Advertisement
Troubleshooting
If the grill fails
to light:
[]
[]
[]
[]
[]
[]
1,
2,
3.
Turn gas off at source and turn control
knobs
to "OFF". Wait at least 5 minutes
for gas to
clear, and then
retry
If your grill still fails to light,
check the gas
supply
and connections.
Ensure
gas supply
is turned
on (turn
counterclockwise),
there
is gas in the tank,
and the regulator
is
properly
seated
in the tank
valve.
Repeat lighting
procedure.
If your
grill still
fails to light,
turn the gas off at the source,
turn the control
knobs to "OFF", and check
the following:
Obstruction
in Gas Line
Correction:
Detach
regulator
hose assembly.
Do not smoke!
Open all control
knobs at the
same time
to "High".
Close all burner
control
knobs to "OFF" and reattach
the regulator
hose
assembly
to the grill.
Plugged
Orifice
or Burner
Tube Obstruction
Correction:
Remove
burners
from
grill and
clean following
the burner
cleaning
instructions
later
in this manual.
Observe
valve orifice
to be
sure there
is no obstruction
visible.
Ifan obstruction
is suspected
in Gas Valve or
Manifold,
call the Customer
Support
Center.
Hisalignment
of Igniter
and Burner
Correction:
Check for proper
position
of the
electrode
tip. The gap between
the electrode
tip
and burner
should
be approximately
3/16
of an
inch. Adjust
if necessary.
With the gas supply
off
and all control
knobs set to "OFF" press the
electric
igniter
button
and check for the
presence
of a spark
at the electrode.
Disconnected
Electric
Wires
Correction:
Inspect
the electric
igniter
(see
Parts List) found
behind
the control
panel.
Connect
loose electric
wires to ignition
assembly.
Weak AA Battery
Correction:
Unscrew
the igniter
cap and replace
the battery.
Do not dispose
of batteries
in fire!
Batteries
ma'
explode
or leak.
[]
If the grill still does not light you may need to
reset the flow limiting
valve
in your
LP tank.
Note:
This procedure
should
be done every
time a new LP gas tank
is connected
to your
grill.
Follow
the steps
below
to reset
the flow
limiting
device,
[]
Turn LP gas tank
valve "OFF".
[]
Disconnect
the regulator
assembly
from
LP
Gas tank.
[]
Open all burner
control
knobs
to
"HI/LIGHT"
at the same time.
[]
Close all burner
control
knobs to "OFF"
[]
Let the LP Gas tank stand
for at least 10
minutes.
[]
Reconnect
the regulator
assembly
to the LP
Gas tank.
[]
Slowly
turn on the LP Gas tank valve.
[]
Follow the burner
lighting
procedures
to
light the burner
farthest
away from the gas
source.
Should
a FLASHBACK
fire occur in or around
the burner
tubes,
follow
the instructions
below.
Failure to comply
with these
instructions
could result
in a fire or explosion
that could cause serious
bodily
injury,
death,
or property
damage.
• Shut off gas supply
(turn
the LP tank valve
clockwise)
to the gas grill.
• Turn the control
knobs to the "OFF" position.
• Open the grill lid.
Put out any flame
with a Class B Fire
extinguisher
• Once the grill has cooled
down,
clean the
burner
tubes
and burners
according
to the
cleaning
instructions
in this Operator's
Manual.
Customer
Support
Center
Call 8:30
AM to 5:00
pIv] CST 1-800-933-0527
Monday
through
Friday,
25
Advertisement
