Woodstock SHOP FOX W1773 Owner's Manual

37" drum sander
Table of Contents

Advertisement

Quick Links

MODEL W1772/W1773
37" DRUM SANDER
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © OCTOBER, 2007 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in Taiwan
#9083BL

Advertisement

Table of Contents
loading

Summary of Contents for Woodstock SHOP FOX W1773

  • Page 1 OWNER'S MANUAL Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz COPYRIGHT © OCTOBER, 2007 BY WOODSTOCK INTERNATIONAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
  • Page 2 ����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ����������������������������������������������������������������������� ������������������������������������������������������������������������ ������������������������������������������������������������������� ����������������������������������������������������������������� ���������������������������������������������������������������������� ����������������������������������������������� ���������������������������������������������������������������� �������������������������������������������������������������������� ������� �������������������������������������������������������������������� ����������������������������������������������������������������������� ���������������������������������������������������������������������� ������������������������������������� �� ���������������������������� �� ������������������������������������������������������������������ �� ���������������������������������������������������� ������������������������������������������������������������������ ������������������������������������������������������������������ �������������������������������������������������������������������� ��������������������������������������������������������������������� ��������������������������...
  • Page 3: Table Of Contents

    Contents INTRODUCTION ........2 MAINTENANCE ........30 Woodstock Technical Support ....2 General ...........30 W1772 Specificatons ......3 Cleaning ..........30 Lubrication ........30 W1773 Specifications ......5 Controls and Features ......7 SERVICE ..........32 SAFETY ..........8 General ...........32 Standard Safety Instructions ....8 Gauge Blocks ........32...
  • Page 4: Introduction

    Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this product.
  • Page 5: W1772 Specificatons

    W1772/W1773 37" Drum Sander �������� �������������� ���������������������������������������������������������������������������������������������� ����������� ��������������� ������ ������������ ���������������������������������������������������������������������������������������� ������������������������������ ������������������������������������������������������������������������������������������������������������������������� �������� � ��������������������������������������������������������������������������������������������������������������� ����� ����������������������������������������������������������������������������������������������������������������������������� ������������������������������������������������������������������������������������������������������������������������ ��� ������ � ����������������������������������������������������������������������������������������������������������� �������� ����������������������������������������������������������������������������������������������������������������������� ����� ����������������� � ������������������������������������������������������������������������������������������������������ � ����������������������������������������������������������������������������������������������������� ����������������� ��������� � ���������������������������������������������������������������������������������������� ��������������������� ������������� ����������������������������������������������������������������������������������������������������������� �������������� �������������������������������������������������������������������������������������������������������������������...
  • Page 6 W1772/W1773 37" Drum Sander �������������������� ��������������������� ��������������������� � �������������������������������������������������������������������������������������������������� � ���������������������������������������������������������������������������������������������������������������� �� � � � � ��������������������������������������������������������������������������������������������������������������������� ��� � � ����������������������� � ������������������������������������������������������������������������������������������� �� ������������������������������������������������������������������������������������������������������������������ � � � �� ��������������������������������������������������������������������������������������������������������������������� �� � � ������������������������������������������������������������������������������������������������������������� �������� � � ����������������������������������������������������������������������������������������������������������� �������� � � �������������������������������������������������������������������������������������������������������������������� �������������������������������������������������������������������������������������������������������������������������...
  • Page 7: W1773 Specifications

    W1772/W1773 37" Drum Sander �������� �������������� ���������������������������������������������������������������������������������������������� ����������� ��������������� ������ ������������ ����������������������������������������������������������������������������������������������������������� �������������� ������������������������������������������������������������������������������������������������������������������������� �������� � ������������������������������������������������������������������������������������������������������������������ ����������������������������������������������������������������������������������������������������������������������� ���� ���������������������������������������������������������������������������������������������������������������������������� �������������������������������������������������������������������������������������������������������������������������� ������ � ����������������������������������������������������������������������������������������������������������� �������� ����������������������������������������������������������������������������������������������������������������������� ����� ����������������� � ������������������������������������������������������������������������������������������������������ � ����������������������������������������������������������������������������������������������������� ����������������� ��������� � ���������������������������������������������������������������������������������������� ��������������������� ������������� ����������������������������������������������������������������������������������������������������������� �������������� �������������������������������������������������������������������������������������������������������������������...
  • Page 8 W1772/W1773 37" Drum Sander �������������������� ��������������������� ��������������������� � �������������������������������������������������������������������������������������������������� � ���������������������������������������������������������������������������������������������������������������� �� � � � � ��������������������������������������������������������������������������������������������������������������������� ��� � � ����������������������� � ������������������������������������������������������������������������������������������� �� ������������������������������������������������������������������������������������������������������������������ � � � �� � � �������������������� � ����������������������������������������������������������������������������������������������� �� �������������������������������������������������������������������������������������������������������������� �������� � � ����������������������������������������������������������������������������������������������������������� �������� �...
  • Page 9: Controls And Features

    W1772/W1773 37" Drum Sander Controls and Features Figure 1. W1772/W1773 controls and features. A. Micro-Adjust Knob (Left Side) M. Front Drum B. Micro-Adjust Lock (Left Side) N. Gas Strut C. Sanding Drum Motor O. Pressure Roller D. V-Belts P. Emergency Stop Bar E.
  • Page 10: Safety

    W1772/W1773 37" Drum Sander SAFETY READ MANUAL BEFORE OPERATING MACHINE. FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL RESULT IN PERSONAL INJURY. Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.
  • Page 11 W1772/W1773 37" Drum Sander 10. NEVER LEAVE WHEN MACHINE IS RUNNING. Turn power off and allow all moving parts to come to a complete stop before leaving machine unattended. 11. DO NOT USE IN DANGEROUS ENVIRONMENTS. DO NOT use machinery in damp, wet locations, or where any flammable or noxious fumes may exist.
  • Page 12: Additional Safety For Drum Sanders

    W1772/W1773 37" Drum Sander Additional Safety for Drum Sanders READ and understand this USE this and other machinery with caution entire instruction manual and respect. Always consider safety first, before using this machine. as it applies to your individual working Serious personal injury conditions.
  • Page 13: Electrical

    W1772/W1773 37" Drum Sander ELECTRICAL The machine must be properly set up before it is safe to operate. DO NOT connect this machine to the power source until instructed to do so in the "Power Connection" portion of this manual. W1772 Single-Phase 220V Operation Figure 2.
  • Page 14: W1773 220V/440V 3-Phase Operation

    W1772/W1773 37" Drum Sander The machine must be properly set up before it is safe to operate. DO NOT connect this machine to the power source until instructed to do so in the "Power Connection" portion of this manual. W1773 220V/440V 3- Phase Operation Figure 3.
  • Page 15: Rewiring W1773 To 440V

    W1772/W1773 37" Drum Sander Rewiring W1773 to 440V Rewiring your Model W1773 to 440V requires you to replace the existing control box 220V main panel with a 440V main panel and rewire the sanding motor and feed motor. The 440V conversion kit can be purchased as #X1773553 by calling (360) 734-3482.
  • Page 16: Setup

    W1772/W1773 37" Drum Sander SETUP Unpacking This machine has been carefully packaged for safe trans- SUFFOCATION HAZARD! portation. If you notice the machine has been damaged Immediately discard all during shipping, please contact your authorized Shop Fox plastic bags and pack- dealer immediately.
  • Page 17: Assembly

    W1772/W1773 37" Drum Sander Assembly To attach the top cover, control panel, and handwheel to the drum sander, do these steps: 1. Remove the six button head cap screws from the top cover shown in Figure 7, and remove the two lock knobs shown in Figure 8.
  • Page 18 W1772/W1773 37" Drum Sander Remove the bolts, flat washers, and hex nuts from the control panel support arm, as shown in Figure 10. 8. Remove the right access panel. With assistance, lift the control panel into place and secure it with the bolts, flat washers, and hex nuts removed in Step 7.
  • Page 19: Machine Placement

    W1772/W1773 37" Drum Sander Machine Placement • Floor Load: This machine distributes a heavy load in The Model W1772/W1773 a small footprint. Some residential floors may require is an extremely heavy additional bracing to support both machine and machine. Serious per- operator.
  • Page 20: Lifting Sander

    W1772/W1773 37" Drum Sander Lifting Sander To place the sander in a permanent location, do these steps. 1. Unbolt the sander from the pallet. 2. Position the forklift forks directly above the sander. Place two lifting straps with hooks on the ends over the forklift forks and slide the hooks into the eye- bolts shown in Figure 14.
  • Page 21: Dust Collection

    W1772/W1773 37" Drum Sander Dust Collection Recommended CFM at Sander: ....1600 CFM Do not confuse this CFM recommendation with the rating of the dust collector. To determine the CFM at the dust port, you must take into account many variables, includ- ing the CFM rating of the dust collector, the length of hose between the dust collector and the machine, the amount of branches or Y's, and the amount of other open...
  • Page 22: Gear Oil Check

    W1772/W1773 37" Drum Sander 2. Feed the power wires through the strain relief on the bottom of the control panel, tighten the strain relief, connect the cord to the terminals shown in Figure 18 or 19, and reinstall the control panel face plate.
  • Page 23: Test Run

    W1772/W1773 37" Drum Sander Test Run Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular opera- tion. The test run consists of verifying the following: 1) The motors power up and run correctly, 2) the motors turn the correct direction (machine is not wired out of phase (W1773 only), and 3) the stop button safety feature works correctly.
  • Page 24: Recommended Adjustments

    W1772/W1773 37" Drum Sander — If the top of the conveyor belt rotates The STOP button safety feature is not toward the front of the machine, it is working correctly. This safety feature moving in the wrong direction. Stop the must work properly before proceed- machine, shut OFF the power source, ing with regular operations.
  • Page 25: Operations

    W1772/W1773 37" Drum Sander OPERATIONS Control Panel Below is a summary of your sander control panel and the components that it controls. Use the list with Figure 23 to become familiar with your sander. A. Sanding Drums Start Button: Starts the sanding drums.
  • Page 26: Depth Of Cut

    W1772/W1773 37" Drum Sander Depth of Cut The optimum depth of cut will vary based on the type of wood, feed rate, and sandpaper grit. Under most sand- ing conditions, the depth should not exceed " (approx. turn of the handwheel). Each full turn of the table height handwheel raises the conveyor table approximately 0.020".
  • Page 27: Using The Amp Draw Meter

    W1772/W1773 37" Drum Sander Using the Amp Draw Meter 26) is used to keep The amp draw meter (Figure machine from being overloaded during sanding operations. As a general rule, always start with a shallow sand- ing depth and carefully increase the sanding depth. Keep the amp load in the green range during operation.
  • Page 28: Sanding Tips

    W1772/W1773 37" Drum Sander Sanding Tips • Replace the sandpaper with a higher grit to achieve a finer finish. • Raise the table with a maximum of turn of the height handle until the workpiece is the desired thickness. • Reduce snipe when sanding more than one board of the same thickness by feeding them into the sander with the front end of the second board touching the...
  • Page 29: Choosing Sandpaper

    W1772/W1773 37" Drum Sander Choosing Sandpaper There are many types of sanding belts to choose from. Grit Class Usage We recommend Aluminum Oxide for general workshop Extra Coarse Rough sawn environments. To the side is a chart that groups abrasives boards, thick- into different classes, and shows which grits fall into each ness sand-...
  • Page 30: Paper Replacement

    W1772/W1773 37" Drum Sander Paper Replacement NOTICE The Model W1772/W1773 is designed for 6" wide sandpa- Turn to SECTION 5: ACCESSORIES on per rolls. Page 29 for grit selection and model numbers. To change the paper, do these steps: 1. DISCONNECT POWER TO THE SANDER! Tension Spring Cap Screw Tool...
  • Page 31: Drum Sander Accessories

    Dealer. If you do not have a dealer in your area, these products are also available through online deal- ers. Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of deal- ers at: 1-800-545-8420 or at sales@woodstockint.com.
  • Page 32: Maintenance

    W1772/W1773 37" Drum Sander MAINTENANCE General Regular periodic maintenance on your Model W1772/ W1773 will ensure its optimum performance. Make a habit of inspecting your machine each time you use it. Check for the following conditions and repair or replace when necessary: •...
  • Page 33 W1772/W1773 37" Drum Sander 2. Remove the feed motor cover, loosen the four hex bolts (Figure 34) that secure the gear box to the motor bracket, and remove the V-belt. 3. With the oil and gearbox warm, slide the gearbox Fill Plug out, remove the fill plug (Figure 34), remove the drain plug, drain the oil, and reinstall the drain...
  • Page 34: Service

    If you require additional machine service not included in this section, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.biz. Gauge Blocks...
  • Page 35: V-Belt Service

    W1772/W1773 37" Drum Sander V-Belt Service Tension New V-belts often stretch and loosen up during the first 16 hours of use. After this period, they should be inspect- ed and re-tensioned if necessary. Proper tension is important for optimum power transmis- sion.
  • Page 36: Bearing Replacement

    W1772/W1773 37" Drum Sander Each pulley can be adjusted by loosening the set screw that secures the pulley to the shaft, sliding the pulley in/ out, and retightening the set screw to lock the pulley in place. To align the pulleys, do these steps: 1.
  • Page 37 W1772/W1773 37" Drum Sander 5. Use a screwdriver to pry and rotate the bearing so it Mounting Flange is horizontal to the bearing-housing mounting flang- es, as shown in Figure 43. 6. Slide the bearing out of the bearing housing, as shown in Figure 44.
  • Page 38: Conveyor Tensioning & Tracking

    W1772/W1773 37" Drum Sander Conveyor Tensioning & Tracking Tensioning The conveyor may slightly stretch with continued use and will eventually need to be tensioned. This is most obvious if the conveyor starts slipping on the rollers. When you tension the conveyor, focus on turning the adjustment bolts in even increments.
  • Page 39 W1772/W1773 37" Drum Sander Tracking If the conveyor tracks to either side, then the tracking must be corrected or the conveyor will load up to one side and could rip or tear and have to be replaced. Replacing a damaged conveyor is a big job. Always be careful to make sure that the belt does not travel too far to one side or the other.
  • Page 40: Drum Adjustments

    W1772/W1773 37" Drum Sander Drum Adjustments There are three adjustments for the sanding drums: 1) the drums must be perpendicular to the feed direction (par- allel with the conveyor roller, Figure 49); 2) the drums must be parallel to the top of the conveyor belt (Figure 54, Page 40);...
  • Page 41 W1772/W1773 37" Drum Sander — If the difference between the two measurements Front Drum Rear Drum at each end is more than ⁄ ", continue to the next step. Set Screws 6. Loosen the rear drum pillow bearing lock nuts, shown in Figure 51.
  • Page 42 W1772/W1773 37" Drum Sander Adjusting Drum Height & Drum-to-Conveyor ������� Parallelism The rear drum can be adjusted parallel to the conveyor ������������ belt in fine increments at the pillow bearings with the � � micro-adjust knobs, or the front drum can be adjusted �������������...
  • Page 43 W1772/W1773 37" Drum Sander 5. Loosen the lock lever or lock handle (see Figures 56 & 57) at one end of the rear drum. 6. Turn the micro-adjustment knob until a 0.010" feeler Micro-Adjust gauge fits between the drum and gauge board (Figure Knob 58).
  • Page 44: Pressure Roller Height

    W1772/W1773 37" Drum Sander Pressure Roller Height The pressure rollers are factory set at 0.039"–0.078" below the bottom of the rear sanding drum and are fully adjust- able either up/down with the lock nuts shown in Figure Proper pressure on the workpiece helps avoid kickback and keeps the workpiece from slipping.
  • Page 45: Scale Pointer Calibration

    W1772/W1773 37" Drum Sander Scale Pointer Calibration For the scale pointer to be accurate, it must be calibrat- We recommend calibrating your scale pointer any time you adjust the drum heights or table lift screws. To calibrate the scale pointer, do these steps: 1.
  • Page 46 W1772/W1773 37" Drum Sander Each tooth on the sprocket represents 0.006" of table elevation movement. For example, if the rear of the table was 0.006" low, rotate both rear table lift screws to the next sprocket tooth in the same chain position. You can easily rotate the sprockets from the top of the table lift screws with a flat head screwdriver.
  • Page 47: W1772/W1773 Wiring Overview

    W1772/W1773 37" Drum Sander W1772/W1773 Wiring Overview ��������� ������������� ����� �� ������������������������ ����� �� ���������������������������� ��������������������������� ��� �� ����������������������������� ����� �� ������������������������ Figure 65. Emergency stop bar limit switch. �� �� ���������� �������� � � � ������������ ��� �� �� Figure 65.
  • Page 48: W1772/W1773 Control Panel

    W1772/W1773 37" Drum Sander W1772/W1773 Control Panel ��������� ������������� ����� �� ��� �� ��������� ����� �� �� �� ���� ���� ����� ������ �������� ����� ������������� ������������������������ ����� ����� ���������������������������� ��������������������������� � � � � �� �� �� �� ����������������������������� ������������������������ ��...
  • Page 49: W1772 Electrical Box 220V, 1-Ph

    W1772/W1773 37" Drum Sander W1772 Electrical Box 220V, 1-Ph Main Panel Feed Motor Contactor Sanding Motor Contactor Feed Motor Relay Current (dial @ 2.7A) Sensor Sanding Motor Relay (dial @ 43A Incoming Control Panel Power Terminal Block Terminal Block Ground Figure 68.
  • Page 50: W1772 Electrical Box Wiring 220V, 1-Ph

    W1772/W1773 37" Drum Sander W1772 Electrical Box Wiring 220V, 1-Ph �� �� �� �� �� � �� �� �� �� � �� � �� � �� �� �� �� ���� ���� ���� � � ���� ���� ���� � � �� ��...
  • Page 51: W1772 Sanding & Feed Motors

    W1772/W1773 37" Drum Sander W1772 Sanding & Feed Motors ��� ��������� �� � � � � �� ����� �� ������ �� �� �� �� �� ��� �� ��������� ����� ������ �� �� ����� �� ��������� ������ Figure 69. W1772 sanding drum motor ��...
  • Page 52: W1773 Electrical Box 220V, 3-Phase

    W1772/W1773 37" Drum Sander W1773 Electrical Box 220V, 3-Phase Main Panel Feed Motor Sanding Motor Sanding Motor Relay Contactor Contactor (dial @ 43A) Current Sensor Incoming Power Terminal Block Feed Motor Relay (dial @ 1.3A) Ground Control Panel Terminal Block Figure 75.
  • Page 53: W1773 Electrical Box Wiring 220V, 3-Phase

    W1772/W1773 37" Drum Sander W1773 Electrical Box Wiring 220V, 3-Phase �� �� �� �� �� �� � �� �� �� �� � � �� � �� �� �� �� �� �� ���� ���� ���� � � ���� ���� ���� � ��...
  • Page 54: W1773 Electrical Box 440V, 3-Phase

    W1772/W1773 37" Drum Sander W1773 Electrical Box 440V, 3-Phase Sanding Sanding Motor Motor Amp Meter Relay Feed Motor Contactor Transformer (dial @ 21.5A) Contactor Main Panel Current Sansor Feed Motor Relay (dial @ 0.65A) Incoming Power Terminal Block Control Panel Terminal Block Figure 76.
  • Page 55: W1773 Electrical Box Wiring 440V, 3-Phase

    W1772/W1773 37" Drum Sander W1773 Electrical Box Wiring 440V, 3-Phase ��������� �� �� � � ����� �� � �� �� �� ���� ����� ������ ����������� �� ����� �� �� �� �� ��� �� ���� �� �� �� �� �� �� �...
  • Page 56: W1773 Sanding Drum Motor

    W1772/W1773 37" Drum Sander W1773 Sanding Drum Motor Figure 77. W1773 220V sanding drum motor Figure 78. W1773 440 sanding drum motor wiring. wiring. ����� ��� ������������� ����� �� ������������������������ �� ����� ���������������������������� ��������������������������� �� ����� ����������������������������� �� ��� ������������������������ ����...
  • Page 57: W1773 Feed Motor

    W1772/W1773 37" Drum Sander W1773 Feed Motor Figure 79. W1773 220V feed motor wiring. Figure 80. W1773 440 feed drum motor wiring. ����� ��� ������������� ����� �� ������������������������ �� ����� ���������������������������� ��������������������������� �� ����� ����������������������������� �� ��� ������������������������ ���� ���� �...
  • Page 58: Troubleshooting

    W1772/W1773 37" Drum Sander Troubleshooting This section covers the most common problems and corrections with this type of machine. WARNING! DO NOT make any adjustments until power is disconnected and moving parts have come to a complete stop! Motor & Electrical PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION...
  • Page 59 W1772/W1773 37" Drum Sander Machine Operations PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Machine slows when sand- 1. V-belts loose. 1. Tighten V-belts (Page 33). ing, making squealing noise, 2. V-belts worn out. 2. Replace V-belts (Page 33). especially on start-up. 1. Pulley setscrews or keys are missing 1.
  • Page 60: Parts

    W1772/W1773 37" Drum Sander PARTS Frame Parts Breakdown PART�# DESCRIPTION PART�# DESCRIPTION X1772101 MAIN�FRAME XPN09M HEX�NUT�M12-1.75 X1772102 LIFT�RING X1772111 SANDING�DRUM�MOTOR�10HP�1PH�(W1772) X1772103 SCALE X1773111 SANDING�DRUM�MOTOR�15HP�3PH�(W1773) X1772105 MOTOR�BASE 111-1 X1772111-1 MOTOR�COVER�(W1772) XPB75M HEX�BOLT�M12-1.75�X�35 111-1 X1773111-1 MOTOR�COVER�(W1773) XPN09M HEX�NUT�M12-1.75 111-2 X1772111-2 MOTOR�FAN�(W1772) XPB143M HEX�BOLT�M12-1.75�X�120 111-2 X1773111-2 MOTOR�FAN�(W1773) XPW01...
  • Page 61: Frame Parts List

    W1772/W1773 37" Drum Sander Frame Parts List PART�# DESCRIPTION PART�# DESCRIPTION 111-4 X1772111-4 CAPACITOR�COVER�(W1772) X1772168 HINGE 111-5 X1772111-5 JUNCTION�BOX�(W1772) XPSBS09M BUTTON�HD�CAP�SCR�M6-1�X�12 111-5 X1773111-5 JUNCTION�BOX�(W1773) X1772170 KNOB�M6-1�X�12 111-6 X1772111-6 S.�CAP�300M�250V�45�X�97�(W1772) X1772171 WHEEL�HANDLE 111-8 X1772111-8 CENTRIFUGAL�SWITCH�(W1772) XPSS09 SET�SCREW�3/8-16�X�1/2 XPK109M KEY�7�X�7�X�35 X1772173 HANDWHEEL XPB116M HEX�BOLT�M10-1.5�X�45 X1772174...
  • Page 62: Conveyor Parts Breakdown

    W1772/W1773 37" Drum Sander Conveyor Parts Breakdown -60-...
  • Page 63: Conveyor Parts List

    W1772/W1773 37" Drum Sander Conveyor Parts List PART�# DESCRIPTION PART�# DESCRIPTION XPN28M HEX�NUT�M20-2.5 X1772233 COLLAR X1772186 TABLE X1772234 COMPRESSION�SPRING X1772187 TABLE�SUPPORT X1772235 PULLEY X1772188 TABLE�SUPPORT X1772236 V-BELT�AX-25 XPB26M HEX�BOLT�M8-1.25�X�30 X1772237 PULLEY XPLW01 LOCK�WASHER�5/16 X1772238 FEED�MOTOR�1/3HP�220V�1PH�(W1772) X1772191 ROLLER�SUPPORT�BRACKET X1773238 FEED�MOTOR�1/3HP�220/440V�3PH�(W1773)� X1772192 ROLLER�SUPPORT�BRACKET 238-1 X1772238-1 MOTOR�FAN�COVER�(W1772) XPB26M...
  • Page 64: Roller & Drum Parts Breakdown

    W1772/W1773 37" Drum Sander Roller & Drum Parts Breakdown ��� ��� ��� ����� ��� ��� ��� ��� ����� ��� ��� ��� ����� ����� ��� ��� ����� ��� ��� ��� ��� ��� ����� ��� ��� ��� ��� ��� ��� ��� ��� ���...
  • Page 65: Micro-Adjustment Breakdown

    W1772/W1773 37" Drum Sander Micro-Adjustment Breakdown ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ���...
  • Page 66: Electrical Components

    W1772/W1773 37" Drum Sander Electrical Components ��� ��� ��������� �� �� �� ���� ���� ���� � �� ���� ���� ���� �������������������� � �� ������������������� �������� ����� ��� ��� ��������������� ���� ����� ����� �������� ��� ����� �������� ���� ���� ���� � ����...
  • Page 67: Electrical Parts List

    W1772/W1773 37" Drum Sander Electrical Parts List PART�# DESCRIPTION PART�# DESCRIPTION X1772541 CURRENT�SENSOR X1773547 INCOMING�POWER�TERMINAL�BLOCK�(W1773) X1772542 CONTACTOR�SDE�MA-55�220V�(W1772) X1772549 AMP�METER�TRANSFORMER X1772542 CONTACTOR�SDE�MA-55�220V�(W1773,�220V) X1773553 W1773�220/440V�CONVERSION�KIT�15HP 542A X1773542A CONTACTOR�SDE�MA-30�220V�(W1773,�440V) X1772555 MAIN�ELECTRIC�PANEL�(W1772) X1772543 OL�RELAY�SDE�RA-60�32~50�(W1772) X1773555 MAIN�ELECTRIC�PANEL�(W1773,�220V) X1773543 OL�RELAY�SDE�RA-60�32~50�(W1773,�220V) 555A X1773555A MAIN�ELECTRIC�PANEL�(W1773,�440V) 543A X1773543A OL�RELAY�SDE�RA-30�19~26�(W1773,�440V) X1772556 CONTROL�PANEL�PLATE X1772544...
  • Page 68: Label Placement

    MUST maintain the original location and readability of all labels on this machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www. shopfoxtools.com to order new labels.
  • Page 69: Warranty Registration

    W1772/W1773 37" Drum Sander Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services.
  • Page 70 FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE...
  • Page 71 ® with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under this warranty exceed the purchase price paid for the product, and any legal actions brought against Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special or consequential damages arising from the use of our products.

This manual is also suitable for:

Shop fox w1772

Table of Contents