Craftsman 917.28033 Operator's Manual page 27

DOR
a sin el captador
lsitivos de segu-
,s condiciones.
)r superior de la
(2) situada en la
nsacadora (deje
r los extremos),,
ficios del lade
Jperior soldada
)s orificios cor_
astidor superior
aredondade 1/4
)rcas de 1/4 (6).,
izq - uierdo de la
e la ensacadora
dientes de! tubo
_nsacadora (1).,
aredondade 1/4
.=rcasde 1/4 (6)°
.'abeza redonda
_n los lados del
adora, y apriete
TO REMOVE WHEEL FOR REPAIRS
1. Block up axle securely.
2. Remove axle cover, retaining ring and
washers to allow wheel removal (rear
wheels have a square key - Do not lose).
3o Repair tire and reassemble.
NOTE: On rear wheels only: align grooves in
rear wheel hub and axle. insert square key.
4. Replace washers and snap retaining ring
securely in axle groove.
5_ Replace axle cover,.
NOTE: To seal tire punctures and prevent
flat tires due to slow leaks, purchase and
use tire sealant from Sears° Tire sealant also
prevents tire dry rot and corrosion.
Washers
Retaining
Axle Ring,
Square
Key _
(Rear W, iheel Only) _-
FRONT WHEEL TOE - IN/CAMBER
"four new tractor front wheel toe - in and
camber is set at the factory and is normal. The
frontwheel toe -in and camber are not adjust-
ableo If damage has occurred to affect the
factory set front wheeltoe -in or camber, con-
tact a Sears or other qualified service center.
TO START ENGIN EWITH WEAK BATTERY
_,WARNING: Lead-acid batteries generate
explosive gases. Keep sparks, flame and
smokingmaterialsawayfrom batteries.Always
wear eye protection when around batteries.
If your battery istoo weakto startthe engine, it
should be recharged. (See "BATTERY" in the
MAINTENANCE section of this manual).
If "jumper cables" are used for emergency
starting, follow this procedure:
IMPORTANT: Your tractor is equipped with a
12 volt system. The other vehicle must also
be a 12 volt system.. Do not use your tractor
Weak or _ Fully
Dead [[_] E_]l !_1 Charged
Battery BaLtery
3. Connect the other end of the BLACK
cable (D) to good chassis ground, away
from fuel tank and battery.
TO REMOVE CABLES, REVERSE ORDER -
1. BLACK cable first from chassis and then
from the fully charged battery.
2. RED cable last from both batteries_
REPLACING BATTERY
n_asWARNING: _Do not short battery termi-
by allowing awrench or any other object
to contact both terminals at the same time.
Before connecting battery, remove metal
bracelets, wrist*watch bands, rings, etc.
Positive terminal must be connected first to
prevent sparking from accidental grounding.
1o Lift seat pan to raised position.
2o Disconnect BLACK battery cable first
then RED battery cable and carefully
remove battery from tractor.
3. Install new battery with terminals in same
position as old battery°
4. First connect RED battery cable to posi-
tive (+) terminal with hex bolt and keps
nut as shown. Tighten securely, Slide
terminal cover over terminal
5. Connect BLACK grounding cable to
negative (-) terminal with remaining hex
bolt and keps nut. Tighten securely_
Seat
battery to start other vehicles. Terminal Nut
Cover Negative Bolt
TO ATTACH JUMPER CABLES - ' ............... ,- ..... "................ /
b _lacK)
1. Connect one end of the RED ca le _..._ _Cable... ".(_.
to the POSITIVE (+) terminal of each ' _ _ --_
battery(A- B), taking care not to short Positiv
against tractor chassis. (Red)
2o Connect one end of the BLACK cable Cable
to the NEGATIVE (-) terminal (C) of fully
charged battery.
27