1. Manuals
  2. Brands
  3. Canon Manuals
  4. Printer
  5. MultiPASS F60
  6. Setup sheet

Canon MultiPASS F60 Setup Sheet

Multipass f60 setup sheet
Hide thumbs Also See for MultiPASS F60:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Basic Manual, Software User Manual
READ THIS SHEET FIRST
READ THIS SHEET FIRST
Thank you for purchasing the Canon MultiPASS F60.
To get your machine ready for use, please follow the instructions in this Set-Up Sheet
before referring to any other documentation.
Unpack the machine and its components.
Check that you have the following:
Machine
Paper output tray
PCMCIA card adapter
NOTE
• A printer cable is not included. You must purchase a USB cable (less than 16.4 ft./5 m) to
connect your machine to a computer.
Set-Up Sheet
Set-Up Sheet
Multi-purpose tray
Ink tanks
(Black, cyan, magenta, yellow)
Power cord
Documentation
(Set-Up Sheet, Basic Guide, Extended
Service Plan, Registration Card)
MultiPASS Suite software CD-ROM
Tray cover
Printhead

Advertisement

Table of Contents
loading

Related Manuals for Canon MultiPASS F60

Summary of Contents for Canon MultiPASS F60

  • Page 1 Set-Up Sheet READ THIS SHEET FIRST READ THIS SHEET FIRST Thank you for purchasing the Canon MultiPASS F60. To get your machine ready for use, please follow the instructions in this Set-Up Sheet before referring to any other documentation. Unpack the machine and its components.

  • Page 2: Assemble The Machine

    Remove the shipping material from the machine. Place the machine on a flat surface. Remove all shipping tapes from the exterior of the machine. NOTE • DO NOT remove the USB label A at this stage. USB label A Assemble the machine. Attach the multi-purpose tray.

  • Page 3: Load Paper

    Load paper. q and adjust the Place a stack of paper (print side up) in the multi-purpose tray paper guide A to the width of the stack w. Make sure the stack does not exceed the paper limit mark B. Then place the tray cover C over the multi-purpose tray. Connect the power cord.

  • Page 4: Install The Printhead

    Install the printhead. IMPORTANT • To turn off the machine, be sure to always press [ON/OFF(1sec.)]. This will ensure that the printhead is capped and prevent it from drying up. • If you are not using the machine for a long period of time, we recommend that you print (in black and color) or clean the printhead approximately once a month to maintain the printhead in good working condition.

  • Page 5: Install The Ink Tanks

    Install the ink tanks. Start with the yellow ink tank. Pull the orange tape in the direction of the arrow and remove the plastic wrapper so you can see the air hole A. Turn the ink tank over so that the protective cap B is facing up. Then hold the ink tank as shown below and remove the protective cap B.

  • Page 6: Align The Printhead

    Align the printhead. NOTE • If you will be installing the MultiPASS Suite software, you can also align the printhead from the software. For details, see p. 10-8 of the Basic Guide. When the LCD displays the following, press [Set]. A L I G N P R I N T H E A D P R E S S S E T K E Y The machine will print a horizontal line pattern, and the LCD will display:...

  • Page 7: Install The Software

    Install the software. IMPORTANT • DO NOT connect the USB cable before installing the software. NOTE • When installing the software in Windows XP or Windows 2000, log onto the system as a member of the Administrator group. • If you have previously installed an earlier version of the MultiPASS Suite software (version 4.1 or earlier), you must remove it before installing this version.
  • Page 8 Comprehensive Guide or Software Guide (included in the CD-ROM). Part no. HT3-2121-000-V.2.0 © 2002 Canon Inc. Canon, MultiPASS, and BCI are trademarks of Canon Inc. All other products and brand names are registered trademarks or trademarks of their respective owners.

Table of Contents