Page 1
EN-5100e EN-5100e 15 inch TFT LCD Monitor User’s Manual by Envision Peripherals, Inc. www.ENVISIONmonitor.com Before operating your monitor, please read this manual thoroughly. EN-5100e 31MY02...
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. EN-5100e For Your Safety Notice 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Page 3
EN-5100e For Your Safety • The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin.
EPI service center for replacement when the screen is dark, flickering or not lighting up. Never attempt to replace it by yourself. EN-5100e For Your Safety General Notes • Do not install the monitor near heat sources such as radiators or air ducts.
• Ergonomic Design • Space Saving, Compact Case Design EN-5100e Package Contents The box that your monitor was shipped in should have included the following items: 1. EN-5100e LCD Monitor 2. Power Cord 3. Windows 95/98/2000/ME INF Driver Disk EN-5100e 31MY02...
Page 6
3. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip. EN-5100e Caution: Make sure the power cord is the correct type that is required in your area. This LCD...
CEE-22 terminated connectors (see illustration above). EN-5100e Follow these steps: 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws.
• Hold the stand firmly when you change the monitor's angle. • You can adjust the monitor's angle from -5° to 45°. EN-5100e • Do not touch the LCD screen when you change the angle. It may cause damage or breakage.
MENU: Press this button to open the OSD window or exit from the OSD window. EN-5100e Operating Instructions Power Indicator: A green light indicates that the monitor is on. An orange light indicates that the monitor is in Off mode.
3. Press MENU to open the function’s window. 4. Press the < or > buttons to change the settings of the function. EN-5100e Operating Instructions 5. To save and exit, highlight the EXIT icon and press MENU or leave the monitor alone for 10 seconds.
EDID information. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B. EN-5100e Operating Instructions How to Install INF & ICM File 1. Insert the Windows 95/98/2000/ME/XP INF Driver Disk into your floppy drive.
• Inspect the video cable and make sure that none of the pins are bent. primary colors (RED, • Make sure the video cable is properly connected to the computer. GREEN, or BLUE) EN-5100e Technical Support (FAQ) Possible Solution EN-5100e...
Page 13
• Make sure the video cable is properly connected to the computer. If the connector is loose, tighten the connector's two screws. • Inspect the video cable and make sure that none of the pins are bent. EN-5100e Technical Support (FAQ) Possible Solution...
640 x 480 640 x 400 640 x 350 720 x 400 640 x 480 640 x 480 640 x 480 800 x 600 EN-5100e Technical Support (FAQ) Possible Solution Vertical Frequency 60 Hz 800 x 600 70 Hz 800 x 600...
Response time Video Separate Sync. H-Frequency V-Frequency Display Colors Dot Clock Maximum Resolution EN-5100e Appendix Plug & Play TFT Color LCD Input Connector 15.0" (38.1 cm) Input Video Signal 0.01” (0.3 mm) (H) 0.01” (0.3 mm) (V) Maximum Screen Size 100°...
Page 16
H-Position V-Position Auto-Center 6500° K 7800° K RGB Color temp. Reset Exit EPA ENERGY STAR® Power Consumption 25 Watts (Maximum) Regulatory UL, CSA, FCC, Compliance TÜV/GS, CE EN-5100e Appendix Optimal Viewing Mode: 1024 x 768 x 75 Hz EN-5100e 31MY02...