Advertisement
b_
if whoa& are in correct alignmenh
the straight edge
wi!J contactthewheels at fourpoints, A, B,C and D.
c
if: any
misdignment
e×ists,
loosen
the set screw (57,
figure
5) in the _ower wheat
and,
with
the straight_
edge
contacting
points C and D oe the _awet whee!_
adiust it in: or out until the straightedge
contacts
points
A and
B of the _piper
whee!_
d.
if only one point
A or B is contacted,
odivst the se!f_
Iock_ng
blade
a$igement
screw (19)
to ti!t the upper
wheel
until
aS[ four
paints
are in coetoct,
e_
After
proper
allgnmeet
has been
accomplished,
tighten the set screw (571 to secure the iower wheat
on _hearbor shaft (60)_
NOTE: If a _/8-inch
w_dth blade
is used,
the alignment screw (19) will require 'further
3_ Guldes
Sow guide ossembUesare provided both above
and betow the table in order _o support the blade against
[Qtera! thrust end direct
thrust_ The _pper saw guide
assembly must operate
so the distance from the back
of the saw blade to the thrust roller remains the same
throughout the entire up and down movement of the
b_
C_
d_
if on adjustment is nee:essay, remove the, cover and
turn the upper saw guide bar adiusting _rew_ e_ther
in ar out as required
(See flgo_e 4_)When
adjus_
meet is completed !ock the adjusting
_rew
lack nut'
to maintain the adjusiment,
Adjust the sow guide assemblies so the latera! :saw
guides (whoa adjusted) wili coetact the Blade oe the
solid potion
only, not on the teeth or valleys behveen
teeth_ (See figure 20 This is accomplished
by loosen,.
ing the sew guide
assembly adiusfieg
screws and
moving the saw guide assemblies, forward
or' back-
ward
as required.
Whoa the adjustment
is correct,
Jack the saw guide assemblies in position
Set the lateral
saw guides us close as possible to
the blade
without binding
the blade
ot any point
or deflecting
it sidewise. Lock the set screws securing
the lateral saw guides when the adjustment is correct
The blade
thrust ro,!!ers shouid be set the thkkness
of a piece of newspaper from the back edge of the
e_
blade,(See figure 4.) Using a screwdriver, turn the
the bearing
hoJder in or' o_t until @e roller
is ie
correct position, The blade should to_ch these rollers
oe!y when cu_ing, not whee saw is ru_ning ffee_
The above odjustme_:ts should result i_ a free running
saw b!_de when no c_#ing
operofioes
are
being
g_
h_
The table
should
be square
with
the blade
and,
at
the some time,
the po#tter
should
indicate
:zero
on
the scaJe_ if a correctloe
is necessary,
it may be made
by piecing
an accurate
_uare
an the table
surface
and
against
the s_w
blade_
(See
figure
2_) Adjust
the 90 a stop
screw
untl]
the adjustment
is correct,
The te:bJe tilt poieter may now be reodiusted
to the
zero mark on thescale by loosening the screw which
hoids the pointer to the sow. (See figure 1_)
After comp!eting a!! adiustme_ts on the s_w, check:
tar'el:oily by turning the mechanism by hand several
revolutions before operating
the sow with power
NOT_:
After
a
few
hours
of operation,
tlghte_ aH pulley set screws.
OPERATION
, Co_tre_so
The operator
should
become
familiar
w_th aH
cont_o!s
before
operating
the: saw_ A _i_!e time spent
i:n
this effort
wilt
protect
the saw
and
insure
operational
sofe_
(See figures
2 and 4_)
a.
The t_b|e
'Jilt |ock
he,die
_ lacks the tobie
in any
position
with the saw blade
from
90 ° to 45°,
b_ The t_bie
tilt
p_inter
_ indicates
the table
angle
on
@e caiibrated
trunnion
_ale
c, The blade
g_ides
_ back up the blade
far
both
[otera!
and direct thrust,
d_ The b,l_e
g_ide
eieveti_
|ock k:_eb _ controls
the upper assembly in relation
to tobie surface for
various work piece thicknesses,
e. The blade
_[ig_e_
s_ew
_ provides _ means af
tihing the upper wheel for correct saw blade tracking
5
The blede tensie_
cam - (35, figure 5)
provides a
quick and easy meaes _or changing
saw b4ades, Pull
the cam handle down to re!ease the upper wheel and
loosen the saw biode_ Push the cam handte
up to
repo@ion the wheel and tighten the saw blade.
2_ Open,flag
Pr'e_ed_e,
a. Hold the work piece firmly against the table surface
during at! cutting operations.
b_ Do not farce the work against the blade beyond the
cu#ing capacity of the bJade_ as it will produce ex_
treme difiicul?
in folbwing
the pa_em
layout.
3_ 5efety
D_i_g
Operetie_,
CAU_|ON_
Always
disconnect
i_put
cable
from power supply when adjusting the sow,
from one working poslt_on to another
Advertisement
