Table of Contents
Advertisement
Quick Links
Tank Water Capacity Approx.: 1 Liter
Congratulations! You are the owner of the Steam Station. To fully enjoy the
advantages of your appliance, please take a few minutes to read all the "Use &
Care Instructions" and keep the instructions handy for easy reference. Please
review the product warranty and mail the owner registration form.
EURO-PRO OPERATING LLC, 21 Lawrence Paquette Industrial Drive, Champlain, New York 12919
Steam Station
Model EP7005
120 Volt, 60 Hz, 1400 W.
Use and Care Instructions
4400 Bois Franc, St. Laurent, Quebec. H4S 1A7
Tel: (800) 798-7395
Advertisement
Table of Contents
Related Manuals for Euro-Pro STEAM STATION EP7005
Summary of Contents for Euro-Pro STEAM STATION EP7005
- Page 1 Care Instructions” and keep the instructions handy for easy reference. Please review the product warranty and mail the owner registration form. EURO-PRO OPERATING LLC, 21 Lawrence Paquette Industrial Drive, Champlain, New York 12919 4400 Bois Franc, St. Laurent, Quebec. H4S 1A7...
-
Page 2: Important Safeguards
6. Always disconnect iron from electrical outlet when filling iron with water or emptying and when not in use. 7. Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electrical shock, do not disassemble the iron. -
Page 3: Special Instructions
(8A) to the iron (14) before steam will exit: water requires approximately 2 minutes to pass through the hose (12) and reach the iron (14). Once this is done, you will not have to wait again - you will have continuous steam (if you keep pump on). -
Page 4: Main Components
Steam Trigger (Pull) 3A. Steam Trigger Lock Spray Button (Push) Spray Nozzle Burst-of-steam (Push) Temperature Pilot Light (right side) Iron Stand 8A. Water Tank 8B. Water Tank Lock Water Filling Hole 10. Rubber Mat 11. Power Cord 12. Connecting Cord / Supply Hose 13. - Page 5 Try out the ironing temperature which is most suitable there. (Start at a relatively low temperature.) Pure woolen fabrics (100% wool) may be pressed with the iron set to a steam position. Preferable set the steam control to maximum position and use a dry pressing cloth.
-
Page 6: Before First Use
How the Water is Pumped to the Iron 1. The water is pumped from the water tank (8A) to the iron (14) through the supply hose (12) by a built-in water pump. 2. This water pump is activated by pulling on the trigger (3). The water pump pilot light (15) will go on. - Page 7 • The iron stand (8) has 5 holes on the circumference of its top. • The rubber mat (10) has 5 pins in the corresponding locations. • Place the rubber mat (10) on top of the iron stand (8) and push each individual pin into its hole. (Fig. 1) IMPORTANT: Never place the hot iron on the plastic iron stand without the rubber mat on top of the iron stand.
-
Page 8: Filling The Water Tank
Starch, conditioner, perfume and fabric conditioner should never be added to the water. These result in residues in the steam chamber which will damage your iron and stain your laundry. For this reason, no condensed water (water from driers may be used, as this can contain additives (e.g. -
Page 9: Ironing Without Steam
How the Water is Pumped to the Iron 1. The water is pumped from the water tank (8A) to the iron (14) through the supply hose (12) by a built-in water pump. 2. This water pump is activated by pulling on the trigger (3). The water pump pilot light (15) will go on. -
Page 10: Ironing With Steam
• Set the variable steam control (2) TO “0”. (Fig. 3) • Fill the water tank (8A) with tap water, following the instructions for filling the water tank. • Make sure that the iron is resting on top of the rubber mat (10). IMPORTANT: Do not place the rubber mat (10) on a table or any other surface which may be damaged by heat. -
Page 11: Anti-Drip Function
The anti-drip shut-off functions as follows: At low temperature, the iron will stop steaming. To avoid the formation of water droplets, when the drip-stop is activated, you will hear a “click” indicating the flow of water has been stopped. Set the temperature control (1) up to the correct setting, steam will recommence as soon as the appropriate temperature has been reached. - Page 12 Burst-Of-Steam Function • By pushing the “Burst-of-Steam” button (6) a powerful shot of steam is emitted from the soleplate. (Fig. 6) • This steam is useful, for example, when removing stubborn creases and can be used during continuous steaming, but do not use burst of steam too often in a short period or you will get water spots..
- Page 13 Steaming in a Vertical Position • Burst-of-Steam (6) can also be applied when holding the iron in a vertical position. (Fig. 7) this is useful when removing creases from hanging clothes, curtains, etc… The Burst-of- Steam (6) feature can only be used while ironing at high temperatures at an interval of 5 seconds.
- Page 14 Attaching Iron to the Ironing Board Your Steam Station is equipped with a clamp that can be used to attach the iron stand (8) to your ironing board (or any other suitable surface). (Fig. 10) • Rotate the clamp 90°, so that it points down.
- Page 15 • Pour any remaining water out of the water tank (8A). • Set the steam control (2) to position “0” (= no steam). • Put the iron on the rubber mat (10) on its stand (8) and let cool down sufficiently before you store it.
- Page 16 • Iro n m a y h ave b een o ve rfille d . T u rn iron off, em pty w a te r a nd ven ts fo llo w in stru ctio n s for fillin g.
-
Page 17: One (1) Year Limited Warranty
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes.