Table of Contents
Advertisement
Quick Links
FOR THE WAY YOU LIVE
Congratulations! You are the owner of the 2-
the advantages of your appliance, please take a few minutes to read all the "Use &
Care Instructions" and keep the instructions handy for easy reference. Please review
the product warranty and mail the owner registration form.
EURO-PRO Operating LLC: 21 Lawrence Paquette Industrial Drive, Champlain, New York 12919
USE AND CARE INSTRUCTIONS
4400 Bois Franc, St. Laurent, Quebec H4S 1A7
Tel.: 1 (800) 798-7398
2-
-1 Cordless/Corded Iron
IN
-1 Cordless/Corded Iron. To fully enjoy
IN
Model EP485
Advertisement
Table of Contents
Related Manuals for Euro-Pro EP485
Summary of Contents for Euro-Pro EP485
- Page 1 Care Instructions” and keep the instructions handy for easy reference. Please review the product warranty and mail the owner registration form. EURO-PRO Operating LLC: 21 Lawrence Paquette Industrial Drive, Champlain, New York 12919 4400 Bois Franc, St. Laurent, Quebec H4S 1A7 Tel.: 1 (800) 798-7398...
-
Page 2: Important Safeguards
10. Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electrical shock, do not disassemble the iron. Send it to an authorized EURO-PRO Operating LLC service center for examination and repair. Incorrect reassembly can cause a risk of electric shock when iron is used. -
Page 3: Polarized Plug
1. To avoid a circuit overload, do not operate another high-wattage appliance on the same circuit. 2. If an extension is absolutely necessary, a 15-ampere rated cord with a polarized plug should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled on or tripped over. - Page 4 -1 CORDLESS/CORDED IRON 1. Temperature Control Dial 2. Variable Steam Control 3. Spray Button 4. Spray Nozzle 5. Burst of Steam Button 6. Water Filling Inlet Cover 7. Thermostat Light 8. Water Level Window 9. Stainless Steel Sole Plate 10. Soft Hand Grip 11.
-
Page 5: Before First Use
Remove any labels, stickers or tags which may be attached to the body or soleplate of the iron before using the iron. Read all instructions for use carefully. Always follow the Important Safeguards. The first time an iron is used, some odor and small white particles may come out of the steam vents. - Page 6 • The red thermostat light (7) will come on indicating that the iron is heating up. • When the red light goes out, the set temperature has been reached and the iron is ready to use. • The thermostat light (7) will go on & off as the thermostat is switching the heating element...
- Page 7 (high temperature) Please note: Before starting to iron delicate fabrics, it is best to first test the temperature of the iron on a hem or an inside seam. TO SELECT IRON TEMPERATURE, LINE UP TEMPERATURE SELECTED ON DIAL WITH THE RED TRIANGLE ON THE WATER TANK.
-
Page 8: Filling With Water
(see fig. 1) • Place the iron horizontally and open the Water Filling Inlet Cover (6). Pour water into the water filling inlet (6) to a maximum of approximately 8 oz. (230ml). Use the water bottle with the spout for this purpose. -
Page 9: Ironing With Steam
• Steam is produced as soon as the iron is held in a horizontal position. • Steam will stop coming out when the iron is put on its heel in a vertical position or by turning the steam control dial to ‘0’. -
Page 10: Setting The Temperature
• Place the iron on the stand. (Fig. 3) • Insert the plug into the wall outlet. • Set the appropriate ironing temperature indicated in the ironing instructions or in the fabric table by means of the temperature dial (1). (Fig. 4) •... - Page 11 • Set the 3-position switch (13) to position 13C. (Fig. 6) • Take the iron with the power unit ( 11) from the stand. (Fig. 7) • Either place iron on heel rest or on the stand (12) when you interrupt ironing. Fig. 6 •...
-
Page 12: Water Spray
• Ensure that there is enough water in the water reservoir. • Place the iron on its stand (12) and set the temperature control dial (1) to the required position within the “steam area” (•• for moderate or ••• for maximum steam). - Page 13 • Unplug the iron from the power source. • Set variable steam control to ‘MAX’. • Open the water inlet cover and turn the iron up-side down over the sink with the tip pointing downward and allow the water to flow from the opening.
-
Page 14: Self-Cleaning
• Open the water filling inlet cover (6) and fill the water reservoir up to the Max indication. • Close the water filling inlet cover (6) and place the iron on its stand (12). Plug unit into wall outlet and wait until the iron heats up and the thermostat light (7) goes off and then comes on again. - Page 15 ATTACHING IRON TO THE IRONING BOARD Your iron is equipped with a clamp that can be used to attach the iron stand (12) to your ironing board (or any other suitable surface). (Fig. 14.) Rotate the clamp 90°, so that it points down.
- Page 16 • If you use spray starch, wipe the soleplate occasionally with a soft damp cloth to prevent the forming of a deposit. • If the iron has not been used for a few weeks, hold the iron horizontally and allow it to steam for 2 minutes before ironing.
- Page 17 • Overuse of steam burst. Allow more time between each burst. • Iron may have been overfilled. Turn iron off,empty water and follow instructions for filling. • Steam performance may be low if iron requires seasoning. Use regular tap water for 1or 2 tanks until steam performance improves...
-
Page 18: Important Service Information
Champlain, N. Y. 12919 If the warranty period has expired, please send your iron postage pre-paid to the Service Dept. of EURO-PRO Operating LLC at the above address. You will be advised of the cost of repair before any servicing is done unless you enclose a note indicating that you would like us to proceed with the repairs and return the iron to you C.O.D. - Page 19 EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of purchase. The liability of EURO-PRO Operating LLC is limited solely to the repair or replacement of the product at EURO-PRO’s option. This warranty does not cover damage caused by misuse, negligence, use on improper current or voltage, use contrary to operating instructions or disassembly, repair or alteration by any person other than an authorized EURO-PRO Operating LLC service station.
Need help?
Do you have a question about the EP485 and is the answer not in the manual?
Questions and answers