Model No. 919.167710 Running HP "1.6 Bore 2.875" Stroke 1.45" Voltage-Single Phase 120V/60HZ Minimum Branch Circuit Requirement 15 amps Fuse Type Time Delay Air Tank Capacity (gallons) 26 (98.4 liters) Approx. Cutqn 130 psi Approx. Cut-out 160 psi SCFM @ 40 psig *6.3 SCFM @ 90 psig *4.9...
Page 4
RISK OF EXPLOSION OR FiRE WHAT CAN HAPPEN HOW TO PREVENT iT It is normal for electrical contacts Always operate the compressor within the motor and pressure in a well ventilated area free of switch to spark, combustible materials, gasoline, or solvent vapors.
Exposure to chemicals in dust cre- • Work in an area with good cross ventilation. Read and follow the ated by power sanding, sawing, grinding, drilling, and other con- safety instructions provided on the struction activities may be harmful. label or safety data sheets for the materials you are spraying.
Page 6
Tires: • Over inflation of tires could result in • Use a tire pressure gauge to check serious injury and property damage, the tires pressure before each use and while inflating tires; see the tire sidewall for the correct tire pressure. NOTE: Air tanks, compressors and similar equipment used to inflate tires can fill small tires similar to these very rapidly.
Page 7
RiSK FROM FLYING OBJECTS WHAT CAN HAPPEN HOW TO PREVENT IT The compressed air stream can Always wear certified safety cause soft tissue damage to equipment: ANSI Z87.1 eye exposed skin and can propel dirt, protection (CAN/CSA Z94.3) chips, loose particles, and small with side shields when using the objects at high speed, resulting in com pressor.
Page 8
RiSK OF UNSAFE OPERATION WHAT CAN HAPPEN HOW TO PREVENT iT Review and understand all Unsafe operation of your air • • compressor could lead to serious instructions and warnings in this manual. injury or death to you or others. •...
Page 9
RISK OF iNJURY FROM LiFTiNG WHAT CAN HAPPEN HOW TO PREVENT IT Serious injury can result from • The compressor is too heavy to attempting to lift too heavy an be lifted by one person. Obtain assistance from others before object.
This unit is capable of powering the following Accessories. The accessories are available through the current Power and Hand Tool Catalog or full-line Sears stores. Accessories Refer to the selection chart located on the unit to select the tools this unit is •...
Page 11
Attach wheels with shoulder bolts Assemble Rubber Strip and nuts as shown. Clean and dry underside of air Tighten securely. NOTE: The unit tank leg opposite wheels. will sit level if the wheels are prop- Remove the protective paper strip erly installed.
EXTENSION CORDS If any of the above conditions cannot If an extension cord must be used, be be met, or if operation of the com- sure it is: pressor repeatedly causes interruption of the power, it may be necessary to •...
Page 13
KNOW YOUR AIR COMPRESSOR READ THiS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. Tank Pressure Gauge: The tank pres- Description of Operation sure gauge indicates the reserve air...
enter the air tank. When the air Before Starting compressor reaches "cut-out" Do not operate this pressure, the check valve "closes", unit until you read allowing air pressure to remain inside and understand this instruction the air tank. manual for safety, operation Pressure maintenance instructions.
Page 15
Bow to Start Before Each Start=Up Place Auto/Off switch to "Off". Turn the Auto/Off switch to "On/Auto" and allow tank pres- Pull regulator knob out, turn sure to build. Motor will stop counter-clockwise until it stops. when tank pressure reaches "cut- Push knob in to lock in place.
Page 16
CUSTOMER RESPONSiBiLiTiES Procedure Daily Daily Weekly or after each use Check safety valve inspect air filter Drain air tank Check for unusual noise/vibration Check for air leaks* Clean compressor exterior To check for air leaks apply a solution of soapy water around joints. While compressor is pumping to pressure and after pressure cuts out, look for air bubbles to form.
Page 17
NOTE: All compressed air systems After the water has been drained, generate condensate that accumulates close the drain valve (clockwise). The air compressor can now be in any drain point (e.g., tanks, filter, after- stored. coolers, dryers). This condensate con- NOTE: If drain valve is plugged, tains lubricating oil and/or substances release all air pressure.
Page 18
Risk of unsafe operation. Unit Pressure Tube cycles automatically when power is Outlet Relief on. When doing Maintenance, you may be exposed to voltage sources, compressed air or moving parts. Check Personal injuries can occur. Valve Before servicing: • Unplug or disconnect electrical supply to the air compressor.
Page 19
Remove the gauges and quick Assemble the regulator. NOTE: Arrow indicates flow of air. Make connect from the regulator. sure it is pointing in the direction of air flow. Regulator ReguLato Connect Reapply pipe sealant to gauges Remove the regulator. and quick connect.
Page 20
Before you store the air compressor, Water will condense make sure you do the following: in the air tank. Review the Maintenance section not drained, water will corrode and on the preceding pages and per- weaken the air tank causing a risk form scheduled maintenance as of air tank rupture.
Risk of Unsafe Operation. Unit cycles automatically when power is on. When servicing, you may be exposed to voltage sources, compressed air, or moving parts. Before servicing unit unplug or disconnect electrical supply to the air compressor, bleed tank of pressure, and allow the air compressor to cool.
PROBLEM CAUSE CORRECTION Pressure read- It is normal for "some" If there is an excessive ing on the regu- 3ressure drop to occur. amount of pressure drop when lated pressure the accessory is used, adjust gauge drops the regulator following the when an acces- instructions in the Description sory is used.
Page 23
PROBLEM CAUSE CORRECTION Motor will not Extension cord is wrong Check for proper gauge wire run. length or gauge, and cord length. Check valve stuck open. Replace check valve. Loose electrical connections. Have checked by a Trained Service Technician. Possible defective motor. Have checked by a Trained Service Technician.
Page 24
GARANTIA ............CUADRO DE ESPECIFICACIONES ........DEFINICIONES DE NORMAS DE SEGURIDAD ......IMPORTANTES INSTRUCCIONES DE SEGURIDAD ....29-35 GLOSARIO ............ACCESORIOS ............ ClCLO DE SERVICIO ..........ENSAMBLADO ........... INSTALACION ..........37-38 OPERACION ........... 39-41 MANTENIMIENTO ..........42-43 SERVlClO Y AJUSTES ...........
Page 25
Modelo N ° 919.167710 HP de Trabajo "1,6 Diametro interior 2,875 pulg. (73,0 mm) Carrera 1,45 pulg. (35,6 mm) Tensi6n monofasica 120V/60HZ Circuito minimo requerido Acci6n retardada Tipo de fusible Capacidad de aire en el tanque 26 Galones (98,4 litros) Presi6n de corte de entrada 130 psi Presi6n de corte de salida...
Page 26
RIESGO DE EXPLOSION 0 INCENDIO &QUE PUEDE SUCEDER? COMO EVITARLO • Es normal que los contactos el6ctricos • Opere siempre el compresor en un dentro del motor y el interruptor de area bien ventilada libre de materiales presi6n produzcan chispas, combustibles, gasolina o vapores de solventes.
Page 27
La exposici6n a productos quimicos en Trabaje en un Area con buena el polvo producido por las herramientas ventilacidn cruzada. Lea y siga las el6ctricas al lijar, aserrar, esmerilar, instrucciones de seguridad que se proveen en la etiqueta o en la ficha taladrar y otras actividades de la construcci6n puede ser peligrosa.
Page 28
Neum_ticos: • El inflado excesivo de los neumAticos • Utilice un medidor de presi6n de podria causar lesiones graves y da_o a neumAticos para controlar la presi6n la propiedad, de estos antes de cada uso y mientras los infla; observe el flanco para ver la presi6n correcta del neumAtico.
Page 29
_1__ RIESGO DE OBJETOS DESPEDIDOS COMO EVITARLO _QUE PUEDE SUCEDER? La corriente de aire comprimido puede • Utilice siempre equipo de seguridad provocar lesiones en los tejidos blandos certificado: anteojos de seguridad ANSI de la piel expuesta y puede impulsar Z87.1 (CAN/CSA Z94.3) con protecci6n suciedad, astillas, particulas sueltas y lateral al usar el compresor.
Page 30
RIESGO DE OPERAClON INSEGURA COMO EVITARLO _,QUE PUEDE SUCEDER? La operaci6n insegura de su compresor Revise y comprenda todas las • • de aire podria producir lesiones graves instrucciones y advertencias de este o la muerte, a usted mismo o a otras manual.
Page 31
RIESGO POR RUIDOS _,QU_: PUEDE SUCEDER? COMO EVITARLO periodo de uso, el ruido provocado por certificado: protecci6n auditiva ANSI este producto puede originar p6rdida de $12.6 ($3.19). En determinadas condiciones y segQn el • Utilice siempre equipo de seguridad audici6n. CONSERVE ESTAS INSTRUCCIONES PAPA FUTUPAS...
Page 32
Esta bomba compresora de aire es capaz 50% y el 75%; ello significa que la bomba de funcionar continuamente, sin embargo compresora no deberia trabajar mAs de 30 para prolongar la vida Qtil de su compresor a 45 minutos pot hora. de aire se recomienda mantener un ciclo promedio de servicio que oscile entre el Instale los cuatro tornillos, dos a cada...
Page 33
COMO PREPARAR LA UNIDAD Lubicacibn del compresor de aire • Ubicar el compresor de aire en un corrientes lugar limpio, seco y bien ventilado. conectados El compresor de aire debe colo- a tierra Enchufe Toma- carse alejado per Io menos 30,5 cm (12 pulg.) de las paredes u de cualqui- er otra obstrucci6n que interfiera con...
Page 34
El uso de cables de TRANSPORTE extensi6n el6ctrica AI transportar el compresor en un vehiculo, originara una caida de tensi6n, Io que remolque, etc., asegQrese de que el tanque determinara una p6rdida de potencia del se haya drenado y que la unidad est6 asegu- motor asi como su recalentamiento.
Page 35
CONOZCA SU COMPRESOR DE AIRE LEA ESTE MANUAL DEL PROPIETARIO Y SUS NORMAS DE SEGURIDAD ANTES DE OPERAR LA UNIDAD. Compare las ilustraciones contra su unidad a fin de familiarizarse con la ubicaci6n de los distintos controles y regulaciones. Conserve este manual para ref- erencias futuras.
Page 36
NOTA: Cuando se apag6 la unidad, es nor- Valvula reguladora: Cuando el v_lvula mal que se escuche un silbido breve que indica la salida de aire. compresor de aire se encuentra Antes de ponerlo en marcha funcionando, v&lvula reguladora opere esta esta "abierta", unidad hasta que permitiendo...
Page 37
Antes de cada puesta en marcha C6mo poner en marcha Coloque el interruptor Auto/Off en la Mueva la palanca Auto/Off a la posici6n "Off" y cierre el regulador de posici6n "Auto" y deje que se incre- aire. mente la presi6n del tanque. El motor se detendra una vez alcanzado el valor Tire de la perilla del regulador, gire en sentido antihorario hasta el limite.
Page 38
RESPONSABILIDADES DEL CLIENTE Procedirniento iDiariarnente Diariamente o luego Semanalmente de cada uso Controlar la v_lvula de seguridad Inspeccionar el filtro de aire Drenar el tanque de aire Controlar ruidos o vibra- ciones inusuales Verificar si hay p6rdidas de aire* Limpiar el exterior del compresor Para verificar si hay p6rdidas de aire aplique una solucion de agua jabonosa alred- edor de las juntas.
Page 39
COMO DRENAR EL TANQUE Una vez drenada el agua, cierre la valvula de drenaje (girando en sentido Riesgo de horario). Ahora el compresor de aire operaci6n podrA ser guardado. insegura. Los tanques de aire contienen NOTA: Si la valvula de drenaje fuera del aire de alta presi6n.
Page 40
Tubo unidad cicla autom_ticamente Tubo en cuanto la energfa el_ctrica aliviador salida es conectada. AI efectuar el mantenimiento, usted quedara e×puesto a tensi6n viva, aire comprimido partes en movimiento. Debido a tales circunstancias, podrian ocurrirle lesiones personales. Antes de dar servicio: •...
Page 41
Quite los medidores y el dispositivo de Ensamble el regulador. NOTA: Las fie- conexi6n rApida del reguladon chas indican el flujo de aire. AsegOrese de orientarlo en la direcci6n del flujo de aire. Regulador Regulador Vuelva a aplicar cinta para sellar caSos Quite el regulador.
Page 42
Antes de guardar su compresor de aire, El agua se condensa dentro asegOrese de hacer Io siguiente: del tanque de aire. Si no se drena, eUa Revise ia secci6n "Mantenimiento" corroer_ debilitando la paredes del las paginas precedentes y ejecute el tanque de aire, originando un riesgo de...
Page 43
Riesgo de Operaci6n Insegura. La unidad arranca automAticamente cuando esta enchufada. AI hacer el mantenimiento, el operador puede quedar expuesto a fuentes de corriente y de aire comprimido o a piezas movibles. Antes de intentar hacer reparaciones, desconectar el compresor del tomacorriente, drenar la presi6n de aire del tanque y esperar a que el compresor se enfrie.
Page 44
CORRECClON PROBLEMA CAUSEA Posible defecto en la v&lvula de Golpeteo. Opere la v&lvula de seguridad manualmente tirando de su anillo. seguridad. Si la v&lvula aun pierde, deber& ser reemplazada. Posible defecto en la vAIvula de Reemplace la v&lvula de retenci6n. seguridad.
Page 45
CORRECClON PROBLEMA CAUSEA El motor no Conexiones elOctricas sueltas. Haga inspeccionar por un tOcnico funciona. capacitado de servicio. Posible motor de arranque Haga inspeccionar por un tOcnico defectuosos. capacitado de servicio. Rociado de pintura en las partes Haga inspeccionar por un tOcnico internas del motor.
Agreements Contratos de Protecci6n para Congratulations on making a smart pur- Reparaciones chase. Your new Craftsman ® product Felicitaciones por hacer una compra designed and manufactured for years inteligente. Su nueva unidad Craftsman <"_ of dependable operation. But like all...
Page 48
;iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii! Your Home For repair - in your home - of all major brand appliances, '_iiiiiiiiiiiiiiiiiiiii lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories owner's manuals that you need to do-it-yourself.