Lenovo ThinkServer RD630 Hardware Maintenance Manual
  1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. Server
  5. ThinkServer RD630
  6. Hardware maintenance manual
Lenovo ThinkServer RD630 Hardware Maintenance Manual

Lenovo ThinkServer RD630 Hardware Maintenance Manual

Machine types: 2577, 2579, 2592, 2593, 2594, and 2595
Hide thumbs Also See for ThinkServer RD630:
Table of Contents

Advertisement

Quick Links

See also: Software User Manual , User Manual
ThinkServer
Hardware Maintenance Manual
Machine Types: 2577, 2579, 2592, 2593, 2594, and 2595

Advertisement

Table of Contents
loading

Related Manuals for Lenovo ThinkServer RD630

Summary of Contents for Lenovo ThinkServer RD630

  • Page 1 ThinkServer Hardware Maintenance Manual Machine Types: 2577, 2579, 2592, 2593, 2594, and 2595...
  • Page 2 • Appendix A “Notices” on page 177 First Edition (May 2012) © Copyright Lenovo 2012. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.

  • Page 3: Table Of Contents

    Remote management software ..Configuring RAID using the ThinkServer Lenovo Rack Planner ..EasyStartup program ..ThinkServer Smart Grid Technology ..
  • Page 4 Installing or replacing the optical drive . . . Lenovo Support Web site..Installing or replacing a hot-swap hard disk Help and service ....

  • Page 5: Safety Information

    제품을 사용하기 전에 제품과 함께 제공되는 문서 DVD의 다국어 안전 지침을 주의 깊게 읽어보십시오. Voordat u het product gebruikt, moet u ervoor zorgen dat u de meertalige veiligheidsinstructies op de documentatie-dvd van het product hebt gelezen en begrijpt. © Copyright Lenovo 2012...
  • Page 6 Przed skorzystaniem z produktu należy zapoznać się z wielojęzycznymi instrukcjami bezpieczeństwa znajdującymi się na płycie DVD z dokumentacją dostarczoną wraz z produktem. Antes de utilizar o produto, leia atentamente as instruções de segurança multilingues que constam no DVD de documentação fornecido com o produto. Înainte de a utiliza produsul, asiguraţi-vă...
  • Page 7 The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: • Throw or immerse into water • Heat to more than 100°C (212°F) • Repair or disassemble Dispose of the battery as required by local ordinances or regulations. © Copyright Lenovo 2012...
  • Page 8 Statement 3 CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. •...
  • Page 9 Statement 9 CAUTION: Disconnect the hot-swap fan cables before removing the fan from the device to protect against personal injury. Statement 10 CAUTION: The following label indicates a sharp-edge hazard. © Copyright Lenovo 2012...
  • Page 10 Statement 11 CAUTION: The following label indicates a potential heat hazard. Statement 12 DANGER Overloading a branch circuit is a potential fire hazard and a shock hazard under certain conditions. To avoid these hazards, ensure that your system electrical requirements do not exceed branch current ratings at the installation site.
  • Page 11 This product contains a Class 1M laser. Do not view directly with optical instruments. Statement 18 CAUTION: Do not place any object on top of rack-mounted products. Statement 19 CAUTION: Hazardous moving parts. Keep fingers and other body parts away. © Copyright Lenovo 2012...

  • Page 12: Safety Inspection Guide

    Statement 20 CAUTION: A lithium ion battery is provided. To avoid possible explosion, do not burn the battery. Replace the battery only with the Lenovo-approved part. Recycle or discard the battery as instructed by local regulations. Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury.

  • Page 13: Grounding Requirements

    Grounding requirements Electrical grounding of the server is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician. © Copyright Lenovo 2012...
  • Page 14 ThinkServer Hardware Maintenance Manual...

  • Page 15: Chapter 1. General Information

    • For the most up-to-date information about your server, go to: http://www.lenovo.com/thinkserver • Lenovo maintains pages on the World Wide Web, where you can get the latest technical information and download documentation or device drivers and updates. To access the Lenovo Support Web site, go to: http://www.lenovo.com/support...
  • Page 16 DVD. Note: Lenovo maintains pages on the World Wide Web, where you can get the latest technical information and download documentation or device drivers and updates. Some information in the documents on the documentation DVD might change without notice after the first release of the DVD.
  • Page 17 This document provides information about component locations, replacement procedures for major Field Replaceable Units (FRUs), and troubleshooting and diagnostics. This document is updated frequently, and the most up-to-date version is always available in English on the Lenovo Web site at: http://www.lenovo.com/ThinkServerUserGuides...
  • Page 18 ThinkServer Hardware Maintenance Manual...

  • Page 19: Chapter 2. Server Setup Road Map

    ThinkServer EasyStartup program. 10. Check for firmware updates. See “Updating the firmware” on page 69. 11. Install management applications and any other applications. Refer to the documentation that comes with the applications that you want to install. © Copyright Lenovo 2012...
  • Page 20 ThinkServer Hardware Maintenance Manual...

  • Page 21: Chapter 3. Product Overview

    DVD, and software media. Note: Depending on the model, your server might look slightly different from the following illustration. Figure 1. Server package Server Material box, including power cord(s), printed documentation, a documentation DVD, and software media Rail kit © Copyright Lenovo 2012...

  • Page 22: Features

    (internal cache size varies by model) For a list of the ThinkServer microprocessor options, go to: http://www.lenovo.com/thinkserver Memory Your server has 20 memory slots. For more information, see “Memory module installation rules” on page 82.
  • Page 23 Input/Output (I/O) features • One serial connector on the rear panel • Six USB 2.0 connectors (two on the front panel and four on the rear panel) • Three RJ-45 Ethernet connectors on the rear panel (Ethernet connector 0 is for system management) •...
  • Page 24 ThinkServer Management Module Premium (TMM Premium), which also is known as integrated keyboard, video, and mouse (iKVM) key. The TMM Premium is a remote management module. You can purchase a TMM Premium from Lenovo and install it on the TMM Premium connector (also known ThinkServer Hardware Maintenance Manual...
  • Page 25 Meanwhile, it is easily accessible by remote KVM and controllable through LAN or Internet. For more information, refer to the ThinkServer Management Module User Guide, which is available for download http://www.lenovo.com/ThinkServerUserGuides – Media redirection The embedded Web server provides a Java JNLP to enable the remote media redirection. This is used in conjunction with the remote KVM feature or as a standalone applet.

  • Page 26: Specifications

    Specifications This topic lists the physical specifications for your server. Dimensions Width without rack handles: 442 mm (17.4 inches) Width with rack handles: 482.4 mm (19 inches) Depth without rack handles: 720.6 mm (28.37 inches) Depth with rack handles: 734 mm (28.9 inches) Height: 87.6 mm (3.45 inches) Weight The product weight varies depending on different system configurations.

  • Page 27: Thinkserver Easyupdate Firmware Updater

    The BIOS and TMM (also known as BMC) firmware keeps updating after the shipment of the server. Lenovo maintains pages on the Support Web site and provides the BIOS and TMM update utilities with instructions for download to help you update the BIOS and TMM firmware if needed. For more information, see “Updating or recovering the BIOS”...

  • Page 28: Thinkserver Smart Grid Technology

    Intel Intelligent Power Node Manager technology. Lenovo provides a trial version of the ThinkServer Smart Grid Technology program with a free 90-day subscription. After 90 days, you must renew the license to continue using the program. You can purchase the license from Lenovo to activate the ThinkServer Smart Grid Technology program and expand the management capability of the program when the free trial ends.
  • Page 29 The machine type, model, and serial number label is attached on the pull-out information card, which is a small plastic tab and can be slid out of the front of the chassis. The following illustrations are samples of the machine type, model, and serial number labels on server models with different hard disk drive configurations. Note: Depending on the model, your server might look slightly different from the illustrations in this topic.

  • Page 30: Front View Of The Server

    Front view of the server This topic provides information to help you locate the parts on the front of the server. The front view of the server varies by model. The illustrations in this topic show the server front views based on the supported hard disk drives: •...
  • Page 31 3.5-inch hard disk drive area The EMI integrity and cooling of the server are protected by having all drive bays covered or occupied. The number of the installed hard disk drives in your server varies by model. The vacant hard disk drive bays are occupied by dummy hard disk drive trays.
  • Page 32 Front view of server models with 2.5-inch hard disk drives The following illustration shows the front view of server models with 2.5-inch hard disk drives. Figure 6. Front view of server models with 2.5-inch hard disk drives 2.5-inch hard disk drive area (right cage) Rack handle (left) 2.5-inch hard disk drive area (middle cage) Diagnostic panel (varies by model)

  • Page 33: Front Panel

    Slim optical drive Some server models come with a slim SATA optical drive (DVD-RW or DVD-ROM). Rack handle (left) Rack handle (right) If your server is installed in a rack cabinet, you can use the rack handles to help you slide the server out of the rack cabinet;...
  • Page 34 Power status LED Color Description The server is on. Green None The server is off. Blinking Green The server is in ACPI S1 mode, which also is known as Power On Suspend (POS) mode. In this mode, the microprocessor(s) are not working while other hardware devices are still working.

  • Page 35: Diagnostic Module

    Diagnostic module This topic provides information about the diagnostic module and the diagnostic LEDs on the panel of the module. To locate the diagnostic panel, see “Front view of the server” on page 16. Your server comes with one of the following diagnostic modules: •...
  • Page 36 Memory module status LED When the memory module status LED is lit in amber, it indicates that one or more memory modules are overheated. Microprocessor status LED (also known as CPU status LED) When the microprocessor status LED is lit in amber, it indicates that one or two microprocessors are overheated.
  • Page 37 System fan error LEDs When a system fan error LED is lit in amber, it indicates that the corresponding system fan is operating slowly or has failed. The following illustration shows the system fans and their numbers. Note: Depending on the model, your server might look slightly different from the illustration. Figure 11.
  • Page 38 CPU1 DIMM status LEDs CPU2 DIMM status LEDs When a DIMM status LED is lit in amber, it indicates that the corresponding memory module is overheated. The following illustration shows the memory modules and their numbers. Figure 12. DIMM status LEDs and DIMMs Ambient temperature limit LED When this LED is lit in amber, it indicates that the ambient temperature is below 7°C (44.6°F) or over 40°C (104°F), which is not proper for server operation.

  • Page 39: Rear View Of The Server

    You can purchase a hot-swap redundant power supply option from Lenovo and install the power supply to provide power redundancy without turning off the server. On each hot-swap redundant power supply, there is a status LED near the power cord connector. When the LED is lit in green, it indicates that the hot-swap redundant power supply is working correctly.
  • Page 40 PCI Express card area for cards on the riser card assembly 2 There are three PCI Express card slots on the riser card assembly 2 for installing Ethernet cards or other supported PCI Express cards. Figure 14. Riser card assembly 2 Note: The slot and slot are supported only in server models with two microprocessors.
  • Page 41 PCI Express card area for cards on the riser card assembly 1 There are two PCI Express card slots on the riser card assembly 1. Figure 15. Riser card assembly 1 Notes: • For a RAID card, it must be installed into the upper slot (callout ) on the riser card assembly 1.
  • Page 42 5 8 9 Ethernet connectors (RJ-45) Used to attach an Ethernet cable for a LAN. Each Ethernet connector has two status LEDs to help you identify the Ethernet connectivity, activity, and connection speed. Notes: • The Ethernet connector 0 (callout ) marked with “MGMT”...

  • Page 43: Server Components

    ID LED When you press the ID button on the front panel, the ID LEDs on both the front and rear of the server are lit to help you locate the server among other servers. You also can turn on the ID LEDs using a remote management program for server presence detection.
  • Page 44 Components of server models with 3.5-inch hot-swap hard disk drives Figure 17. Components of server models with 3.5-inch hot-swap hard disk drives Cooling shroud Pull-out information card Power supply cooling shroud Rack handle (left) Riser card assembly 2 Front panel board One or two hot-swap redundant power supplies Backplane for 3.5-inch hard disk drives PCI Express card(s) (available in some models)
  • Page 45 Components of server models with 2.5-inch hot-swap hard disk drives Figure 18. Components of server models with 2.5-inch hot-swap hard disk drives Cooling shroud Slim optical drive (available in some models) Power supply cooling shroud Diagnostic module (varies by model) Riser card assembly 2 Rack handle (left) Front panel board...
  • Page 46 FRU information, such as FRU part numbers and supported server models, go to: http:/www.lenovo.com/serviceparts-lookup Notes: • Before servicing a Lenovo product, ensure that you read and understand the “Safety information” on page iii. • Use only parts provided by Lenovo.

  • Page 47: Hot-Swap Hard Disk Drive Status Leds

    Hot-swap hard disk drive status LEDs Each hot-swap hard disk drive has two status LEDs on the front. Figure 19. 3.5-inch hot-swap hard disk drive status LEDs Figure 20. 2.5-inch hot-swap hard disk drive status LEDs Hard disk drive activity LED Hard disk drive RAID status LED Description The hard disk drive has failed or is...

  • Page 48: Raid Card

    1. Your server comes with a RAID card to provide advanced SATA/SAS hardware RAID functions. You also can purchase a supported RAID card from Lenovo and install it into the server. See “Replacing the RAID card” on page 141.

  • Page 49: Expander Card

    ThinkServer RAID 700 Adapter (also known as ThinkServer 9260-8i SAS RAID Adapter) The following illustration shows the connectors on the ThinkServer RAID 700 Adapter. Figure 22. ThinkServer RAID 700 Adapter Ports 7-4 Board-to-board connector Ports 3-0 Ports 7-4 Used to connect a mini-SAS signal cable. See “Mini-SAS to mini-SAS signal cable connections” on page 39. Ports 3-0 Used to connect a mini-SAS signal cable.

  • Page 50: Hot-Swap Hard Disk Drive Backplane

    The following illustration shows the connectors on the expander card. Each connector on the expander card is used to connect a mini-SAS to mini-SAS signal cable. For detailed information, see “Mini-SAS to mini-SAS signal cable connections” on page 39. Figure 23. Expander card Connector 1 Connector 4 Connector 2...
  • Page 51 The following illustrations show the connectors on the backplane for 3.5-inch hard disk drives. Figure 24. Front view of the backplane for 3.5-inch hard disk drives Slot 0 for a 3.5-inch hard disk drive Slot 7 for a 3.5-inch hard disk drive Slot 2 for a 3.5-inch hard disk drive Slot 5 for a 3.5-inch hard disk drive Slot 4 for a 3.5-inch hard disk drive...
  • Page 52 Backplane for 2.5-inch hard disk drives This topic provides information to help you locate the connectors on the backplane for 2.5-inch hard disk drives. The following illustrations show the connectors on the backplane for 2.5-inch hard disk drives. Figure 26. Front view of the backplane for 2.5-inch hard disk drives Slot 0 for a 2.5-inch hard disk drive or solid-state Slot 4 for a 2.5-inch hard disk drive or solid-state drive drive...

  • Page 53: Mini-Sas To Mini-Sas Signal Cable Connections

    8-pin power connector Used to connect a power cable to provide power to the backplane. Mini-SAS ports 4-7 Used to connect the mini-SAS connector on one end of a mini-SAS to mini-SAS signal cable to support the hard disk drive 4 to hard disk drive 7; or to support the hard disk drive 12 to hard disk drive 15 if the backplane is for hard disk drives in the right cage of the server.
  • Page 54 Use the following instructions to connect cables from the RAID card to the backplane: 1. For hard disk drive 0 to hard disk drive 3, do one of the following depending on the type of your RAID card: • If you are using a ThinkServer RAID 500 Adapter, use a mini-SAS to mini-SAS signal cable and connect the mini-SAS connector on one end of the cable to the port 0 on the ThinkServer RAID 500 Adapter.
  • Page 55 • If you are using a ThinkServer RAID 500 Adapter, do the following: 1. Use a mini-SAS to mini-SAS signal cable and connect the mini-SAS connector on one end of the cable to the port 0 on the ThinkServer RAID 500 Adapter. Then, connect the mini-SAS connector on the other end of the cable to the connector 1 on the expander card.

  • Page 56: System Board Components

    Use the following instructions to connect cables from the expander card to the backplanes for 2.5-inch hard disk drives: 1. For hard disk drive 0 to hard disk drive 3, use a mini-SAS to mini-SAS signal cable and connect the mini-SAS connector on one end of the cable to the connector 3 on the expander card.
  • Page 57 Figure 30. System board components Front panel connector Redundant power supply connector 2 Backplane power connector 1 Internal USB connector 1 Internal USB connector 2 Backplane power connector 2 Diagnostic module connector Memory slots (4) Front VGA connector System fan 6 connector Microprocessor socket 2 SATA connector 0 Platform Controller Hub (PCH)
  • Page 58 Front panel connector Used to connect the front panel cable. Internal USB connector 1 Used to connect the front panel USB cable. Internal USB connector 2 Reserved for the manufacturer. Diagnostic module connector Used to connect the cable of the diagnostic module. Front VGA connector Used to connect the cable of the VGA DB-15 connector on the front panel of the server.

  • Page 59: System Board Jumpers And Switches

    ThinkServer Management Module With the integrated ThinkServer Management Module (also known as the BMC chip), no matter what condition the server operating system is in and no matter if the server is on or off, as long as the server is connected to network and an ac power source, the interaction with the TMM controlled servers can be achieved through system network.
  • Page 60 and to avoid any possible damage to a live circuit. Jumper pins arranged in groups on the system board are called jumper blocks. When two or more jumper pins are capped with a jumper, an electrical connection is made between them and the equipment is thus instructed to activate certain settings accordingly. The following illustration shows a jumper in the default setting position (pin 1 and pin 2).
  • Page 61 The following illustration shows the status of the jumpers and switches on the system board of your server. You can configure, recover, enable, or disable some specific features of the system board by setting the jumpers and switches. Figure 32. System board jumpers and switches Clear CMOS (Complementary Metal Oxide Semiconductor) jumper TMM Enable/Disable jumper (also known as BMC Enable/Disable jumper) System board switches...
  • Page 62 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface.
  • Page 63 System board switches There are four switches on the system board of your server. Figure 33. System board switches BIOS recovery switch Management Engine (ME) in force update switch Reserved for the manufacturer Clear password switch BIOS recovery switch Used to recover the BIOS if the power to your server is interrupted while the BIOS is being updated and your server cannot start correctly.

  • Page 64: System Board Leds

    1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface.
  • Page 65 To solve the problem, you might need to reinstall or replace the system fan. See “Replacing a system fan” on page 150. If it is a system board problem, contact the Lenovo Customer Support Center.
  • Page 66 ThinkServer Hardware Maintenance Manual...

  • Page 67: Chapter 4. Turning On And Turning Off The Server

    • When you turn off the server and leave it connected to an ac power source, the server also can respond to a remote request to turn on the server. To remove all power from the server, you must disconnect the server from the ac power source. © Copyright Lenovo 2012...
  • Page 68 • For information about your specific operating system, refer to the related documentation or help system for the operating system. ThinkServer Hardware Maintenance Manual...

  • Page 69: Chapter 5. Configuring The Server

    – Select Memory Configuration and follow the instructions on the screen to view information about the installed memory modules. – Select SATA/SAS Configuration and follow the instructions on the screen to view information about the installed SATA or SAS devices, such as a hard disk drive or an optical drive. © Copyright Lenovo 2012...

  • Page 70: Setup Utility Program Interface

    “Save & Exit menu” on page 58 Lenovo provides the BIOS update utility on the Lenovo Support Web site. You can download the BIOS update utility to update the BIOS if the newer BIOS version specifically solves a problem you have. See “Updating or recovering the BIOS”...
  • Page 71 Notes: • Enabled means that the function is configured. • Disabled means that the function is not configured. The Advanced menu contains the following submenus. For more information, enter the corresponding submenu and refer to the instructions on the screen. •...

  • Page 72: Setting The System Date And Time

    • System Information: View basic information about your server. • BMC Network Configuration: Set BMC configuration parameters. Boot Options menu The Boot Options menu in the Setup Utility program provides an interface to help you view or change the server startup options, including the startup sequence and boot priority for various devices. Changes in the startup options take effect when the server starts.

  • Page 73: Using Passwords

    Using passwords By using the Setup Utility program, you can set a password to prevent unauthorized access to your server. You do not have to set a password to use your server. However, using a password improves computing security. If you decide to set a password, read the following topics. Setup Utility program password types The following types of passwords are available in the Setup Utility program: •...

  • Page 74: Selecting A Startup Device

    TPM function is only available when there is a TPM installed in your server. See “Installing the TPM” on page 106. You can purchase a TPM from Lenovo. After installing a TPM, you need to check if the TPM function is enabled in the Setup Utility program.

  • Page 75: Setting The Mode Of The Ethernet Connector 0

    Setup Utility program” on page 55. The TMM firmware provides remote management features. Lenovo might make changes and enhancements to the BIOS and TMM firmware. When updates are released, they are available for download on the Lenovo Web site at http://www.lenovo.com/drivers. You can update the server firmware by downloading an update package and following the instructions on the Web page.

  • Page 76: Recovering From A Bios Update Failure

    BIOS for an easier reconfiguration in the new BIOS version. To update (flash) the BIOS, do the following: 1. Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to locate the BIOS update package. 2. Download the BIOS update package and the installation instructions in a TXT file.

  • Page 77: Using The Thinkserver Easystartup Program

    (bootable) ThinkServer EasyStartup DVD. The user guide for the program also is on the DVD and can be accessed directly from the program interface. If you do not have a ThinkServer EasyStartup DVD, you also can download an ISO image from the Lenovo Support Web site and make a disc by yourself.

  • Page 78: Starting The Thinkserver Easystartup Program

    • Ability to install the operating system and device drivers in an unattended mode to save time • Ability to create a reuseable response file that can be used with similarly configured Lenovo servers to make future installations even faster Starting the ThinkServer EasyStartup program This topic provides instructions on how to start the ThinkServer EasyStartup program.

  • Page 79: Using The Thinkserver Easystartup Program On A Windows Operating System

    DVD into an internal or external optical drive. The DVD starts automatically in most environments. If the DVD fails to start, open the launch.exe file located in the root directory of the DVD. Notes: • You should read and accept the Lenovo License Agreement when prompted. ® • On the Microsoft Windows Server...

  • Page 80: Configuring Raid

    ThinkServer EasyStartup DVD. Note: The most up-to-date device drivers for various server models are always available for download on the Lenovo Support Web site at: http://www.lenovo.com/drivers Configuring RAID This topic provides information about RAID and the utility programs that are available for you to configure RAID.
  • Page 81 • RAID 0: block-level striping without parity or mirroring Simple stripe sets are normally referred to as RAID 0. RAID 0 uses striping to provide high data throughput, especially for large files in an environment that does not require fault tolerance. RAID 0 has no redundancy and it provides improved performance and additional storage without fault tolerance.

  • Page 82: Configuring Raid Using The Thinkserver Easystartup Program

    For instructions on how to configure and manage the advanced SATA or SAS hardware RAID, refer to the MegaRAID SAS Software User Guide on the documentation DVD that comes with your server. This document also is available on the Lenovo Web site at: http://www.lenovo.com/ThinkServerUserGuides...

  • Page 83: Configuring The Ethernet Controllers

    Updating the firmware The firmware in the server is periodically updated and is available for download on the Lenovo Web site. Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to check for the latest level of firmware, such as the BIOS updates and device drivers.
  • Page 84 For detailed information about using the Lenovo ThinkServer EasyManage program, refer to the help system for the program. ThinkServer Hardware Maintenance Manual...

  • Page 85: Chapter 6. Installing, Removing, Or Replacing Hardware

    • Before using the product, ensure that you read and understand the multilingual safety instructions and the Lenovo Limited Warranty (LLW) on the documentation DVD that comes with the product. Reading and understanding the safety instructions reduces the risk of personal injury and damage to your product.

  • Page 86: Handling Static-Sensitive Devices

    • Have a small flat-blade screwdriver available. • You do not have to turn off the server to install or replace a hot-swap redundant power supply, hot-swap hard disk drives, or hot-plug USB devices. However, you must turn off the server before performing any steps that involve installing, removing, or replacing adapter cables or non-hot-swap devices or components.

  • Page 87: System Reliability Guidelines

    – Attach the ESD ground clip to any frame ground, ground braid, or green-wire ground. – When working on a double-insulated or battery-operated system, use an ESD common ground or reference point. You can use coax or connector-outside shells on these systems. –...
  • Page 88 Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Note: Depending on the model, your server might look slightly different from the illustrations in this topic. To remove the server cover, do the following: 1.

  • Page 89: Removing And Reinstalling The Front Bezel

    6. Fully open the cover latch and slide the server cover to the rear until it is disengaged from the chassis. Then, lift the server cover off the chassis and set it aside. Note: It is recommended that you wait three to five minutes to let the server cool before removing the server cover.

  • Page 90: Installing, Removing, Or Replacing Hardware

    1. Remove the three screws that secure the front bezel and then pivot the front bezel outward to remove it from the chassis. Figure 37. Removing the front bezel 2. To reinstall the front bezel, align the tabs on the bottom edge of the front bezel with the corresponding holes in the chassis.

  • Page 91: Removing And Reinstalling The Rack Handles

    Notes: • Use only parts provided by Lenovo. • Depending on the model, your server might look slightly different from the illustrations in this topic. The EMI integrity and cooling of the server are protected by having all drive bays and PCI card slots covered or occupied.

  • Page 92: Removing And Reinstalling The Cooling Shroud

    2. To reinstall the rack handles, insert the small tab on the rack handle into the hole in the chassis. Then, align the screw hole in the rack handle with the corresponding hole in the chassis and install the screw to secure the rack handle on each side of the server. Figure 40.
  • Page 93 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover. See “Removing the server cover” on page 73. 4.

  • Page 94: Removing And Reinstalling The Left Cage

    Attention: For proper cooling and airflow, reinstall the cooling shroud before turning on the server. Operating the server with the cooling shroud removed might damage server components. Removing and reinstalling the left cage Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines”...
  • Page 95 8. Remove the two screws that secure the left cage and then slide the left cage out of the front of the chassis. Figure 43. Removing the left cage 9. To reinstall the left cage, carefully route the cables from the left cage through the left cage hole in the front and then slide the left cage into the chassis until it snaps into position.

  • Page 96: Installing Or Removing A Memory Module

    10. Ensure that the two screw holes in the rear of the left cage are aligned with the corresponding holes in the chassis. Then, install the two screws to secure the left cage in position. Figure 45. Installing the screws to secure the left cage 11.
  • Page 97 For a list of the supported ThinkServer memory module options, go to: http://www.lenovo.com/thinkserver The following illustration helps you to locate the memory slots on the system board. This illustration shows a system board with two microprocessors (also known as CPU) and two heat sinks installed.
  • Page 98 The following table provides information about the memory module installation rules for servers that have only one microprocessor (CPU1) installed. The “X” mark indicates the memory slot(s) into which the memory module(s) should be installed in different situations. Note: The installed memory modules must be the same type (LV RDIMM or RDIMM) with the same rank, voltage, and frequency.
  • Page 99 The following table provides information about the memory module installation rules for servers that have two microprocessors (CPU1 and CPU2) installed. The “X” mark indicates the memory slot(s) into which the memory module(s) should be installed in different situations. Note: The installed memory modules must be the same type (LV RDIMM or RDIMM) with the same rank, voltage, and frequency.

  • Page 100: Installing A Memory Module

    Installing a memory module Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 71. This topic provides instructions on how to install a memory module. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference.

  • Page 101: Removing A Memory Module

    9. Position the new memory module over the memory slot. Ensure that the notch on the new memory module is aligned with the key in the memory slot. Then, press the new memory module straight down into the memory slot until the retaining clips close and the new memory module snaps into position. Note: If there is a gap between the memory module and the retaining clips, the memory module has not been correctly installed.

  • Page 102: Installing Or Removing An Ethernet Card

    6. Disconnect any cables that might impede your access to the memory slots. 7. Locate the memory module that you want to remove and open the retaining clips on both ends of the memory slot. Then, grasp the memory module by its edges and carefully pull it straight up to remove it from the memory slot.
  • Page 103 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface.
  • Page 104 a. Carefully remove the screws that secure the Ethernet card and then remove the full-height bracket from the Ethernet card. Figure 53. Removing the full-height bracket from the PCI Express card b. Note the orientation of the low-profile bracket and position it on the Ethernet card so that the screw holes in the low-profile bracket are aligned with the corresponding holes in the Ethernet card.
  • Page 105 Then, transfer the Ethernet card driver from the removable storage device to your server and run the driver file to install the driver. The most up-to-date device drivers for various server models are always available for download on the Lenovo Support Web site at: http://www.lenovo.com/drivers Removing an Ethernet card Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...
  • Page 106 This topic provides instructions on how to remove an Ethernet card. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • Depending on the specific type, the Ethernet card might look different from the illustrations in this topic. •...

  • Page 107: Installing Or Removing The Thinkserver Raid 500 Upgrade Key For Advanced Raid

    Advanced RAID (hereinafter referred to as the TR 500 Key). The TR 500 Key expands the capability of the ThinkServer RAID 500 Adapter by activating RAID 5 and RAID 50 for advanced SATA/SAS hardware RAID. You can purchase a TR 500 Key from Lenovo. Installing the TR 500 Key Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...
  • Page 108 6. Locate the RAID 5 key connector on the ThinkServer RAID 500 Adapter and then carefully insert the TR 500 Key into the connector. If necessary, you can remove the ThinkServer RAID 500 Adapter first, install the TR 500 Key on it, and then reinstall the ThinkServer RAID 500 Adapter. See “Replacing the RAID card”...

  • Page 109: Installing Or Removing The Thinkserver Raid 700 Battery

    1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface.
  • Page 110 alternative to using an uninterruptible power supply, and a second level of fault tolerance when used in conjunction with an uninterruptible power supply. The temperature of the TR 700 Battery is generally 15-20°C (59-68°F) higher than the ambient temperature during fast charge. Therefore, to complete a recharge cycle, the ambient temperature should be lower than 55°C (131°F).
  • Page 111 8. Position the TR 700 Battery above the ThinkServer RAID 700 Adapter so that the board-to-board connector on the bottom of the TR 700 Battery is aligned with the connector on the ThinkServer RAID 700 Adapter; and the three mounting studs on the bottom of the TR 700 Battery are aligned with the corresponding holes in the ThinkServer RAID 700 Adapter.

  • Page 112: Installing Or Removing The Expander Card

    • Use any documentation that comes with the TR 700 Battery and follow those instructions in addition to the instructions in this topic. To remove the TR 700 Battery, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server.

  • Page 113: Installing The Expander Card

    Notes: • The server must have a RAID card and an expander card installed to support more than eight hard disk drives. • The expander card is extremely sensitive to ESD. Ensure that you read and understand “Handling static-sensitive devices” on page 72 first and carefully perform the operation. Installing the expander card Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...
  • Page 114 6. There are two PCI Express card slots on the riser card assembly 1 and the shorter one is for installing the expander card. Remove the slot bracket for the shorter slot and store it in the event that you later remove the expander card and need the bracket to cover the place.

  • Page 115: Removing The Expander Card

    9. Connect cables depending on your specific server configuration. See “Mini-SAS to mini-SAS signal cable connections” on page 39. 10. Reinstall the riser card assembly 1. See “Replacing the riser card assembly 1” on page 137. What to do next: •...

  • Page 116: Installing Or Removing The Thinkserver Management Module Premium

    Therefore, working as an integrated solution in your server, the TMM Premium provides an increased level of manageability over the basic server management available. You can purchase a TMM Premium from Lenovo. ThinkServer Hardware Maintenance Manual...
  • Page 117 Installing the TMM Premium Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 71. This topic provides instructions on how to install the TMM Premium. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference.
  • Page 118 • To complete the installation, go to “Completing the parts replacement” on page 162. Then, refer to the ThinkServer Management Module User Guide, which is available for download at http://www.lenovo.com/ThinkServerUserGuides, for more information about server remote management. Removing the TMM Premium Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...
  • Page 119 Notes: • If you remove the TMM Premium, the iKVM function for server remote management is unavailable. • Use any documentation that comes with the TMM Premium and follow those instructions in addition to the instructions in this topic. • Depending on the model, your server might look slightly different from the illustration in this topic. To remove the TMM Premium, do the following: 1.

  • Page 120: Installing Or Removing The Thinkserver Trusted Platform Module

    The TPM is a security chip designed by the Trusted Computing Group (TCG) to provide a hardware method of data encryption. It stores passwords, encryption keys, and digital certificates to help provide security solutions and protect the computer. You can purchase a TPM option from Lenovo. Installing the TPM Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...

  • Page 121: Removing The Tpm

    6. Insert the TPM into the TPM connector on the system board. Figure 66. Installing the TPM 7. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card assembly 1” on page 137. What to do next: •...
  • Page 122 Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • If you remove the TPM, the TPM function will be unavailable. • Use any documentation that comes with the TPM and follow those instructions in addition to the instructions in this topic.

  • Page 123: Installing Or Replacing A Hot-Swap Redundant Power Supply

    5. Remove the TPM installed on the TPM connector by lifting it straight up. Note: Carefully handle the TPM by its edges. Figure 67. Removing the TPM 6. If you have lifted up the riser card assembly 1, reinstall it into the chassis. See “Replacing the riser card assembly 1”...
  • Page 124 This topic provides instructions on how to install or replace a hot-swap redundant power supply. The hot-swap redundant power supplies help you avoid significant interruption to the operation of the system when a power supply fails. You can install or replace a hot-swap redundant power supply without turning off the server.
  • Page 125 • If you are installing a hot-swap redundant power supply, locate the bay for the power supply in the rear of your server. Insert a finger into the hole in the metal shield that protects the bay, press the tab in the direction as shown, and then pull the shield out of the chassis.
  • Page 126 2. If you are replacing a hot-swap redundant power supply, press the release tab in the direction as shown and carefully pull the handle at the same time to slide the failing hot-swap redundant power supply out of the chassis. Figure 69.

  • Page 127: Installing Or Replacing A Heat Sink

    5. Connect the power cord to the power cord connector on the new hot-swap redundant power supply. Then, check the status LED near the power cord connector. When the LED is lit in green, it indicates that the hot-swap redundant power supply is working correctly. When the LED is lit in amber, it indicates that the hot-swap redundant power supply is likely to fail or has failed.
  • Page 128 6. If you are replacing a heat sink, remove the four screws that secure the heat sink to the system board. It is recommended that you carefully remove the four screws from the system board using the following method to avoid any possible damage to the system board. a.

  • Page 129: Installing Or Replacing The Microprocessor

    10. Install the four screws to secure the new heat sink on the system board. It is recommended that you carefully install the four screws using the following method to avoid any possible damage to the system board. a. Partially tighten screw , then firmly tighten screw , and then return to screw and firmly tighten...
  • Page 130 1 and the microprocessor socket 2 is protected by a plastic socket cover. You can purchase a microprocessor option kit from Lenovo and install the second microprocessor to expand system capabilities.
  • Page 131 7. Gently press the microprocessor retainer as shown to open it. Ensure that the small handles and the microprocessor retainer are in the fully open position. Note: Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible.
  • Page 132 10. Note the orientation of the new microprocessor. Hold the new microprocessor by its edges and align the notches on it with the tabs in the microprocessor socket. Then, carefully lower the new microprocessor straight down into the microprocessor socket. Note: The small triangle on one corner of the new microprocessor is the microprocessor orientation indicator.

  • Page 133: Replacing The Microprocessor

    12. Close the microprocessor retainer. Press down the small handle first and then push the handle inward to secure it. Then, press down the small handle and then push the handle inward to lock the retainer into position and secure the new microprocessor in the socket. Note: There are two marks on the microprocessor retainer.
  • Page 134 Notes: • Ensure that the new microprocessor is the correct type your server supports. See “Features” on page 8. When two microprocessors are installed, both must have the same core voltage and core speed. • Use any documentation that comes with the microprocessor option kit and follow those instructions in addition to the instructions in this topic.
  • Page 135 7. Gently press the microprocessor retainer as shown to open it. Ensure that the small handles and the microprocessor retainer are in the fully open position. Figure 80. Opening the microprocessor retainer 8. Touch only the edges of the microprocessor and carefully lift it straight up and out of the microprocessor socket.
  • Page 136 10. Remove the new microprocessor from the protective cover that protects the gold contacts on the bottom of the new microprocessor. Do not touch the pins on the microprocessor socket and the gold contacts on the bottom of the new microprocessor. Figure 82.

  • Page 137: Installing Or Replacing The Optical Drive

    12. Close the microprocessor retainer. Press down the small handle first and then push the handle inward to secure it. Then, press down the small handle and then push the handle inward to lock the retainer into position and secure the new microprocessor in the socket. Note: There are two marks on the microprocessor retainer.
  • Page 138 DANGER Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following: Laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference.
  • Page 139 • If you are replacing an optical drive, disconnect the signal cable and the power cable from the rear of the optical drive. Press the rear of the retaining bracket in the direction as shown and push the optical drive from the rear until it is projected from the front of the chassis. Then, hold the optical drive from the front and completely slide it out of the chassis.
  • Page 140 7. Remove the retaining bracket from the old optical drive or the dummy optical drive tray. Then, install it on the side of the new optical drive. Figure 87. Installing the optical drive retaining bracket ThinkServer Hardware Maintenance Manual...
  • Page 141 8. Slide the new optical drive with the retaining bracket into the drive bay from the front until it snaps into position. Figure 88. Installing the optical drive for server models with 3.5-inch hard disk drives Figure 89. Installing the optical drive for server models with 2.5-inch hard disk drives Chapter 6 Installing, removing, or replacing hardware...

  • Page 142: Installing Or Replacing A Hot-Swap Hard Disk Drive

    This topic provides instructions on how to install or replace a hot-swap hard disk drive. For a list of the ThinkServer hard disk drive options, go to: http://www.lenovo.com/thinkserver You can install or replace a hot-swap hard disk drive without turning off the server, which helps you avoid significant interruption to the operation of the system.
  • Page 143 • For hard disk drives with different capacities, install the hard disk drives following the order of the hard disk drive bays as well as the order from the lowest capacity to the highest capacity. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference.
  • Page 144 Figure 92. Opening the handle of a 2.5-inch hot-swap hard disk drive or dummy tray 2. Pull the handle and carefully slide the hot-swap hard disk drive or the dummy tray out of the front of the chassis. Figure 93. Removing the 3.5-inch hot-swap hard disk drive or dummy tray ThinkServer Hardware Maintenance Manual...
  • Page 145 Figure 94. Removing the 2.5-inch hot-swap hard disk drive or dummy tray 3. Touch the static-protective package that contains the new hot-swap hard disk drive to any unpainted surface on the outside of the server. Then, take the new hot-swap hard disk drive out of the package. Note: Do not touch the circuit board on the hard disk drive.

  • Page 146: Replacing The Hot-Swap Hard Disk Drive Backplane

    Figure 96. Installing the 2.5-inch hot-swap hard disk drive 5. Check the hot-swap hard disk drive status LEDs to ensure that the hard disk drive is operating correctly. You might have to restart the server for the newly installed hard disk drive to be recognized. See “Hot-swap hard disk drive status LEDs”...
  • Page 147 Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • This topic applies only to server models that support 3.5-inch hot-swap hard disk drives. • To clearly show the backplane, the system fans are omitted from the illustrations in this topic. To replace the backplane for 3.5-inch hard disk drives, do the following: 1.
  • Page 148 8. Carefully lift the backplane straight up a little bit so that the small hooks on the chassis are aligned with the corresponding holes in the backplane. Then, slowly and carefully move the backplane to the rear of the chassis until the hooks pass through the holes in the backplane and then completely remove the backplane out of the chassis.
  • Page 149 11. Press the buttons to put the latches on the chassis to the closed position so that the latches secure the new backplane in place. Figure 100. Securing the backplane for 3.5-inch hard disk drives 12. Reinstall all the hot-swap hard disk drives and dummy trays (if any) in the hard disk drive bays. See “Installing or replacing a hot-swap hard disk drive”...
  • Page 150 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface.

  • Page 151: Replacing The Riser Card Assembly 1

    9. Note the orientation of the new backplane. Carefully press the new backplane straight down into the chassis so that it is secured in place by the tabs on the chassis and the three screw holes in the new backplane are aligned with the corresponding holes in the chassis. Then, install the screws to secure the new backplane in place.
  • Page 152 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface.

  • Page 153: Replacing The Riser Card Assembly 2

    11. Position the new riser card assembly 1 on the chassis and align it with the riser card assembly 1 slot on the system board and align the rear of it with the corresponding rail guides in the rear of the chassis. Then, carefully press the new riser card assembly 1 straight down into the chassis until it is fully seated.
  • Page 154 2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat, clean, and static-protective surface. See the Rack Installation Instructions that comes with the server. 3. Remove the server cover. See “Removing the server cover” on page 73. 4.

  • Page 155: Replacing The Raid Card

    10. Position the new riser card assembly 2 on the chassis and align it with the riser card assembly 2 slot on the system board and align the rear of it with the corresponding rail guides in the rear of the chassis. Then, carefully press the new riser card assembly 2 straight down into the chassis until it is fully seated.
  • Page 156 Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • The RAID card is extremely sensitive to ESD. Ensure that you read and understand “Handling static-sensitive devices” on page 72 first and carefully perform the operation. •...

  • Page 157: Replacing The Front Panel Board

    9. Note the dotted lines in the following illustration to properly position the new RAID card near the longer PCI Express card slot on the riser card assembly 1. Then, carefully press the new RAID card straight into the slot until it is securely seated and its bracket also is secured by the riser card assembly 1. Figure 108.
  • Page 158 Notes: • The front panel board is extremely sensitive to ESD. Ensure that you read and understand “Handling static-sensitive devices” on page 72 first and carefully perform the operation. • Depending on the model, your server might look slightly different from the illustrations in this topic. Replacing the front panel board for server models with 3.5-inch hard disk drives Attention: Do not open your server or attempt any repair before reading and understanding “Safety information”...
  • Page 159 8. Carefully position the new front panel board on the chassis so that the front controls, connectors, and LEDs are through the corresponding holes in the front bezel and the two screw holes in the new front panel board are aligned with the corresponding mounting studs on the chassis. Then, install the screws to secure the front panel board in place.
  • Page 160 8. Disconnect the front panel cable and the front panel USB cable from the rear of the front panel board. 9. Remove the two screws that secure the front panel board and then carefully remove the front panel board from the left cage. Figure 111.

  • Page 161: Replacing The Diagnostic Module

    What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 162. Replacing the diagnostic module This topic provides instructions on how to replace the diagnostic module. For detailed information about the diagnostic module, see “Diagnostic module”...
  • Page 162 6. Press the release tab in the direction as shown and then push the diagnostic module out of the front of the chassis. Figure 113. Removing the diagnostic module for server models with 3.5-inch hard disk drives 7. Touch the static-protective package that contains the new diagnostic module to any unpainted surface on the outside of the server.
  • Page 163 10. If you are instructed to return the old diagnostic module, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. What to do next: • To work with another piece of hardware, go to the appropriate section. •...

  • Page 164: Replacing A System Fan

    12. Slide the new diagnostic module into the cage from the front until it snaps into position. Figure 116. Installing the diagnostic module into the left cage of server models with 2.5-inch hard disk drives 13. Connect the diagnostic module cable to the rear of the new diagnostic module. 14.
  • Page 165 To replace a system fan, do the following: 1. Remove the server cover. See “Removing the server cover” on page 73. Note: The system fans are hot-swap and you can replace a failing system fan without turning off the server. 2.

  • Page 166: Replacing The System Board Battery

    5. Position the new system fan above the place for the removed failing system fan so that the system fan connector on the bottom of the new system fan is facing the rear of the chassis. Then, press the new system fan straight down until it is seated into place.
  • Page 167 • Heat to more than 100°C (212°F) • Repair or disassemble Dispose of the battery as required by local ordinances or regulations. The following statement applies to users in the state of California, U.S.A. California Perchlorate Information: Products containing manganese dioxide lithium coin cell batteries may contain perchlorate. Perchlorate Material - special handling may apply, Seehttp://www.dtsc.ca.gov/hazardouswaste/perchlorate Before you begin, print all the related instructions or ensure that you can view the PDF version on another...

  • Page 168: Replacing The System Board

    “Guidelines” on page 71. This topic provides instructions on how to replace the system board. Note: This procedure must be performed only by trained service personnel of Lenovo. CAUTION: Hazardous moving parts. Keep fingers and other body parts away.
  • Page 169 Note: Depending on the model, your server might look slightly different from the illustrations in this topic. To replace the system board, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server.
  • Page 170 9. Remove the power supply cooling shroud. Figure 122. Removing the power supply cooling shroud 10. Remove all memory modules. See “Removing a memory module” on page 87. 11. Remove the TMM Premium if one is installed. See “Removing the TMM Premium” on page 104. 12.
  • Page 171 15. Disconnect all cables from the system board. Then, remove the ten screws that secure the system board following the recommended numerical sequence as shown. Figure 123. Removing the screws that secure the system board Chapter 6 Installing, removing, or replacing hardware...
  • Page 172 16. Gently lift each edge of the system board a little bit upward so that the system board is completely released from the mounting studs on the chassis. Then, move the system board to the front of the server and then carefully pivot the system board upward to remove it out of the chassis. Note: Carefully handle the system board by its edges.
  • Page 173 19. Install the ten screws following the recommended numerical sequence as shown to secure the new system board on the chassis. Figure 126. Installing the screws to secure the system board 20. Remove the microprocessor(s) from the old system board and install them on the new system board. See “Installing or replacing the microprocessor”...
  • Page 174 a. Close the microprocessor retainer. Press down the small handle first and then push the handle inward to secure it. Then, press down the small handle and then push the handle inward to lock the microprocessor retainer into position. Notes: •...
  • Page 175 24. Note the orientation of the power supply cooling shroud and install it into the chassis by inserting the two small tabs on the bottom of the shroud into the corresponding holes in the power supply cage. Figure 129. Installing the power supply cooling shroud 25.

  • Page 176: Completing The Parts Replacement

    30. Install any other parts that you have removed and connect all cables to the new system board. Refer to the information that you have noted down and the related topics in “Installing, removing, or replacing hardware” on page 76. 31.
  • Page 177 2. Ensure that all internal cables are connected and routed correctly and secured by any cable clips or ties in the server. Keep cables clear of the hinges and sides of the chassis to avoid interference with reinstalling the cooling shroud and the server cover. The following illustration shows an example of the cable routing in the chassis with two backplanes for 16 2.5-inch hard disk drives.
  • Page 178 5. Ensure that the cover latch is in the open position. Place the server cover above the chassis so that the cover latch is aligned with the cover latch slot in the chassis. Then, lower the server cover onto the chassis until the cover latch is inserted into its slot and both sides of the server cover engage the guides on both sides of the chassis.

  • Page 179: Updating The Server Configuration

    Attention: To avoid component damage, connect the power cord(s) last. Note: In most areas of the world, Lenovo requires the return of the defective CRU. Information about this will come with the CRU or will come a few days after the CRU arrives.
  • Page 180 ThinkServer Hardware Maintenance Manual...

  • Page 181: Chapter 7. Troubleshooting And Diagnostics

    For information about the LEDs, refer to the related topics in “Locations” on page 14. Viewing the system event log The system event log (SEL) contains information about all the POST and system management interrupt (SMI) events. You can view the SEL to diagnose system problems. © Copyright Lenovo 2012...

  • Page 182: Basic Troubleshooting Tables

    TMM in-band and out-of-band interfaces. For more information about viewing the SEL, refer to the ThinkServer Management Module User Guide, which is available for download at: http://www.lenovo.com/ThinkServerUserGuides Basic troubleshooting tables Use the basic troubleshooting information to find solutions to problems that have definite symptoms.

  • Page 183: Hard Disk Drive Problems

    • If an action step is preceded by “(Trained service technician only),” this action step is reserved for a trained service technician and must be performed only by a trained service technician. Action Symptom The optical drive is not recognized. 1.

  • Page 184: Memory Module Problems

    Notes: • If you are instructed to remove, install, or replace any CRUs, refer to the related procedure in Chapter 6 “Installing, removing, or replacing hardware” on page 71. • The status LEDs on each hot-swap hard disk drive help you easily identify a problem. See “Hot-swap hard disk drive status LEDs”...

  • Page 185: Keyboard, Mouse, And Usb Device Problems

    • If an action step is preceded by “(Trained service technician only),” this action step is reserved for a trained service technician and must be performed only by a trained service technician. Action Symptom The amount of system memory that is displayed is less 1.
  • Page 186 Symptom Action 3. Replace the mouse or pointing device. A USB device does not work. 1. Ensure that: • The USB cable is securely connected to the server. If the USB device is connected to a USB hub, disconnect the device from the hub and connect it directly to the server.

  • Page 187: Chapter 8. Getting Information, Help, And Service

    Using the documentation Information about your Lenovo system and installed software, if any, or optional device is available in the documentation that comes with the product. The documentation can include printed documents, online documents, readme files, and help files. Most of the documentation for your server is on the documentation DVD provided with your server.

  • Page 188: Help And Service

    • Check the power switches to ensure that the system and optional devices are turned on. • Use the troubleshooting information in your system documentation on the documentation DVD that comes with your product. • Check for the updated information, new device drivers, and hints and tips on the Lenovo Support Web site at: http://www.lenovo.com/support If possible, be at your product when you call.

  • Page 189: Using Other Services

    Service availability and service names might vary by country or region. For more information about these services, go to the Lenovo Web site at: http://www.lenovo.com...
  • Page 190 ThinkServer Hardware Maintenance Manual...

  • Page 191: Appendix A. Notices

    Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead.

  • Page 192: Trademarks

    Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products. For information on recycling Lenovo products, go to: http://www.lenovo.com/recycling...

  • Page 193: Battery Return Program

    The battery must be recycled or disposed of properly. Recycling facilities may not be available in your area. For information on disposal or batteries outside the United States, go to http://www.lenovo.com/recycling or contact your local waste disposal facility. Battery recycling information for the United States and Canada Battery recycling information for the European Union Notice: This mark applies only to countries within the European Union (EU).

  • Page 194: Particulate Contamination

    If Lenovo determines that the levels of particulates or gases in your environment have caused damage to the server, Lenovo may condition provision of repair or replacement of servers or parts on implementation of appropriate remedial measures to mitigate such environmental contamination.
  • Page 195 Auswirkungen der Geräte auf die Umwelt und den menschlichen Organismus aufgrund gefährlicher Substanzen minimiert werden. Weitere Informationen zur Entsorgung von Elektro- und Elektronikaltgeräten finden Sie unter der Adresse: http://www.lenovo.com/recycling. La marca de Residuos de equipos eléctricos y electrónicos (WEEE) se aplica sólo a los países pertenecientes a la Unión Europea (UE) y a Noruega.
  • Page 196 REEE, por forma a minimizar potenciais efeitos dos EEE sobre o ambiente e saúde pública resultantes da presença de substâncias perigosas. Para obter informações adicionais acerca da REEE consulte o sítio da web: http://www.lenovo.com/recycling. Het WEEE-merkteken (Waste Electrical and Electronic Equipment) geldt alleen voor landen binnen de Europese Unie (EU) en Noorwegen.
  • Page 197 å redusere en eventuell skadelig virkning av elektrisk og elektronisk utstyr på miljø og helse, som skyldes skadelige stoffer. Du finner mer informasjon om WEEE på denne adressen: http://www.lenovo.com/recycling. Appendix A. Notices...

  • Page 198: German Ordinance For Work Gloss Statement

    For more information about ENERGY STAR, go to: http://www.energystar.gov Lenovo encourages you to make efficient use of energy an integral part of your day-to-day operations. To help in this endeavor, set the following power-management features to take effect when your servers...
  • Page 199 • Processor- or core-reduced power states • Variable speed fan control based on power or thermal readings • Low power memory states • Liquid cooling capability Appendix A. Notices...
  • Page 200 ThinkServer Hardware Maintenance Manual...

  • Page 201: Index

    BIOS completing the replacement front bezel reinstalling removing front panel devices, handling static-sensitive locations diagnostic module front panel board locations replacing replacing front view of the server diagnostic panel locations locations © Copyright Lenovo 2012...
  • Page 202 Lenovo Rack Planner hot-swap redundant power supply status software Lenovo ThinkServer EasyManage software Lenovo ThinkServer EasyManage program using information, getting locations Input/Output (I/O) features installation rules DIMM memory module machine type, model, and serial number label...
  • Page 203 Server Management menu rack handles Setup Utility program reliability, availability, and serviceability server package features server setup remote management road map software service, getting removing setting, changing, deleting cooling shroud password © Copyright Lenovo 2012...
  • Page 204 BIOS system status using documentation system time EasyUpdate Firmware Updater program setting Lenovo ThinkServer EasyManage program passwords Setup Utility program ThinkServer EasyStartup program the BIOS flashing recovering updating video subsystem updating or recovering...
  • Page 205 Setup Utility program Web site compatible options working inside the server with the power on guidelines © Copyright Lenovo 2012...
  • Page 206 ThinkServer Hardware Maintenance Manual...

Table of Contents