Warranty; Safety Instructions - Craftsman 113.225930 Owner's Manual

FULL ONE YEAR WARRANTY ON CRAFTSMAN BELT AND DISC SANDER
This warranty gives you specific legal! rights, and you may also have other rights which vary from state to
state:,
SEARS. ROEBUCK AND CO.. Dept. 698/731A. Sears Tower, Chicago, I L 60684
general safety instructions for power
1, KNOW YOUR POWER TOOL
Read and understand the owner's manual and labels
affixed to the toot, Learn its application and limitations as
well as the specific potential hazards peculiar to this tool.
mask if cutting operation is dusty, and ear protectors
(plugs or muffs} during extended periods of operation.
13. SECURE WORK
2. GROUND ALL TOOLS
This toot is equipped with an approved 3-conductor
€o_d arid a 3-prong grounding type plug to fit the proper
grounding type receptacle. Th =. green conductor in the
cord is the grounding wire, Never connect the green wire
to a live terminal.
3, KEEP GUARDS IN PLACE
- in working order, and in proper adjustment and align-
ment.
4, REMOVE ADJUSTING KEYS AND WRENCHES
Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
5. KEEP WORK AREA CLEAN
Ciuttered areas and benches inwte accidents. Floor
must not be slippery due to wax or sawdust.
6: AVOID DANGEROUS ENVIRONMENT
Use clamps or a vMse to hold work when practical. It's
safer than using your hand, frees both hands to operate
tool.
14. DON'T OVERREACH
Keep proper footing and balance at all times.
15. MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest perform_
ance. Follow instructions for lubricating and changing
accessories.
16. DISCONNECT TOOLS
before servicing; when changing accessories such as
blades, bits, cutters, etc.
17. AVOl D ACCIDENTAL STARTING
Make sure Switch is tn "OFF" posntlon before plugging
n
.
n r .................. 18 USE
Don't use power tools in :damp orwet tocatio ::::::::::::::::::::::::::::: RECOMMENDED ACCESSORIES
;_ose them to rain. Keep work area well lighted. P:t6:_i_le .... Consult the owner's manual for recommended accessories.
adequate surroundingw0rk space,,
.....
KEEP CHILDREN AWAY
All visitors should be kept a safe distance from worl(:area:
8. MAKE WORKSHOP KID-PROOF
with padlocks, master swmtches, or by removing starter
keys.
9. DON'T FORCE TOOL
I1 wdl do the job better and safer at the rate for which
_t was desngned
10. USE RIGHT TOOL
Don't force too! or attachment to _o a ?oh _t was not
designed for
11. WEAR PROPER APPAREL
Do not wear loose clothing, gloves, neckties or jewelry
{rings, wristwatches) to get caught _n moving pa_'ts
NONSLIP footwear is recommended. Wear protective
hall covering to contain
long
hair. Roll long sleeves
above the elbow.
Follow the instructions that accompany the accessories.
The use of improper accessorues may cause hazards.
i:::::iii:i ::!9:iNEVER STAND ON TOOL
.: Serious injury could occur if the tool is tipped or if the
cutting tool is accidentally contacted.
Do not store materials above or near the tool such that
it _s necessary to stand on the tool to reach them,
20. CHECK DAMAGED PARTS
Before further use of the tool. a guard or other part that
=s damaged should be carefully checked to ensure that it
will operate properly and perform its intended function
Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other con,
dtt=ons that may affect its operation. A guard or other
_)art that is damaged should be properly repaired or
replaced
21. DIRECTION OF FEED
Feed work into a blade or cutter against the d_rect_on of
rotation of the blade or cutter only.
12, USE SAFETY GOGGLES (Head Protection)
Wear safety goggles (must comply with ANSI Z87.t) at all
times. Everyday: eyeglasses only have impact resistant
lenses, they are NOT safety glasses. Also, use face or dust
22. NEVER LEAVE TOOL RUNNING
UNATTENDED
Tu=n power off. Don't leave tool until it comes to a
corn _lete stop