12.0-volt lithium-ion cordless 3/8 in. reversible drill (18 pages)
Summary of Contents for Craftsman 315.114610
• Operation Safety Rules and Operating Instructions • Maintenance before first use of this product. • Parts List Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 Visit the Craftsman web page: www.sears.com 983000-341 6-03...
Exploded View And Repair Parts List .......................... • Parts Ordering / Service ............................... FULL ONE YEAR WARRANTY ON CRAFTSMAN 3/8 in. CORDLESS DRILL-DRIVER If this CRnFTSMRN 3/8 in. Cordless Drill-Driver fails to give complete satisfaction within one year from the date of pur- chase, RETURN IT TO THE NEAREST SEARS STORE OR SEARS SERVICE CENTER IN THE UNITED STATES, and Sears will repair it, free of charge.
• Your drill-driver has many features for making your drilling CAUTION: Carefully read through this entire operations more pleasant and enjoyable. Safety, operator's manual before using your new drill-driver. performance and dependability have been given top Pay close attention to the General Safety Rules, priority in the design of this drill-driver making it easy to Specific Safety Rules and Symbols, Warnings and maintain and operate.
• Maintain tools with care. Keep cutting tools sharp cleaning. Never use brake fluids, gasoline, petroleum- and clean. Properly maintained tools with sharp cutting based products, or any strong solvents to clean your edges are less likely to bind and are easier to control. tool.
c. That wire size is large enough for AC ampere WARNING: rating of charger as specified below: Read and understand all instructions. Failure to follow all instructionslisted below, may result in electric Cord Length (Feet) 100' shock, fire and/or serious personal injury. Cord Size (AWG) Note: AWG = American Wire Gage •...
Important:Someofthefollowing symbols m aybeusedonyourtool.Please study themandlearn theirmeaning. Proper interpretation of thesesymbols w illallowyoutooperate thetoolbetter andsafer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Amperes Current Hertz Frequency (cycles per second) Minutes Time Alternating Current Type or a characteristic of current Direct Current Type or a characteristic of current No Load Speed Rotational speed, at no load...
DRILL-DRIVER 315.114610 Maximum Torque 337 in.lb. Chuck 3/8 in. Keyiess CHARGER Item No. 9 11379 Motor DC Motor 18 Volt (1426161 ) Gear Train Two Speed Rating 120 V, 60 Hz, AC only No Load Speed 0-350/min. (Low) Charging Voltage 18 Volt 0-1300/min (High) Charge Rate...
TWO-SPEED LEVEL GEARTRAIN(HI-LO) TORQUE KEYLESS ADJUSTMENT CHUCK RING REARVIEW DIRECTION OF ROTATION SELECTOR BATTERYPACKSHOWN (FORWARD/REVERSE) IN CHARGING STAND SWITCH TRIGGER STORAGE CHARGER SCREWDRIVER BITS BATTERYPAq SHOWNINTOOL WRIST STRAP Fig. I...
remain on until battery pack is removed from charging WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. stand or the charger is disconnected from power Failure to do so could result in objects being thrown supply.
SWITCH TO INSTALL BATTERY PACK See Figure 2. • Lock switch trigger on your drill by placing the direction To turn your drill ON, depress the switch trigger. To turn it of rotation selector in center position. See Figure 5. OFF, release the switch trigger.
SWITCH LOCK KEYLESS CHUCK See Figure 5. See Figure 6. The switch trigger can be locked in the OFF position. This Your drill has a keyless chuck. As the name implies, you can feature can be used to prevent the possibility of accidental hand tighten or release drill bits in the chuck jaws.
INSTALLINGBITS REMOVING BITS SeeFigure7. See Figure 7. • Lock the switch trigger by placing the direction of • Lock the switch trigger by placing the direction of rotation selector in center position. See Figure 5. rotation selector in center position. See Figure 5. •...
BIT STORAGE DRILLING See Figure 10. See Figure 12. When not in use, bits provided with your drill can be LEVEL placed in the storage area located on the bottom of your drill as shown in Figure 10. SCREWDRIVER I ILr_ f=,...,...=...=.-= STORAGEAREA Fig.
CHUCK REMOVAL • Insert hex key in chuck and tighten chuck jaws se- curely. Tap sharply with a mallet in a counterclockwise See Figures 13, 14, and 15. direction. This will loosen chuck on the spindle. It can The chuck must be removed in order to use some now be unscrewed by hand.
Do not abuse power tools. Abusive practices can WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other damage toot as well as workpiece. part may create a hazard or cause product damage. Only the parts shown on parts list, page 17, are intended to be repaired or replaced by the customer.
CRAFTSMAN 3/8 in., 18 VOLT CORDLESS DRILL-DRIVER - MODEL NO. 315.114610 .=======, SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS PARTS LIST Part Number Description Quan. 6613401 Screw (Special) ..............6903330 Chuck ..................*Item No. 9 11378 Battery Pack (1323520) ............
Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters.