Craftsman 315.115410 Operator's Manual

1/2 in., 19.2 volt cordless drill-driver variable speed/reversible


Model No.
To reduce the risk of injury,
the user must read and understand the
operator's manual before using this
Help Line: 1-800-932-3188
Sears, Roebuck
and Co., 3333 Beverly
Rd., Hoffman
IL 60179 USA
Visit the Craftsman web page:
Save this manual for future
0( )us


Table of Contents

Summary of Contents for Craftsman 315.115410

  • Page 1 Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA 0( )us Visit the Craftsman web page: 983000-716 Save this manual for future reference 5-05...
  • Page 2 NEAREST SEARS STORE OR SEARS PARTS& REPAIR CENTER IN THE UNITED STATES, and Sears will repairit, free of charge. If this Craftsman tool is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.
  • Page 3 • Use safety equipment. Always wear eye protection. WARNING] Read all instructions. Failure to follow Safety equipment such as dust mask, non-skid safety all instructions listed below may result in electric shoes, hard hat, or hearing protection used for appro- shock, fire and/or serious injury.
  • Page 4 • Use the power tool, accessories and tool bits etc., make a connection from one terminal to another. in accordance with these instructions and in the Shorting the battery terminals together may cause burns or a fire. manner intended for the particular type of power tool, taking into account the working conditions •...
  • Page 5 WARNING! READ AND UNDERSTAND ALL • An extension cord should not be used unless absolutely necessary. Use of improper extension cord INSTRUCTIONS, Failure to follow all instructions could resultir_a risk of fire and electric shock. If listed below, may result in electric shock, fire extension cord must be used, make sure: and/or serious personal injury.
  • Page 6 Some ofthefollowing symbols maybeusedonthistool.Please study themandlearn theirmeaning. Proper interpretation ofthese symbols w illallow youtooperate t hetoolbetter a ndsafer. SYMBOL NAME DESIG NATIO N/EXP LANATION Volts Voltage Amperes Current Hertz Frequency (cycles per second) Watt Power Minutes Time Alternating Current Type of current ----=- Direct Current Type or a characteristic of current...
  • Page 7 The following s ignal words andmeanings areintended toexplain t helevels ofrisk associated withthis product. SYMBOL SIGNAL MEANING Indicates an imminently hazardous situation, which, if not avoided, will DANGER: result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, could WARNING: result in death or serious injury.
  • Page 8 PRODUCT SPECIFICATIONS Clutch ..............24 Position Chuck ............1/2 in. Keyless Motor ............... 19.2 Volt DC Torque..........Maximum 420 inJb. Switch ............Variable Speed Charger Input ........120 V, 60 Hz, AC only Gear Train ............... 2 Speed Charge Rate .............. 1 hour No Load Speed ........
  • Page 9 KNOW YOUR DRILL-DRIVER LED WORKLIGHT See Figure 1. The LED worklight,located on the front of the tool base, Beforeattempting to use this product, familiarize yourself illuminates when the switch trigger is depressed. This with all operating features and safety rules. provides extra light for increased visibility.
  • Page 10 CHARGING A COOL BATTERY PACK WARNING: Do not allow familiarity with tools to If battery pack is below normal temperature range, the make you careless. Remember that a careless green LED on charger wiMcome on. Allow battery pack to fraction of a second is sufficient to inflict serious reach normal temperature, then the red LED will come on.
  • Page 11 CHARGING A HOT BATTERY PACK TO INSTALL BATTERY PACK See Figure3. When using the tool continuously, the batteries in the battery pack will become hot. You should let a hot battery • Lock switch trigger on the drill by placing the direction pack cool down for approximately 30 minutes before of rotation selector in center position.
  • Page 12 To stop the drill, release the switch trigger and allow the WARNING: Battery tools are always in operating chuck to come to a complete stop. condition. Therefore, switch should always be locked NOTE: The drill will not run unless the direction of rotation when not in use or carrying at your side.
  • Page 13 KEYLESS CHUCK TODECREASE TORQUE See Figure 6. The drillhas a keylesschuck to tighten or release drill bits in the chuck jaws. The arrows on the chuck indicate ADJUSTINGRING which directionto rotate the chuck body in order to LOCK (tighten)or UNLOCK (release)the drill bit. WARNING: Do not hold chuck bodywith one hand and use power of the drillto tighten chuck jaws on drillbit.
  • Page 14 CHUCK BIT STORAGE UNLOCK COLLAR See Figure 9. DRILLBIT (RELEASE) When not in use, bits provided with the drill can be placed in the storage area located on the base of the drill. SCREWDRIVER BIT CHUCK JAWS LOCK (TIGHTEN) CHUCK STORAGE BODY AREA...
  • Page 15 ADJUSTING THE AUXILIARY HANDLE ASSEMBLY LEVEL See Figure 12. • Loosenthe auxiliaryhandle assembly by turningthe knobcounterclockwise. • Rotate the auxiliaryhandle assemblyto the desired location. • Tighten the auxiliaryhandle assemblysecurelyby turningthe knobclockwise. AUXILIARY TORQUE HANDLE ASSEMBLYADJUSTMENT RING Fig. 13 • When drilling hard, smoothsurfaces, use a center punch to mark the desired hole location.
  • Page 16 MALLET WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. CHUCK JAWS WARNING: Always wear safety goggles or safety glasses with side shields when usingcompressed air to clean tools. If the operationis dusty, also wear a dust mask.
  • Page 17 • Insert the hex key into the chuck and tighten the TO RETIGHTEN A LOOSE CHUCK chuck jaws securely. Tap sharply with a mallet in a The chuck may become loose on the spindle and develop counterclockwise direction. This will loosen the chuck a wobble.
  • Page 18 CRAFTSMAN 19.2 VOLT CORDLESS DRILL-DRIVER MODEL NO. 315.115410 (Item No. 11541) • The model number will be found on a plate attached to the motor housing. Always mention the model ] number in all correspondence regarding your CORDLESS DRILL-DRIVER or when ordering repair parts.
  • Page 19 Get it fixed, at your home or ours! Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories owner's manuals that you need to do-it-yourself.

Table of Contents