Luggage Rack) .
Page 470 INDEX 469 Service Assistance ..... . . 447 Starting ....... 277 Service Contract .
Page 471 470 INDEX System, Remote Starting ....25 Changing ......360 Compact Spare .
Page 472 INDEX 471 Spinning ......321 Transaxle ......282 Tread Wear Indicators .
Page 473 472 INDEX Uniform Tire Quality Grades ....453 Warranty Information ..... 450 Universal Consumer Interface (UCI) Connector .
Page 474 Chrysler Group LLC 10MK49-126-AB Printed in U.S.A. 2nd Edition...

This manual is also suitable for:

Compass 2019 2010 compass

Jeep Compass Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

Chapters

Related Manuals for Jeep Compass

Summary of Contents for Jeep Compass