Power Source - Craftsman 351.233831 Operator's Manual

• Use recommended accessories (refer to page 17).
Use of improper accessories may cause risk of
injury to persons.
• Handle workpiece correctly.Protect hands from pos-
sible injury.
• Turn machine off if it jams. Knife or bit jams when it
digs too deeply into workpiece. (Motor force keeps it
stuck in the work.)
• Always keep drive, cutterheed and knife guards in
place and in proper operating condition.
• Feed work into knife or cutter against direction of
rotation.
CAUTION: Think safety! Safety is a combinationof
operator common sense and alertness at all times
when tool is being used.
WARNING: Do not attempt to operate tool until it is
completely assembled according to the instructions.
Refer to Figures 15 and 16, pages 16 and 18.
The planer/molder is shipped assembled except for the
handwheel and handle (Figure 16, Key Nos. 22 and 24).
INSTALL HANDWHEEL AND HANDLE
Refer to Figure 16, page 18.
• Handwheel (Key No. 22) must be installed to the left
side of the planer/molder.
• Align handle (Key No. 24) with the hole on the rim of
the handwheel.
• Insert handle screw (Key No. 23) into handle and
tighten to secure.
• Slide handwheel onto crank elevation screw (Key
No. 19) so that the spring pin (Key No. 21) on the
crank elevation screw is positionedbetween the
groove in the handwheel.
REMOVE CAPS
Refer to Figure 15, page 16.
The planer/molder is shipped with caps (Key No. 13) on
the threaded shafts (Key No. 11) to avoid damage to
shafts during shipping and handling.
• Unscrew and remove caps beforeturning the tool on.
• Save caps for future use.
MOUNT PLANER TO WORK SURFACE
Refer to Figure 1.
• Planer is designed to be portable so it can be moved
to job site, but should be mounted to stable, level
bench or table. See Recommended Accessories,
page 17.
MOUNTING INSTRUCTIONS FOR
OPTIONAL STAND MODEL 22250
Refer to Figure 1.
Material List
• ½ x 15 x 22" particle board (not supplied)
• Four 1A-20x 1¼" Bolts with washers and nuts (not
supplied) for mounting board to Multi-Purpose Stand.
• Four 8-1.25 x 30mm boltswith washers (supplied
with planer/molder) for mountingplaner/molder to
board.
A mounting board is needed when mou_ting
planer/molder to Sears Multi-Purpose Stand Model
22250. The mounting board is made from ½" thick ply-
wood or particle board.
• Cut and drill the board using drawing: The 10" diam-
eter hole in the center is used for ventilation only.
• Secure the mounting board to the stand top first,
using four ¼" bolts, washers and nuts (not provided).
be sure board is centered on stand top and bolted
securely.
• Mount the planer/molderto the mounting board
using the four 8-1.25 x 30mm bolts with washers.
Thread the bolts through the mounting board and
into the base casting from underneath the board.
1
Figure I - Mount Planer/Molder to Optional Multi-Purpose
Stand Model No, 22250
POWER SOURCE
WARNING: Do not connect planer/molderto the power
source until all assembly steps have been completed.
The motor Is designed for operation on the voltage and
frequency specified.Normal loads will be handled safe-
ly on voltages not more than 10% abeve or below spec-
ified voltage. Running the unit on voltages which are not
within range may cause overheating an d motor burn-
out. Heavy loads require that voltage at motor terminals
be no less than the voltage specified on nameplate.
• Power supply to the motor is controlledby a rocker
switch. Removing the rocker switchwill lock the unit
and prevent unauthorized use.
3