Table of Contents
Related Manuals for Craftsman 351.286281
Summary of Contents for Craftsman 351.286281
- Page 1 Operator's Manual CRRFTSMRN o 6V_" Bench Top JOINTERJPLANER Model No. 351,286281 Colovos CAUTION: Read and follow all Safety Rules and Operating Instructions before First Use of this Product. Sears Canada Inc., Toronto, Ontario M5B 2B8 2602.03 Draft (04/11/01 )
- Page 2 Consult manual for specific maintaining and adjust- Ing procedures. If within two full years from the date of purcllese, this Craftsman Jolnterlplener falls due to a defect in matedsl • Keep tool lubricated and clean for safest operation, or workmanship, Sears w_LI r epair it free of charge.
- Page 3 • Handle workpiece correctly. Protact hands from pos- sible injury. • Turn machine off if it jams. Blade jams when It digs Refer to Figure 2. too deeply into workpiece. (Motor force keeps it stuck in the work. I ASSEMBLE FENCE BRACKET TO FENCE...
-
Page 4: Power Source
• This tool is equipped with an approved cord rated at 150V and a 3-prong grounding type plug (see Figure 4) for your protection against shock hazards. The Jolnter/piener weighs a pproximately Ibs. when • Grounding plug should be plugged directly into a completely assembled. -
Page 5: Extension Cords
Wires of the extension cord must be of sufficient size DESCRIPTION to carry the current and maintain adequate voltage. Craftsman 6%" jointer/planer is used to s_Jrfacethe faces • Use the table to determine the minimum wire size and edges of boards, produce a fiat surface on warped (A.W.G._ extension cord. -
Page 6: Depth Of Cut
• Use quality lumber. Blades last longer and cuts are Outfeed smoother with good quality wood. Max Depth Table of Cut _/_" • Do not perform jointing/planing operations on materi- al shorter than 8%", narrower than _/4",or !ess than I/_,,thick •... -
Page 7: Blade Guard
CAUTION: Do not slide fence away from the jointer • Place a straightedge over the outfeed table and the blade. body. All sides of the cutterhead must be covered all the time. Back Side of Machine BLADE GUARD Straightedge /_L_"_ The blade guard provides protection over the cuttar- head. -
Page 8: Feeding Workpiece
Feed with the grain whenever possible. With the Grain Rotation Figure 11 • On-Off Switch Againstthe Grain WARNING: Be sure the switch Is In "OFF" position Rotation and the cord is unplugged from the power source before removing switch key. Figure 14 - Dlrecttan of Feed •... - Page 9 • Beveling refers to cutting the entire edge of a board If the blades are nicked they must be replaced or at an angle. Beveling may require several passes reground. They can be reground several times until they become '_lte"wide. due to the depth of cut needed.
-
Page 10: Replacing Timing Belt
Blade • Replace with now timing belt by maintaining inward Cutterhead pressure. Figure lg - Replacing Bladu Replace ADJUSTING BLADE GUARD Figure 21 - Raplacthg Tlmtsg Belt CAUTION: Do not lubricate the pivot point of the b_ade NOTE: Make sure that the full width of bert is on both guard, Oil and lubricating products may contain chemi- pulleys. - Page 11 SYMPTOM CORRECTIVE ACTION POSSIBLE CAUSE(S_) Motor does not start 1. Defective switch 1. Have switch replaced. 2. Defective motor 2. Have motor replacedlrepaired. NOTE: 1 and 2 must be done by a qualified service technician; Consult Sears service. 3. Low line voltage 3.
- Page 12 NOTES...
- Page 13 Model 351.286281 Figure 22 - Replacement Parts Illustration for Motor PART NO. DESCRIPTION QTY. 2856.00 Motor Cover STD315215 6201ZZ Ball Bearing 2857.00 Armature with Fan STD315205 6200ZZ Ball Bearing* 2858.00 Wavy Washer 2859.00 Thread Forming Screw STD852005 5r'nm Lock Washer* 2860.00 Stator 1413.00...
- Page 14 Model 351.286281 Figure 23 - Replacement Parts Illustration for Jointer 41 42...
- Page 15 PART NO. DESCRIPTION QTY. PART NO. DESCRIPTION QTY. Z693.01 Base 2872.00 Shoulder Bolt 4135.00 Foot Pad 9725.00 Wavy Washer 1553.00 Cord Clamp 2869.00 TrunnionHolder Z895.00 1993.00 Thread Forming Screw V,-20 x V_" 3850.00 5-1.0 x 16ram Socket Head Bdt Socket Head Bolt 1903.00 4-0.7 x lOmm _722.00...
- Page 16 SEARS Owner's Manual Sears service is available at or through your Sears Retail Store or Catalogue Sales Office How to order repair parts When ordering repair perts SERVICE AND REPAIR PARTS always give: CALL 1-800-4-MY-HOME* 1. The Part Number 2, The Part Description (%800-469-4663) 3, The Model Number: Keep this number handy should you require a...