Download Print this page

Epson 26-484-01 Installation Instructions

Hide thumbs
   

Advertisement

Epson Installation
PROJECTOR COMMUNICATIONS KIT
PLEASE READ THIS DOCUMENT FOR IMPORTANT
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: EPSON
Included Communications Adapter(s):
Quantity
1
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER'S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE " " IN THE "Config as" COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR:
Config
Model
as
EMP 5300/7100
EMP 7300/7550
EMP 8000/7250
EMP 8100/7700
EMP 7600/5600
Extron • System 8/10 P
LUS
SYSTEM 8/10 Plus
ATTENTION!
INSTALLATION INSTRUCTIONS
Part Number
26-484-01
Rotary Switches Cable
RS1 RS2 RS3 RS4 J2/J3 1 2 3 4 5 6 7 8 9 10 Adapter
0
0
E
0
0
E
0
0
E
1
0
E
2
0
E
• User's Manual • P/N 68-424-01 Rev. D
Configuration and Connections
Description
ADP, UNV, "I"
EPSON EMP 5300/7100/
7300/7550
SW15 Settings
2
J2
2
J2
6
J2
6
J2
6
J2
Comm
26-484-01
26-484-01
26-484-01
26-484-01
26-484-01
Page 1

Advertisement

   Related Manuals for Epson 26-484-01

   Summary of Contents for Epson 26-484-01

  • Page 1

    Configuration and Connections SYSTEM 8/10 Plus PROJECTOR COMMUNICATIONS KIT ATTENTION! PLEASE READ THIS DOCUMENT FOR IMPORTANT INSTALLATION INSTRUCTIONS THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS: Kit Type: EPSON Included Communications Adapter(s): Quantity Part Number Description 26-484-01 ADP, UNV, “I”...

  • Page 2

    ______ Secure the screws on all D connectors. 8. Connect the BNC (RGBS) cables from the System 8/10 P outputs to the Epson projector inputs according to the application requirements. 9. Apply Main Power to the System 8/10 P by connecting the power cord. The Main Power LED should light.

  • Page 3

    30 to 60 seconds when powering the projector on/off using the System 8/10 Plus. Epson 5300/7300 Projector Connections Use the illustration below when connecting the System 8/10 P to an Epson 5300/7300 projector. Refer to Epson documentation to continue the installation. 9-Pin See note below...

  • Page 4

    ______ Secure the screws on all D connectors. 8. Connect the BNC (RGBS) cables from the System 8/10 P outputs to the Epson projector inputs according to the application requirements. 9. Apply Main Power to the System 8/10 P by connecting the power cord. The Main Power LED should light.

  • Page 5

    30 to 60 seconds when powering the projector on/off using the System 8/10 Plus. Epson 8000/7250 Projector Connections Use the illustration below when connecting the System 8/10 P to an Epson 8000/7250 projector. Refer to Epson documentation to continue the installation. 9-Pin Comm Male "I"...

Comments to this Manuals

Symbols: 0
Latest comments: