Welch Allyn SCANTEAM 2380 WAND Programming Menu Manual
  1. Manuals
  2. Brands
  3. Welch Allyn Manuals
  4. Barcode Reader
  5. SCANTEAM 2380 WAND
  6. Programming menu manual
Welch Allyn SCANTEAM 2380 WAND Programming Menu Manual

Welch Allyn SCANTEAM 2380 WAND Programming Menu Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Programming Menu

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SCANTEAM 2380 WAND and is the answer not in the manual?

Questions and answers

Related Manuals for Welch Allyn SCANTEAM 2380 WAND

Summary of Contents for Welch Allyn SCANTEAM 2380 WAND

  • Page 1 Programming Menu...
  • Page 2 NOTES SCANTEAM 2380 Programming Menu Please Note: The programming features on each menu page are not supported in all models and software revisions of the SCANTEAM 2380. Notations are included if the feature is available only in certain models. Contact your Welch Allyn Sales Coordinator for the revision/model to fit your needs.
  • Page 3 STATUS SCANTEAM 2380/PM Programming Menu CHECK SHOW FIRMWARE REVISION LEVEL Scan the bar code below to display the revision level of the SCANTEAM 2380 firmware. For example: After scanning the Firmware Revision Level bar code, “(C) WA93C” is output to the terminal/host device. The “C” at the end indicates the firmware is at revision level C. Firmware Revision Level SHOW SOFTWARE NUMBER Scan the bar code below to display the SCANTEAM 2380 software number.
  • Page 4 USER’S SCANTEAM 2380 Programming Menu NOTES...
  • Page 5 SYSTEM SCANTEAM 2380/PM Programming Menu GUIDE USE THIS PAGE As a general overview of the programming menu. The programming menu consists of two basic components as shown below. BAR CODE CHART CODE Programming Menu Programming Menu SELECTION II USE THIS PAGE In combination with the adjoining menu pages to program the unit.
  • Page 6 TERMINAL SCANTEAM 2380 Information and Examples SELECTION DIRECT CONNECT ENABLE When enabled, this programming selection allows the wand scanner to replace the keyboard. The scanner will respond the the PC keyboard initialization commands upon power up. This selection is for an AT keyboard only with a terminal ID of 03. LOW POWER When enabled, this programming selection puts the wand scanner in a low power mode.
  • Page 7 TERMINAL SCANTEAM 2380 Programming Menu SELECTION USE THIS PAGE To select the terminal type. To enable the AT Direct Connect feature. To enable the Low Power feature. scan scan terminal selection scan PC/XT ENTER PS/2 model 30 PC/AT, PS/2 50–80 PS/2 30–286 3196/97, 3476/77 3191/92, 3471/72...

  • Page 8: Output Parameters

    OUTPUT PARAMETERS SCANTEAM 2380 Information and Examples & FORMAT SELECTIONS PREAMBLE/POSTAMBLE Preambles and Postambles are characters added by the 2380 to scanned bar code data. These characters are sent with the bar code data to the terminal. Use the Hex–ASCII table below to find the alpha–numeric code to be used for programming a particular Preamble or Postamble.

  • Page 9: Format Selection

    OUTPUT PARAMETERS & FORMAT SELECTION SCANTEAM 2380 Programming Menu USE THIS PAGE To select the pre–programmed asterisked (*) values by scanning DEFAULT symbol. To add preambles and/or postambles to the bar code. To select function transmit enable. To select keyboard type. To set intercharacter, interfunction, and intermessage delays to specific values.
  • Page 10 COMM 1 SCANTEAM 2380 Information and Examples INTERNATIONAL KEYBOARDS The unit aligns the keyboard layout based on the International Keyboard selected here. INTERMEC COMPATIBILITY YES – Allows the unit to be compatible with Intermec keyboard function codes. NO – The default keyboard function codes that are in the preamble and postamble remain active at all times.
  • Page 11 COMM 1 SCANTEAM 2380 Programming Menu USE THIS PAGE To select foreign keyboards. To enable Intermec compatibility scan selections scan variables scan scan INTERNATIONAL France ENTER KEYBOARDS (3) Germany Spain scan Switzerland Italy Sweden (4) DEFAULT Canada (5) Portugal (5) INTERMEC Yes/No* COMPATIBILITY (3)
  • Page 12 SCANCODE SCANTEAM 2380 Information and Examples SELECTION K2 SCANCODE CAPABILITY Reconfigures the 2380 to use K2 (SCANTEAM 2300) compatible scancodes. If other Welch Allyn wedge products are being used or are planned for future use, it is strongly recommended to program this selection for “YES” and use the function codes found in the Keyboard Function Codes Table 2 and Table 3 in the Appendix A.8 of the 2380Technical Manual.
  • Page 13 SCANCODE SCANTEAM 2380 Programming Menu SELECTION USE THIS PAGE (3) To select the pre–programmed asterisked (*) values by scanning DEFAULT symbol. To reconfigure the 2380 to use the 2380 Function Codes. (Applies only to IBM XT, AT, and PS/2’s.) Refer to Appendix A.8 in 2380 Technical Manual for two options. To reconfigure the 2380 to use a new Scancode Table.

  • Page 14: Symbology Selection

    SYMBOLOGY SELECTION SCANTEAM 2380 Information and Examples INDUSTRIAL INDUSTRIAL CODE OUTPUT FORMATS CODABAR . . . Code 3 of 9 bSXX XXCS INTERLEAVED 2 of 5 ..2 of 5 . . . Code 11 .
  • Page 15 SYMBOLOGY SCANTEAM 2380 Programming Menu SELECTION (CODES) USE THIS PAGE To select the pre–programmed asterisked (*) values by scanning DEFAULT symbol. To specify desired bar code symbologies. To select symbology options. selections scan variables scan scan scan CODABAR (ID = a) Enable *Yes/No Minimum Length...
  • Page 16 SYMBOLOGY SELECTION SCANTEAM 2380 Information and Examples RETAIL RETAIL CODE OUTPUT FORMATS Non–Zero Suppressed UPC–A and UPC–E Output Format UPC–A cNXXXXXXXXXXC UPC–A with 2 digit supplemental cNXXXXXXXXXXC–SS UPC–A with 5 digit supplemental cNXXXXXXXXXXC–SSSSS UPC–E cNXXXXXXXXXXC UPC–E with 2 digit supplemental cNXXXXXXXXXXC–SS UPC–E with 5 digit supplemental cNXXXXXXXXXXC–SSSSS...
  • Page 17 SYMBOLOGY SCANTEAM 2380 Programming Menu SELECTION (CODES) USE THIS PAGE To select the pre–programmed asterisked (*) values by scanning DEFAULT symbol. To specify desired bar code symbologies. To select symbology options. selections scan variables scan scan scan CODABAR (ID = a) Enable *Yes/No Minimum Length...
  • Page 18 USER’S SCANTEAM 2380 Programming Menu NOTES...

  • Page 19: Keyboard Layouts

    KEYBOARD LAYOUTS Continued SCANTEAM 2380 Programming Menu IBM XT Keyboard A5 A6 A7 A8 A9 B0 D7 D8 A2 A3 A4 IBM PC/AT Keyboard A9 B0 C7 C8 A1 A2 A3 A4 A5 A6 A7 A8 IBM PS2–30 Keyboard...
  • Page 20 USER’S SCANTEAM 2380 Programming Menu NOTES...

  • Page 21: Sample Bar Codes

    SAMPLE BAR CODES SCANTEAM 2380 Programming Menu This page contains bar code symbols in some of the most commonly used symbologies. You may use these codes to test that your system is properly programmed for a particular symbology. UPC–A 0–3132312078–6 UPC–A 5 add on 0–3132312078–6...
  • Page 22 USER’S SCANTEAM 2380 Programming Menu NOTES...
  • Page 23 USER’S SCANTEAM 2380 Programming Menu NOTES...

  • Page 24: Bar Code Chart

    BAR CODE CHART SCANTEAM 2380 Programming Menu USE THIS PAGE In combination with the adjoining menu pages to program the 2380. The bar codes on this page correspond to symbols in shaded areas on adjoining menu pages. SCAN these bar codes in the sequence indicated on menu page to program desired selections and variables.
  • Page 25 CODE 3 OF 9 SYMBOLS SCANTEAM 2380 Programming Menu FUNCTION RECORD CODES USE THIS PAGE For transmitting functions using function record codes. /C00 /C21 /C11 /C01 /C22 /C12 /C23 /C02 /C13 /C03 /C24 /C14 /C04 /C25 /C15 /C05 /C26 /C16 /C06 /C27 /C17...
  • Page 26 2380/PM Rev K...

Table of Contents