Sears Craftsman 944.527700 Owner's Manual
  1. Manuals
  2. Brands
  3. Sears Manuals
  4. Snow Blower
  5. Craftsman 944.527700
  6. Owner's manual
Sears Craftsman 944.527700 Owner's Manual

Sears Craftsman 944.527700 Owner's Manual

15.5 hp 30" 2-stage power=propelled snow thrower
Hide thumbs
Table of Contents

Advertisement

Quick Links

OWNER'S
MANUAL
MODEL NO.
944.527700
Caution:
Read and follow
all Safety Rules
and instructions
Before Operating
This Equipment
®
P
TWO-STAGE
R- ROPELLE
THROWER
• Assembly
• Operation
• Maintenance
• Service and Adjustments
• Repair Parts
Sears Canada, Inc., Toronto, Ontario
MSB 2B8

Advertisement

Table of Contents
loading

Related Manuals for Sears Craftsman 944.527700

Summary of Contents for Sears Craftsman 944.527700

  • Page 1 OWNER'S MANUAL MODEL NO. 944.527700 ® Caution: Read and follow TWO-STAGE all Safety Rules and instructions R- ROPELLE Before Operating THROWER This Equipment • Assembly • Operation • Maintenance • Service and Adjustments • Repair Parts Sears Canada, Inc., Toronto, Ontario MSB 2B8...
  • Page 2 iMPORTANT Safe Operation Practices for Walk=Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Snow throwers have ex= Look for this symbol to point out im- posed rotating parts, which can cause portant safety precautions,...

  • Page 3: Table Of Contents

    6. Whencleaning,repairingor inspecting the snow Clearing a Clogged Discharge Chute thrower, s topthe engineandmakecertainthe col- Hand contact with the rotating impeller inside the discharge lector/impeller andall movingpartshavestopped. chute is the most common cause of injury associated with Disconnect thespark plugwire andkeep thewireaway snow throwers.

  • Page 4: Product Specifications

    Warranty service is available by returning the Craftsman Snow Thrower to the nearest Sears Service Centre/Depart- ment in Canada. This warranty applies only while this product is in use in Canada.
  • Page 5 PARTS PACKED SEPARATELY I CARTON (1) MULTi= (1) FUEL STABiLiZER PACKET WRENCH (1) POWER CORD (2) SAFETY iGNiTiON KEYS (1) AUGER CONTROL 1111111 (1) TRACTION DRIVE CONTROL (1) DISCHARGE CHUTE EXTRA SHEAR DOLTS AND NUTS © (2) SHEAR BOLTS 1/4=20 x %3/4 (2) SPACERS (2) LOCKNUTS 1/4=20...
  • Page 6 RE-O ERATION Read these instructions and this manual in its entirety INSTALL SPEED CONTROL ROD (See Figs. 1 and 2) before you attempt to assemble or operate your new Remove plastic tie securing rod to lower handle. snow thrower. Reading the entire manual will familiar= insert rod into speed control bracket and secure with ize you with the unit, which will assist you in assembly, retainer spring.
  • Page 7 RE-O ERATION INSTALL TRACTION DRIVE CONTROL ROD INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) (See Figs. 3 and 4) The auger control rod has the short loop on the end of the spring as shown. The traction drive control rod has the long loop on the end of the spring as shown.
  • Page 8 BLY / RE-O ERATION iNSTALL CHUTE DEFLECTOR REMOTE CONTROL iNSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7) (See Figs. 8 and 9) Install remote cable bracket to discharge chute with NOTE: The multi-wrench provided in your parts bag may 5/16-18 carriage bolt and 5/16-18 Iocknut as shown, be used to install the chute rotater head, Tighten securely,...

  • Page 9: Operation

    OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUALAND ALL SAFETY RULES BEFORE OPERATING YOUR SNOWTHROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments, Save this manual for future reference, These symbols may appear on your snow thrower or in literature supplied with the product.
  • Page 10 O ERATION GASOLINE ELECTRIC AUGER DISCHARGE CHUTE CONTROL LEVER START BUTTON CONTROL LEVER DRIVE SPEED DEFLECTOR REMOTE RECOIL CONTROL LEVER CONTROL LEVER STARTER HANDLE ' TRACTION CHUTE DRIVE CHOKE DEFLECTOR CONTROL CON- LEVER TROL _HTURN TRIGGER SAFETY IGNITION LIGHT CHUTE ON / OFF SWITCH HANDLE...
  • Page 11 OPERATION The operation of any snow thrower can result TO CONTROL SNOW DISCHARGE (See Fig. 13) in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear WARNING: Snow throwers have ex- safety glasses or eye shields while operating posed rotating parts, which can cause your snow thrower or performing any adjust- ments or repairs.
  • Page 12 OPERATION Reverse ground speed will increase as the lever is pulled USING THE CLEAN-OUT TOOL (See Fig. 15) backward, allowing the operator to vary the speed of the in certain snow conditions, the discharge chute may be- unit while it is moving. come clogged with ice and snow.
  • Page 13 OPERATION • If snow thrower must be operated over gravel surface, BEFORE STARTING THE ENGINE use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position. CHECK ENGINE OiL LEVEL (See Fig. 21) Shut off engine and wait for all moving parts to stop. The engine on your snow thrower has been shipped, from the factory, already filled with oil.
  • Page 14 OPERATION TO START ENGINE WARM START- RECOIL STARTER Follow the steps above, keeping the choke in the "OFF" Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter position. DO NOT push the primer.

  • Page 15: Maintenance

    MAINTENANCE SCHEDULE J_£_,4"._0_ SERVICE AS YOU COMPLETE REGULAR SERVICE f_y_'_r_/'_'4r/_fb_ DATES Check for Loose Fasteners Clean / Inspect Snow Thrower Check/Replace V=Beks Lubrication Chart Check Engine Oil Level Change Engine Oil Inspect Muffler Check / Replace Spark Plug Empty Fuel Tank GENERAL RECOMMENDATIONS LUBRICATION...

  • Page 16: Service And Adjustments

    V-BELTS TO CHANGE ENGINE OIL Check V-belts for deterioration and wear after every 50 Determine temperature range anticipated before next oil hours of operation and replace if necessary. The belts change. All oil must meet API service classification SG-SL. are not adjustable. Replace belts if they begin to slip from •...
  • Page 17 SERVICE ADJUSTMENTS To replace the capscrew/shear bolts: WARNING: To avoid serious injury, before Disengage all controls and move throttle control to performing any service or adjustments: STOP position. Wait for all moving parts to stop. 1. Be sure the on/off switch is in the Remove safety ignition key and disconnect spark plug OFF position.

  • Page 18: Assembly / Pre-Operation

    SERVICE ADJUSTMENTS TO REPLACE BELTS (See Fig. 24) The auger and traction drive belts are not adjustable. If the HINT: Insert a 3/8" drive ratchet (in the "ON" position) into belts are damaged or begin to slip from wear, they should the square hole in idler arm and rotate ratchet clockwise be replaced.

  • Page 19: Storage

    TO REMOVE WHEELS (See Fig. 25) NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts • Remove the klik pin and remove wheel from axle. dealer. Tire sealant also prevents tire dry rot and corrosion, IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft - do not use the ENGINE...
  • Page 20 TROU OOTING See appropriate section in manuaJ unless directed to a Sears service centre/department. CAUSE CORRECTION PROBLEM Does not start Fuel shut-off valve (if so Turn fuel shut-off valve to OPEN position. equipped) in OFF position. Safety ignition key insert safety ignition key. is not inserted.
  • Page 21 CE NOTES...

  • Page 22: Repair Parts

    SNOW THROWER - - MODEL NUMBER REPAIR PARTS 944,527700 AUGER HOUSING / iMPELLER ASSEMBLY 6/_/13 ./"...
  • Page 23 REPAIR PARTS SNOW THROWER == MODEL NUMBER 944,527700 AUGER HOUSING / IMPELLER ASSEMBLY KEY PART KEY PART DESCRIPTION DESCRIPTION 191079 Pulley, Impeller 407768 O-Ring 188909 Bearing Assembly, Flange 407769 Bushing, Flange 3/4 155377 Nut, Hex Flange 5/16-18 174681 Washer, Thrust 180355 Bolt, Flat Head, Carriage 5/16-18x5/8 174684...
  • Page 24 REPAIR PARTS SNOW THROWER - - MODEL NUMBER 944,527700 CONTROL PANEL / DISCHARGE CHUTE...
  • Page 25 REPAIR PARTS SNOW THROWER == MODEL NUMBER 944,527700 CONTROL PANEL / DISCHARGE CHUTE PART DESCRIPTION 414280 Knob, Lever, Black 17501010 Screw #10-24 x 5/8 198475 Control Assembly, Deflector 73800600 Nut, Lock 3/8-16 19131316 Washer, Flat 3/8 404974 Control Assembly, Chute Rotater 405784X479 Support, Pivot 150078...
  • Page 26 REPAIR PARTS SNOW THROWER == MODEL NUMBER 944,527'700 HANDLES /" _-23 31 _ ..32...
  • Page 27 REPAIR PARTS SNOW THROWER - - MODEL NUMBER 944,527700 HANDLES PART DESCRiPTiON 405999X479 Lever, Auger Control, RH 405783X479 Lever, Traction Drive Control, LH 178888 Bushing, Flange 169675 Retainer, Hairpin 17060408 Screw, Hex Head 1/4-20 x 3/4 178652 Rod, Interlock 196333X008 Arm, Impeller Rod 196334X008 Arm, Traction Rod...
  • Page 28 REPAIR PARTS SNOW THROWER - - MODEL NUMBER 944,527700 DRIVE...
  • Page 29 REPAIR PARTS SNOW THROWER - - MODEL NUMBER 944,527700 DRIVE PART DESCRiPTiON 17490508 Screw 1/4-20 x 1/2 187794 Spacer, Axle 174697 Washer, Thrust 74780632 Screw, Cap, Hex Head 3/8-16 x 2 179830 Bearing, Axle 73930600 Nut, Hex, Centerlock 3/8-16 187776 Transmission Assembly 187787 Speed Control Arm, Hydro...
  • Page 30 SNOW THROWER - - MODEL NUMBER REPAIR PARTS 944,527700...
  • Page 31 REPAIR PARTS SNOW THROWER == MODEL NUMBER 944,527700 CHASSIS / ENGINE / PULLEYS PART DESCRIPTION 192873 Spring, Traction idler 180522 Pulley, idler (2-1/4) Engine, Briggs & Stratton, Model Number 21 P214-O942-E1 74780520 Screw, Hex Head 5/16-18 x 1-1/4 150078 Screw, Hex Washer Head 5/16-18 x 3/4 59289 Washer, Flat 166785...
  • Page 32 REPAIR PARTS SNOW THROWER - - MODEL NUMBER 944,527700 WHEELS "20...
  • Page 33 REPAIR PARTS SNOW THROWER - - MODEL NUMBER 944,527700 WHEELS PART DESCRIPTION 196752X417 Wheel Assembly, 16", with Power Steering, LH 155443 Pin, Klik 1/4 405161 Cover, Power Steering 184471 Screw, Shoulder, Hex Head #10-24 x 1/2 17060410 Screw, Hex Head 3/8-16 x 1 185603X479 Bracket, Steering Cable, RH 185602X004...
  • Page 34 SNOW THROWER - - MODEL NUMBER REPAIR PARTS 944,527700 DECALS PART DESCRIPTION 181037 Decal Danger 415449 Decal Craftsman, 13 HP/30" 181035 Decal Danger, Deflector 181042 Decal Danger 183876 Decal Craftsman 181033 Decal Instruction 415475 Decal Speed Control 183730 Decal Remote Deflector...
  • Page 35 BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 21P214=0942=E1 3O61 ',-q_842 1351 552_718 718A 1298 742 _ _329 REPLACEMENT ENGINE_ 48 SHORT BLOCK 358 ENGINE GASKET SET 1095 VALVE GASKET SET 51A_ 1022 363(_ ss3(_...
  • Page 36 BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 21P214o0942-E1 1171 o_4_ 383_ 45 _ 121 CARBURETOR OVERHAUL 127 © lO4 _ 163 % 105 [_ 51A( 633 @ 51Aq 977 CARBURETOR GASKET 105 [_ 51A( 633 @ 1127 ?
  • Page 37 BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 21P214o0942-E1 1251A 1288 1036 EMISSIONS LABEL 1011 597 _@ 684950 1252 _) 1251 1211 654;_ 697,_ 100_ 967_ 1119 1070 190'_...
  • Page 38 BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 21P214-0942-E1 663_ 163% 1227I ..505 @ 1230_} 209 j 1138 616_ 211S 773 _ 668A @ PART PART DESCRIPTION DESCRIPTmON 694874.+ (_:Gasket-lntake 794850 Cylinder Assembly 694875,+ O$Gasket-lntake 698340 Kit-Bushing/Seal (Magneto Side) 795017 Stud (Carburetor) 391086s •...
  • Page 39 BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 21P214=0942=E1 PART PART DESCRIPTION DESCRIPTION 698035 Lever-Control 697465 Cover-Starter Drive Hood-Snow 792008 Washer (Governor Control Lever) 793174 697268 Panel-Control 731A 794550 Hood-Snow 699629 Screw (Dipstick Tube) 699200 Screw (Starter Drive Cover) 794948 Muffler 691288 Gear-Timing 791478...
  • Page 40 Just Call: iiiiiiiiiiiiiiiiiii 1-800-4-1VlY-HOIVlE® iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiii (1-800-469-4663) iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiii 24 hours a day, 7 days a week iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiii For the repair of major brand appliances in your own home... iiiiiiiiiiiiiiiiiii no matter who made it, no matter who sold it! iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiii iiiiiiiiiiiiiiiiiii...

Table of Contents