Subscribe to Our Youtube Channel
Related Manuals for Envision EN-7100s
Summary of Contents for Envision EN-7100s
- Page 1 EN-7100s EN-7100s 17 inch TFT LCD Monitor User’s Manual by Envision Peripherals, Inc. www.ENVISIONmonitor.com Before operating your monitor, please read this manual thoroughly. AOC LM720 v1_090802...
-
Page 2: Fcc Statement
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. EN-7100s For Your Safety Notice 1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. - Page 3 Overloading can result in fire or electric shock. • For use only with power adapter (Output 12Vdc) which has UL, CSA listed license. EN-7100s Precautions • The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin.
-
Page 4: Special Notes On Lcd Monitors
EPI service center for replacement when the screen is dark, flickering or not lighting up. Never attempt to replace it by yourself. EN-7100s For Your Safety General Notes • Do not install the monitor near heat sources such as radiators or air ducts. -
Page 5: Before You Operate The Monitor
• Space Saving, Compact Case Design EN-7100s Package Contents The box that your monitor was shipped in should have included the following items: 1. EN-7100s LCD Monitor 2. Power Adapter 3. Power Cord 4. Windows 95/98/2000/ME/XP INF Driver Disk 5. Quick Start Guide 6. - Page 6 4. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip. EN-7100s Caution: Make sure the power cord is the correct type that is required in your area. This LCD monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required).
- Page 7 Before You Operate the Monitor EN-7100s Preparing to Install An Optional Wall Mounting Arm (Not supplied) This monitor can be attached to a wall mounting See next page for further installation instructions. arm you purchase separately. Disconnect power before this procedure. Follow these steps: 1.
-
Page 8: Install An Optional Wall Mounting Arm (Not Supplied)
3. Insert the power cable into the slot on the back of the monitor. EN-7100s The Envisionl EN-7100s is compatible with the Ergotron line of mounting and arm solutions. Contact Ergotron at 800-888-8458 or visit their web site at www.ergotron.com for more information on the many ways on which you can mount your Envision LCD monitor. -
Page 9: Adjusting The Viewing Angle
It may cause damage or breakage. • Be careful to avoid pinching your hand in the swivel base. EN-7100s How to Install INF & ICM File 1. Insert the Windows 95/98/2000/ME/XP INF Driver Disk into your floppy drive. -
Page 10: Front Panel Buttons
MENU: Press this button to open the OSD window or exit from the OSD window. EN-7100s Operating Instructions Power Indicator: A green light indicates that the monitor is on. An orange light indicates that the monitor is in Off mode. -
Page 11: Adjusting The Osd Settings
3. Press MENU to open the function’s window. 4. Press the < or > buttons to change the settings of the function. EN-7100s Operating Instructions 5. To save and exit, highlight the EXIT icon and press MENU or leave the monitor alone for 10 seconds. -
Page 12: How To Optimize The Dos-Mode
2 seconds. The screen will be automatically adjusted. If the screen is distorted (for example: the picture can't go to full screen, the background of white EN-7100s Operating Instructions pattern has vertical stripe noise, or the characters are twisted): 1. -
Page 13: Technical Support (Faq)
4 Dark Sub-pixels or combination of 6 Dark & Bright. The panel used on this product has a total of 3,932,160 sub-pixels. So even the maximum allowed of 6 bad sub-pixels would only amount to a very small 0.00015% of the total sub-pixels EN-7100s Possible Solution EN-7100s v1_090802... - Page 14 • Make sure the video cable is properly connected to the computer. If the connector is loose, tighten the connector's two screws. • Inspect the video cable and make sure that none of the pins are bent. EN-7100s Technical Support (FAQ) Possible Solution...
-
Page 15: Resolution Chart
640 x 400 640 x 350 720 x 400 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 EN-7100s Technical Support (FAQ) Possible Solution Vertical Frequency 60 Hz 70 Hz 70 Hz 70 Hz 72.8 Hz... -
Page 16: Specifications
Response time Video Separate Sync. H-Frequency V-Frequency Display Colors Dot Clock Maximum Resolution EN-7100s Appendix Plug & Play TFT Color LCD Input Connector 17" (43.2 cm) Diagonal Input Video Signal 0.264 mm (H) x 0.264 mm (V) Maximum Screen Size 150°... - Page 17 Focus Clock H-Position V-Position Auto-Center Language Dos-mode Resolution Selected 6500° K 7800° K RGB Color temp. Recall Exit EPA ENERGY STAR® Power Consumption 45 Watts (Maximum) Regulatory UL, CSA, FCC, TÜV/ Compliance GS, CE, XP Logo EN-7100s Appendix EN-7100s v1_090802...
-
Page 18: Factory Preset Timing Table
800 × 600 832 × 624 1024 × 768 1024 × 768 1024 × 768 1024 × 768 SXGA 1280 x 1024 1280 x 1024 EN-7100s Appendix Resolution Horizontal (in pixels) Frequency 31.47 kHz 31.47 kHz 31.47 kHz 35.00 kHz 37.50 kHz... -
Page 19: Connector Pin Assignment
Connector Pin Assignment Pin Number EN-7100s Appendix Description Pin Number Green Blue Ground Ground R-Ground G-Ground B-Ground EN-7100s Description Detect Cable DDC-Serial Data H-Sync V-Sync DDC-Serial Clock v1_090802...
Need help?
Do you have a question about the EN-7100s and is the answer not in the manual?
Questions and answers