Craftsman 315.115160 Operator's Manual page 6

5-1/2 in, 19.2 volt cordless laser trim saw
Hide thumbs Also See for 315.115160:
Table of Contents

Advertisement

_l
WARNING!READ ANDUNDERSTAND ALL
iNSTRUCTiONS° Failure to followallinstructions
listedbelow, m ayresult i nelectricshock, f ire
and/orserious personal injury.
[] Beforeusingbatterycharger,readal!instructions
andcautionary m arkings
i n this manual, on battery
charger, battery, and product using battery to prevent
misuse of the products and possible injury or damage.
CAUTION: To reduce the risk of electric shock or
damage to the charger and battery, charge only
nickel=cadmium rechargeable batteries as specifi=
cally designated on your charger. Other types of
batteries may burst, causing personal injury or
damage.
[] Do not use charger outdoors
or expose to wet or
damp conditions.
Water entering charger will increase
the risk of electric shock.
[] Use of an attachment
not recommended
or sold
by the battery charger
manufacturer
may result in
a risk of fire, electric
shock, or injury to persons.
Following this rule will reduce the risk of electdc shock,
fire, or serious personal injury.
[] Do not abuse cord or charger.
Never use the cord to
carry the charger. Do not pull the charger cord rather
than the plug when disconnecting
from receptacle.
Damage to the cord or charger could occur and create
an electric shock hazard. Replace damaged cords ira=
mediately.
[] Make sure cord is located so that it will not be
stepped
on, tripped
over, come in contact
with
sharp edges or moving parts or otherwise
subject-
ed to damage
or stress. This wil! reduce the risk of
accidental fails, which could cause injury, and damage
to the cord, which could result in electric shock.
[] Keep cord and charger
from heat to prevent
damage to housing
or internal
parts.
[] Do not let gasoline, oils, petroleum=based
products,
etc. come in contact
with plastic
parts. They contain
chemicals that can damage, weaken, or destroy plastic.
[] An extension
cord should not be used unless
absolutely
necessary.
Use of improper extension cord
could result in a risk of fire and electric shock. If
extension cord must be used, make sure:
a. That pins on plug of extension cord are the
same number, size and shape as those of
plug on charger.
b. That extension cord is properly wired and in
good electrical condition; and
c. That wire size is large enough for AC ampere
rating of charger as specified below:
Cord Length (Feet)
25'
50'
100'
Cord Size (AWG)
16
16
16
NOTE: AWG = American Wire Gauge
[] Do not operate
charger with a damaged
cord or
plug, which could cause shorting and electric shock. If
damaged, have the charger replaced by an authorized
serviceman.
[] Do not operate
charger
if it has received a sharp
blow, been dropped,
or otherwise
damaged
in any
way. Take it to an authorized serviceman for electrical
check to determine if the charger is in good working
order.
[] Do not disassemble
charger.
Take it to an authorized
serviceman when service or repair is required. Incor-
rect reassembly may result in a risk of electric shock or
fire.
[] Unplug charger
from outlet before attempting
any
maintenance
or cleaning to reduce the risk of
electric
shock.
[] Disconnect
charger
from the power supply when
not in use. This wi[! reduce the risk of electric shock
or damage to the charger if metal items should fail into
the opening. It also wi[! help prevent damage to the
charger during a power surge.
[] Risk of electric
shock.
Do not touch uninsulated
portion of output connector or uninsulated battery
terminal.
[] Save these instructions.
Refer to them frequently and
use them to instruct others who may use this too!. If
you loan someone this tool, loan them these instruc-
tions also to prevent misuse of the product and
possible injury.
_
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction
activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
lead from lead-based paints,
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic
particles.
6

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents