Page 2
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. •...
INTRODUCTION ...2 About Your New Disc Sander ...2 Woodstock Service and Support ...2 Warranty and Returns ...3 Specifications ...3 SAFETY FIRST!...4 Standard Safety Instructions ...4 Disc Sander Components ...6 Additional Safety Instructions for Disc Sanders ...7 110V Operation ...8 Extension Cords ...8 Grounding ...8...
The Model W1708 is a very versatile and easy to use disc sander. This machine can perform a wide variety of sanding operations. This disc sander features a 1 HP motor, a tilting cast iron table, a miter gauge, a built in 2"...
Woodstock International, Inc. Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX machine or machine part which in normal use has proven to be defective, provided that the original...
SAFETY FIRST! READ MANUAL BEFORE OPERATING MACHINE. FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL RESULT IN PERSONAL INJURY. Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.
Page 7
13. Use the correct tool. Do not force the tool or attachment to do a job for which it was not designed. 14. Wear proper apparel. Do not wear loose clothing, gloves, jewelry, keep long hair tied up, etc. 15. Remove adjusting keys and wrenches. Before turning the machine on, make a habit of checking that all adjusting keys and wrenches have been removed before turning the machine ON.
Electrical Requirements 110V Operation The SHOP FOX ® W1708 has a 1 HP, 110V, 60 Hz motor that draws approximately 10 amps under load. Use a 15 amp circuit breaker in a circuit that has wiring rated to handle this amperage draw.
Overview The following is a description of the components shipped with the SHOP FOX W1708 12" Disc Sander. Should any parts be missing, examine the packaging carefully to be sure parts are not among the packing materials. If any parts are missing, contact Woodstock International, Inc.
Cleaning Machine The unpainted parts of the Model W1708 are coated with a waxy grease that protects them from corrosion during shipment. For optimum performance from your machine, make sure you clean all moving parts or sliding contact surfaces that are coated. Clean this grease off with a solvent cleaner or citrus-based degreaser.
ADJUSTMENTS General Information The adjustments in this section have been preset and generally do not need to be performed when you first receive your disc sander; however, we suggest that you become familiar with these adjustments before operating your disc sander. This will help you understand the machine and will prepare you for the types of adjustments that can be made in troubleshooting and everyday use.
Figure 7. Checking table tilt. Figure 8. Slide covered sandpaper between disc and table. Figure 9. Remove paper backing Table Tilt To ensure accuracy, adjust the table 90˚ to the sanding disc. To check table tilt, do these steps: 1. Place a try square or a machinist’s square with the base flat against the table and the blade vertical against the disc plate.
Test Run Once the adjustments are complete, the SHOP W1708 is ready for a test run. The ® purpose of a test run is to identify any unusual noises and vibrations, as well as to confirm that the machine is performing as intended.
Miter Sanding An effective way of making a perfect miter is to cut the workpiece slightly long and sand it to the desired angle. To perform miter sanding operations, do these steps: 1. Loosen the knob on the miter gauge, adjust the miter gauge body to the desired angle and tighten the knob.
MAINTENANCE General Regular periodic maintenance on your Model W1708 will ensure its optimum performance. Make a habit of inspecting your sander each time you use it. Check for the following conditions and repair or replace when necessary. Loose mounting bolts.
General Information. The specifications, drawings, and photographs illustrated in this manual represent the Model W1708 as supplied when the manual was prepared. However, due to Woodstock International, Inc.’s policy of continuous improvement, changes may be made at any time with no obligation on the part of Woodstock International, Inc.
PART # DESCRIPTION X1708001 SHOP FOX LOGO LABEL X1708002 READ MANUAL LABEL X1708003 SAFETY GLASSES LABEL X1708004 MACHINE ID LABEL X1708005 MOTOR 1HP X1708005-1 MOTOR FAN X1708005-2 FAN COVER X1708005-3 WIRING BOX XPC100A CAPACITOR 100MFD/250V X1708005-5 CAPACITOR COVER XPTLW01M EXT TOOTH WASHER 4MM XPLW01M LOCK WASHER 5MM X1708008...
Page 21
___Miter Saw ___Other__________________________________________________ What machines/supplies would you like to see? _________________________________________________________ _________________________________________________________ _________________________________________________________ _________________________________________________________ What new accessories would you like Woodstock International to carry? _________________________________________________________ _________________________________________________________ Do you think your purchase represents good value? ___Yes Would you recommend SHOP FOX ___Yes...
Page 22
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE WOODSTOCK INTERNATIONAL, INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...