Fujitsu PRIMERGY TX300 S6 Options Manual page 39

Main memory
F
III
Section
Figure 12: Extract from the configurator (EMEA market)
I
The current configurator can be found under:
http://ts.fujitsu.com/products/standard_servers/tower/primergy_tx300s6.html
(for the EMEA market)
http://primeserver.fujitsu.com/primergy/system.html
market)
TX300 S6
Memory
- There are 9 memory slots for max.
72GB (9x 8GB single / dual rank 1.5V RDIMM´s)
96GB (6x 16GB quad rank 1.5V RDIMMs)
12GB (6x 2GB UDIMMs)
=> max. 192GB for two CPU`s ( 96GB per CPU )
( For explanation of following terms refer to section "Memory Configurations"
- The memory area is divided into 3 channels per CPU with 3 slots per channel
- Slot 1 of each channel belongs to memory bank 1, the slot 2 belongs to memory bank 2 and
slot 3 belongs to memory bank 3
Systems with 3DPC (9 DIMMs / CPU) do not support mix of dual rank and quad rank modules
Registered and unbuffered memory modules can be selected
No mix of registered and unbuffered modules allowed.
DDR3 1066 and 1333MHz modules can be mixed, but run always with the slower speed.
With two DIMMs per channel, 1.5V DIMMs operate with 1333Mhz, 1.35V with 1066MHz as max., dep. on CPU
If 1.5V DIMMs and 1.35V (Low Voltage) DIMMs are mixed, DIMMs will run at 1.5V
SDDC (Chipkill) is supported only for registered memory modules.
1.) In the "Independent Channel Mode" is following configuration possible
- Each slot can optionally be equipped either with registered x4 organized DDR3 modules:
2GB single rank, 4GB and 8GB dual rank, 16GB quad rank
or with unbuffered x8 organized DDR3 modules: 2GB dual rank
2.) In the "Spare Channel Mode" is following configuration possible
- Each memory bank can optionally be equipped with 3x2GB single rank,
3x4GB and 3x8GB dual rank or 3x 16GB quad rank DDR3 modules.
Each slot of one bank has to be equipped with identical modules for spare channel mode
In channel A and B of CPU 1 or channel D and E of CPU 2 are always the active memory modules,
in channel C of CPU 1 and channel F of CPU 2 is always the spare module
No special order codes with UDIMMs are offered for this mode
3.) In the "Mirrored Channel Mode" is following configuration possible
- Each memory bank can optionally be equipped with 2x2GB single rank,
2x4GB and 2x8GB dual rank or 2x16GB quad rank DDR3 modules.
In each memory bank channel A and B of CPU 1 or channel D and E of CPU 2 have to be equipped with
identical modules for mirrored channel mode. Channel C of CPU 1 and channel F of CPU 2 is not equipped
In channel B is always the mirrored memory of channel A of CPU 1
In channel E is always the mirrored memory of channel D of CPU 2
No special order codes with UDIMMs are offered for this mode
- For each CPU minimum 1 memory module has to be configured in Independent Channel Mode
( => Additional memory extensions can still be configured up to eight times per CPU ) or
one bank has to be equipped with two modules (channel A+B for CPU 1 or D+E for CPU 2) in
Mirrored Channel Mode
( => Additional memory extensions can still be configured up to two times per CPU ) or
one bank has to be equipped with three modules (channel A+B+C for CPU 1 or D+E+F for CPU 2)
in Spare Channel Mode or Performance Mode
( => Additional memory extensions can still be configured up to two times per CPU )
Options Guide
Memory modules
System configurator and order-information guide
PRIMERGY TX300 S6 Status 2010-01-27
(for the Japanese
39