Quickly find answers to your questions by: 1. Reading your owner’s manual, included with this product. 2. Visiting our customer support website at www.uniden.com. 3. Calling our customer care specialists at 1-817-858-2900 or 1-800-658-8068.
Pairing ..................... 20 Uniden surveillance products are not manufactured and/or sold with the intent to be used for illegal purposes. Uniden expects consumer’s use of these products to be in compliance with all local, state and federal law. For further information on video surveillance and audio recording legal requirements, please consult your local, state and federal law.
IntroDuCtIon Features 2.4GHz Digital FHSS • 4.3” high-resolution touchscreen LCD • Easy to use graphic interface • Secure, interference-free video • Up to 500’ wireless transmission • Video and audio transmission • Quad, Scan, and Full screen view • Supports up to 4 cameras •...
This manual is set up in six main sections: Getting Started. This section describes your hardware and how to physically set it up. • Uniden Guardian™ Lullaboo Firmware Operations Overview. This section lists basic operations in • an abbreviated format. It references screen details in the third section.
GettInG to KnoW the monItor anD Camera Monitor Cradle Antenna (back/side) Reset Receiver Power Power Dock On/O Data Cable Connection SD slot AC Power Connection AC Power Pull-Out Connection Stand Camera Antenna Light Sensor Power IR LEDs Link Lens DC Jack Charge Link Power Microphone LEDs...
3 - 4 seconds to power it up. PoWer 4. The monitor displays the Uniden Welcome screen for a few seconds and then transitions to the LIVE view. The screen remains dark until the camera is powered up.
mount the Camera stanD General Guidelines The camera included with your monitor is NOT weatherproof; it is an indoor camera. As dust, grime, and cobwebs accumulate on the camera glass, they can reflect light from the infrared LED and might lower video quality. Periodically clean the lens glass with a soft cloth. Placement considerations Consider the following when placing a camera: The clearest line-of-sight between the camera and monitor is best.
attaCh the Camera Place the stand swivel mount over the camera’s stand connection and slide the mount to the left until it clicks in place. ConneCt to PoWer 1. Insert the AC adapter power plug into the camera’s DC adapter input jack. Plug the other end into a 120 volt AC (standard indoor) power outlet.
Language (default language is English; “Changing the Language” on page 36) • reCorDInG settInGs Motion Detection (“Motion Detection” on page 22) • Schedule Recordings (“Schedule Record” on page 25) •...
GuarDIan LuLLaBoo FIrmWare oPeratIon oVerVIeW Your baby monitor uses Uniden Guardian Lullaboo firmware to operate a series of screens that lets you choose groups of operations. For example, when you tap on the camera icon in the Pop Up menus, you can set how you want the main viewing screen - called the live screen - to display images from the paired cameras.
• Quad view (all paired cameras display) • Full view (1 camera displays on full screen) VoLumE Adjust the volume level. unIDEn GuarDIan LuLLaboo FIrmWarE Access the Uniden Guardian Lullaboo Firmware operation screens or view SEttInGS recorded events. SD CapaCIty Indicates memory capacity remaining. battEry CapaCIty Displays battery capacity.
Page 13
Icon What it does Appears in Live view. Indicates remote viewing is in progress. Appears in Live view. Indicates system is not connected to the internet. Appears in Live view. Indicates the intranet connection is established. CamEra numbEr Displays the camera number and signal strength through the status lines to the left of the number.
ChanGInG hoW the LIVe sCreen DIsPLaYs The Live screen displays in 2 views - Quad view or Full view. Quad view divides the screen’s image area into 4 quadrants and displays camera video in each quadrant. If less than 4 cameras are on, only those cameras’...
usInG Your sYstem reCorDInG LIVe VIDeo 1. On the live screen, tap for the camera to begin recording. 2. Tap it again to stop recording. You can record from all cameras at the same time. PLaYInG BaCK reCorDeD VIDeo From the pop-up menus, tap The Record List screen displays.
aDDInG neW Cameras Your monitor supports a total of four active cameras at a time. When you add a camera, you have to pair it to the monitor (that is, you have “introduce” the camera and monitor so they can communicate).
Page 17
troubleshootinG camera PairinG Consult the following table for camera pairing troubleshooting suggestions: If... try... • making sure the camera is plugged in and the blue LED is on. • making sure that both the camera’s and the monitor’s antennas are extended. the camera’s signal status icon shows no bars •...
GuarDIan LuLLaBoo sCreen DesCrIPtIon oVerVIeW This section describes the Guardian Lullaboo firmware screens in detail. It provides a path to the screen being viewed. GuarDIan LuLLaBoo settInGs sCreen From the pop-up menu, tap the This screen should display: following icons as they appear on the screens: ...
Page 19
main Screen Sub Screens What it Does Select the type of internet connection to be used. (DHCP Network Setup Internet Setup is most common.) Security Code Set a security code for remote access. Network Information Displays information about your network and the monitor’s unique DID number.
Camera setuP sCreen PaIrInG Your camera is paired to the monitor at the factory to channel 1. When you add a new camera to your system, you have to pair it to the monitor (that is, you have “introduce” the camera and monitor so they can communicate).
Camera on When you add a camera to your system, pair the camera with the monitor and the system will automatically turn it on. An X indicates a camera that is turned off; a check mark indicates the camera is turned on. From the pop-up menu, tap the This screen should display: following icons as they appear...
briGhtness From the pop-up menu, tap the This screen should display: following icons as they appear on the screens: Tap the camera whose brightness level you want to change. The default brightness is 0, and the range is from -2 through 2.
Page 23
In order to enable this e-mail alert, you must enter both incoming and outgoing email addresses. Uniden recommends you use Gmail to set up as the outgoing email server. The outgoing email server (SMTP server) is responsible for sending out the email notification to tell users when motion is detected (Motion Detection must be activated).
Page 24
1. Tap enable to activate Email Alert or disable to deactivate it. 2. Tap on the smtP server field. A keyboard screen displays. 3. Enter your outgoing e-mail SMTP server (example: johndoe@gmail.com). You can switch the keyboard from alphabetical characters to numbers/symbols and back again by tapping the field to the left of the space bar.
For Gmail SMTP Server Smtp.gmail.com Enter this. SMTP Port Enter this. Username XXXX@gmail.com Enter your gmail address in full, including @gmail.com. Password XXXXXXXXXX Enter the password for this gmail account. Email to XXXX@gmail.com Enter the email address where you want the alerts sent. schedule record You can schedule up to 5 recording sessions.
4. Tap on the blank Date box. The recorder setup calendar screen displays. 5. Tap on the date you want the recording. The previous screen displays. 6. Set up the recording and then tap . You can select saVe another recording session to schedule, return the previous screen, or return to the live screen.
Page 27
internet setuP 1. Tap Internet Setup icon to display the internet setup screen. 2. Tap on your selection and fill in the fields requested. Tap Selection Fields Static IP • IP Address • Subnet Mask • Default Gateway • DNS Server DHCP None 3.
Page 28
2. If you have not entered a security code, you can enter it here. If you have previously entered a security code, your current security code displays. The default security code is set to 123456. We recommend that you change this code to something you will remember.
netWork information screen 1. Tap the Network Information icon to display the network information screen. 2. Tap the arrow to return to the previous screen. The DID is a unique code specific to your monitor and is required (along with the security code) to gain remote access to your camera over the internet.
Page 30
Period screen This selection allows you to select the length of time the alarm will sound for the alarm clock. 1. Tap Period. The change siren duration screen displays. 2. Tap the duration you want the siren to last (2, 10, or 30 seconds) or tap None to turn sirens off. 3.
2. A check mark appears on the melody you tap and the monitor briefly plays a sample of the selected melody. 3. Tap the BACK arrow to return to the previous screen. sYstem setuP sCreen PoWer savinG When you turn on Power Saving mode, the monitor goes into sleep mode (LCD turns off) after it is idle for 2 minutes.
Page 32
2. A check mark appears on your selection. 3. Tap to return to the previous screen. screen auto lock When you turn on Auto Lock mode, the monitor will automatically enter screen lock mode after it has been idle for 2 minutes. Auto Lock disables the touchscreen and removes the icons from the display.
Page 33
time The time screen lets you set up clock alarms, set the system time, and set a timer. From the pop-up menu, tap the The following screen displays: following icons as they appear on the screens: clock alarm This feature operates as an independent alarm clock.
Page 34
4. Tap on the minute block. The arrows move to the minute block. Set the minute. uP/DoWn 5. Tap on to toggle between the two. am/Pm 6. Tap when you are finished. saVe time settinG This screen contains fields to set the Month, Day, Year, Hour, Minute, and AM/PM. 1.
timer This feature operates as an independent timer. It does not affect the operation of live video or recording video. 1. Tap to display the timer screen. 2. Tap on each field to set it. The arrows shift to that field. Use to set the field.
3. The system indicates success or failure. sYstem uPGraDe To upgrade the Uniden Guardian Lullaboo firmware, you will need to download the file from the Uniden website (www.uniden.com) to your computer. This file must then be transferred to the root directory of the SD card used in your Lullaboo baby monitor.
From the pop up menus, tap This screen should display: the following icons as they appear on the screens: 1. Select a language to change to that language. The restore default settings screen displays. 2. Tap to continue with the language reset.
Uniden’s Lullaboo baby monitor lets you view live video from your Windows® PC, an iPhone®, iPad®, or Android smartphone or tablet. Free apps are available through the iTunes® App Store or the Android Market. This system uses P2P remote access technology and does not require configuring your router, port forwarding or a remote DDNS service.
2. Connect the other end into your primary router (typically, the router from your service provider). 3. Place cradle maximum distance away from your router. 4. Insert the monitor into the cradle. A screen asks if you want to connect to the internet or to only charge the monitor.
Page 40
1. From your Android smart phone or tablet device, search the Android Market for uniden Guardian. 2. Download and install this app to your device. 3. Launch the app; select add to add your system information to the app. 4. Enter a name for your system in the system name field.
Page 41
aPP oPeration When you open the APP on your Android phone, the image displayed on the main screen is the last camera image, captured automatically, from your previously established session. Tap to add an additional Guardian system. Tap to enter System Setup page. Tap to refresh the system.
In a similar fashion to the Android smart phone, you can use the Apple® iPhone® smart phone or iPad® tablet with your Lullaboo system to remotely connect to and view camera videos. Follow these steps to download the Uniden Guardian iPhone® App and set it up to work with your Lullaboo.
Page 43
Tap to add an additional Guardian system. Tap to enter System Setup page. Tap to refresh the system. Tap to enter the APP Information page. The screen displays the APP version number and the API version number. Tap OK to exit. Main screen If you have multiple systems, scroll down and tap on the system image you want to view.
soLVInG ProBLems If you have any trouble with your system, try these simple steps. If you are still having a problem with your camera, check the manual that came with your camera. If you still have a question, call our Customer Care Line; see “Customer Care” on page 2. If…...
Page 45
If… try.. • Making sure the camera is plugged in and the blue (Power) LED is on and the yellow (Pairing) LED is flashing. The camera won’t pair with the monitor • Pressing and releasing the pairing button quickly. Do not press and hold the pairing button.
Auto System Specifications Camera monitor Weight 4.1 oz (118 g) G403: 7 oz (198 g) Dimension 3.2 x 2.9 x 0.8” (90 x 49 x 20 mm) 5 x 3 x 0.9” (132 x 79 x 24 mm) Operating temperature +14°...
System Specifications Camera monitor Operating voltage 5 V DC @ 1 Amp Power consumption 650 mA max Low light solution 12 IR LEDs, 1 Low light sensor Low light sensitivity 1-8 lux Picture sensor OV7725 1/4’ Color CMOS Lens F3.6mm H:53 V:40 Lithium-Polymer Battery Warning This equipment contains a rechargeable lithium-polymer battery.
If you are unable to locate proper recycling facilities in your area, please return this product to Uniden for • recycling. FCC Compliance Information Part 15 Compliance statement This device complies with Part 15 of the FCC Rules. Operation is subjected to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Important: evidence of original purchase is required for warranty service. WARRANTOR: Uniden America Corporation (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants, for three years, to the original retail owner, this Uniden Product to be free from defects in materials & craftsmanship with only the limitations or exclusions set out below.
Need help?
Do you have a question about the Lullaboo G403 and is the answer not in the manual?
Questions and answers