GE ZFSB23D SS Installation Instructions Manual

Free-standing side-by-side stainless steel refrigerator

Advertisement

Quick Links

Installation
Instructions
If you have questions, call 800-GE-CARES or visit our website at: www.monogram.com
Free-Standing Side-by-Side
Stainless Steel Refrigerator
ZFSB23D SS
Monogram.
We bring good things to life.
®

Advertisement

Table of Contents
loading

Summary of Contents for GE ZFSB23D SS

  • Page 1 Installation Instructions If you have questions, call 800-GE-CARES or visit our website at: www.monogram.com Free-Standing Side-by-Side Stainless Steel Refrigerator ZFSB23D SS Monogram. ® We bring good things to life.
  • Page 2: Table Of Contents

    • Il faut débrancher le réfrigérateur avant le failure due to improper installation is not covered nettoyage ou toute intervention. under the GE Appliance Warranty. See the Owner’s • Les réparations doivent être faites par un Manual for warranty information.
  • Page 3: Product Dimensions And Clearances

    Planning Information PRODUCT DIMENSIONS THE INSTALLATION SPACE AND CLEARANCES The opening width must be 36-1/2". 27-1/2" Case 36-1/2" Depth Wall View Electrical Area 72" 73" min. Water Supply 36" Water And Electrical Locations 29-1/2" The opening must be prepared with the electrical and Including Handles water supply located as shown.
  • Page 4: Installation Instructions

    Installation Instructions TOOLS REQUIRED FLOORING For proper installation, this refrigerator must be placed • Tinsnips to cut banding on a level surface of hard material that is at the same • Stepladder • Bucket height as the rest of the flooring. This surface should be •...
  • Page 5: Step 1 Move Refrigerator Indoors

    Installation Instructions REMOVE THE DOORS STEP 1 MOVE REFRIGERATOR INDOORS The top cap must be removed to access hinges. It is best to remove one door at a time. A. Remove two screws on top of the refrigerator, one on IMPORTANT: Door and passageways into each side.
  • Page 6: Step 2 Install Water Line

    3 coils of about 10". Outlet Valve Ferrule (Sleeve) NOTE: The only GE approved plastic tubing is sup- plied in GE SmartConnect™ Refrigerator Tubing kits. Do not use any other plastic water supply line because • Drill a 1/4" hole in the water pipe.
  • Page 7: Step 2A, Ro Water Line

    Tubing Clamp IMPORTANT: 1/4" Compression Nut When connecting to a GE reverse osmosis water Ferrule system to your refrigerator, the GE RVKit must be (sleeve) used. For other reverse osmosis water systems, follow the manufacturer’s recommendations. Refrigerator Connection SmartConnect™ Tubing If the water supply to the refrigerator is from a Reverse Osmosis Water System, use the refrigerator’s...
  • Page 8: Step 6 Level Refrigerator

    Installation Instructions STEP 7 LEVEL THE DOORS STEP 6 LEVEL REFRIGERATOR If the doors are not evenly aligned at the top, the The refrigerator can be leveled by adjusting the refrigerator door can be adjusted. rollers located near the bottom hinges. •...
  • Page 9: Step 8 Start Icemaker

    Installation Instructions STEP 9 TEMPERATURE STEP 8 START ICEMAKER CONTROLS • The temperature controls are preset at 37° for the Power Switch refrigerator and 0°F for the freezer. • Allow 24 hours to stabilize before making adjustments. STEP 10 INSTALL TOEKICK Feeler Arm •...
  • Page 10 Notes...
  • Page 11 Notes...
  • Page 12 General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Monogram. ® We bring good things to life. GE Consumer Products Pub. No. 49-60227-1 General Electric Company Louisville, KY 40225 Dwg. No. 197D5335P001 ©2003 General Electric Company...

Table of Contents