Advertisement
Available languages
Available languages
INSTALLATION
Installation
Television
Location
Follow
these
recommendations
before
deciding
on
the
location
of your television.
•
Avoid
excessive
sunlight
or bright
lights,
including
reflections.
•
Keep away from excessive heat or moisture. Inadequate
ventilation may cause internal component failure.
•
Fluorescent
lighting
may
reduce
remote
control
transmitting range.
•
Keep away from magnetic equipment,
including motors,
fans and external speakers.
WARNING:
Use this television receiver only with the
cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart
is used, use caution when moving the cart/apparatus
combination
to avoid injury from tip-over. In order to
avoid injury to children, never place your television receiver on a
piece of furniture that is capable of being tilted by a child leaning
on it, pulling on it, standing
on it, or climbing
on it. A falling
television can cause serious injury or even death.
CT-32SC15, CT-32SC15U:
CAUTION:
These
television
receivers
for use only with
PANASONIC
TY-32SC15T
stand.
Use with other carts (or
stands) is capable of resulting in instability causing possible
injury.
CT-32SL15, CT-32SL15U:
CAUTION:
These
television
receivers
for
use only with
PANASONIC
TY-32HL15T
stand.
Use with other carts (or
stands) is capable of resulting in instability causing possible
injury.
Optional
Cable Connections
Shielded
audio
and video
cables
should
be used between
components.
For best results:
•
Use 75-ohm coaxial shielded cables.
•
Use appropriate input and output connectors that match
your component connectors.
•
Avoid long cables to minimize interference.
AC Power Supply Cord
CAUT,ON"
TO PREVENT
ELECTR,C
SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT
OF AC OUTLET AND FULLY INSERT. DO NOT
Polarized
plug
USE A PLUG WITH A RECEPTACLE OR OTHER
OUTLET UNLESS THE BLADE CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
PROTECT
POWER
CORDS
FROM
BEING
WALKED
ON, ROLLED
OVER, CRIMPED,
BENT, OR PINCHED,
PARTICULARLY
AT PLUGS,
CONVENIENCE
RECEPTACLES,
AND THE POINT WHERE THEY EXIT
FROM THE APPARATUS.
Cable / Antenna
Connection
For proper
reception,
either
a cable or antenna
connection
is required.
Cable Connection
Connect the cable supplied by your local
cable company. Tighten with fingers only.
Use of any tool (e.g. pliers) for tightening
may result in tuner damage.
Note:
A cable
converter
box may be
required
for
proper
reception.
Check
with
your
local
cable
company
for compatibility requirements.
Incoming
Cable from
Cable Company
75 Ohm VHF/UHF
on back of TV
Antenna Connections
Note:
•
For proper reception of VHF/
IncomingCablefrom
UHF channels,
an external
Home Antenna
antenna is required. For best
r_
_
reception an outdoor antenna
is recommended.
Cable
Mode
is
preset
at
the
factory.
Antenna
users
must
change to TV Mode in the Set Up menu under Prog
Chan (page 9).
Remote
Control
Battery
Installation
Requires
two AA batteries
(supplied).
Battery
Polarity
©
®
Procedure
1.
Turn the remote control face down. Remove battery
cover by pressing down on the marking on the cover
and sliding it off in the direction indicated.
2.
Install batteries matching (+) and (-) polarity signs.
3.
Replace the battery cover by sliding it in reverse until
the lock snaps.
Note:
Incorrect installation can cause battery leakage and
corrosion that will damage the Remote Control.
Precautions
•
Replace batteries in pairs.
•
Do not mix battery types (zinc carbon with alkaline).
•
Do not recharge, heat, short-circuit, disassemble, or
burn batteries.
40
Advertisement
Chapters
