1. Manuals
  2. Brands
  3. Ovislink Manuals
  4. Gateway
  5. IWE3200-H
  6. User manual

Ovislink IWE3200-H User Manual

Hotspot gateway
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
IWE3200-H
HotSpot Gateway
User's Guide
Version: 1.0
Last Updated: 08/11/2006

Advertisement

Table of Contents
loading

Related Manuals for Ovislink IWE3200-H

Summary of Contents for Ovislink IWE3200-H

  • Page 1 IWE3200-H HotSpot Gateway User’s Guide Version: 1.0 Last Updated: 08/11/2006...
  • Page 2 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 3 R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 9 March 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Termi- nal Equipment and Satellite Earth Station Equipment) as of April 8, 2000.

  • Page 4: Table Of Contents

    Table of Contents 1. Introduction ......................... 1 1.1. Overview........................1 1.2. Features........................2 1.3. LED Definition......................7 1.4. Feature Comparison ....................7 2. First-Time Installation and Configuration ................8 2.1. Selecting a Power Supply Method................8 2.2. Mounting the IWE3200-H on a Wall ................. 9 2.3.
  • Page 5 2.13.2. RADIUS ...................... 55 2.13.3. Authentication Session Control ..............57 2.13.4. Authentication Page Customization............57 2.14. DDNS........................59 2.15. Configuring Advanced Settings ................60 2.15.1. Filters and Firewall ..................60 2.15.2. Management....................62 2.15.3. LAN Device Management................64 Appendix A..........................66 A-1: Default Settings......................

  • Page 6: Introduction

    1. Introduction 1.1. Overview Wireless HotSpot Gateway enables Telco operators, wireless ISPs, enterprises, IWE3200-H government institutes, or school campuses to deploy WLANs with secured user authentication support. It generates the user log on/off information for back-end billing systems, and user access log status for tracking purpose, which is very useful and demanded function for the environment requires highly security deployment, such as government institute, bank, or military campus.

  • Page 7: Features

    1.2. Features User Authentication, Authorization, and Accounting Web redirection. When an unauthenticated wireless user is trying to access a Web page, he/she is redirected to a logon page for entering the user name and password. Then, the user credential information is sent to a back-end RADIUS server for authentication. Local pages or external pages.
  • Page 8 Enabling/disabling SSID broadcasts. The user can enable or disable the SSID broadcasts functionality for security reasons. When the SSID broadcasts functionality is disabled, a client computer cannot associate the wireless AP with an “any” network name (SSID, Service Set ID); the correct SSID has to be specified on client com- puters.
  • Page 9 NAT server. Client computers can share a public IP address provided by an ISP (Internet Service Provider) by NAT (Network Address Translation). And our NAT server function- ality supports the following: Virtual server. Exposing servers on the intranet to the Internet. PPTP, IPSec, and L2TP passthrough.
  • Page 10 Wireless-to-Ethernet-LAN traffic blocking. Traffic between the wireless interface and the Ethernet LAN interface can be blocked. Changeable MAC Address of the Ethernet WAN Interface. Some ADSL modems work only with Ethernet cards provided by the ISP. If IWE3200-H is used in such an environment, the MAC address of the WAN interface of the Router has to be changed to the MAC address of the ISP-provided Ethernet network card.
  • Page 11 In addition, it can also be configured to accept management commands only from specific hosts. UPnP. The access Router responds to UPnP discovery messages so that a Windows XP user can locate the access Router in My Network Places and use a Web browser to config- ure it.

  • Page 12: Led Definition

    1.3. LED Definition : Power : Alive. Blinks when the IWE3200-H is working normally. : IEEE 802.11b/g interface activity : Ethernet WAN/LAN interface activity WAN/LAN Fig. 1. LED Indicator. 1.4. Feature Comparison IWE3200-H0S36X IWE3200-H9S36X Wired Advanced Wireless Advanced IEEE 802.11 AP functionality ■...

  • Page 13: First-Time Installation And Configuration

    2. First-Time Installation and Configuration 2.1. Selecting a Power Supply Method The IWE3200-H can be powered by either the supplied AC power adapter or the optional IWE500-INJ POE Power Injector. The IWE3200-H automatically selects the suitable power de- pending on your decision. To power the IWE3200-H by the supplied power adapter: Plug the power adapter to an AC socket.

  • Page 14: Mounting The Iwe3200-H On A Wall

    Fig. 4. Connecting Ethernet cables to IWE500-INJ. Check the “ACTIVE” LED: if power is successfully fed into the IWE3200-H, the “ACTIVE” LED will be on (Red light); otherwise, the “ACTIVE” LED will be off. If the electricity current is over the normal condition (Io＞1.0 A), the “ACTIVE” LED will flash (Red light).

  • Page 15: Preparing For Configuration

    2.3. Preparing for Configuration To configure a IWE3200-H, a managing computer with a Web browser is needed. For first-time con- figuration of a IWE3200-H, an Ethernet network interface card (NIC) should have been installed in the managing computer. For maintenance-configuration of a deployed IWE3200-H, either a wireless computer or a wired computer can be employed as the managing computer.

  • Page 16: Changing The Tcp/Ip Settings Of The Managing Computer

    2.3.2. Changing the TCP/IP Settings of the Managing Computer Use the Windows Network Control Panel Applet to change the TCP/IP settings of the managing computer, so that the IP address of the computer and the IP address of the IWE3200-H are in the same IP subnet.

  • Page 17: Setup Wizard Step 1: Selecting An Operational Mode

    On the Home page, click the SETUP WIZARD to quickly change the configuration of the gateway. Fig. 8. The Home Page. 2.4.2. SETUP WIZARD Step 1: Selecting an Operational Mode Fig. 9. Operational modes.

  • Page 18: Setup Wizard Step 2: Configuring Tcp/Ip Settings

    2.4.3. SETUP WIZARD Step 2: Configuring TCP/IP Settings 2.4.3.1. Router with a PPPoE-Based DSL/Cable Connec- tion Fig. 10. TCP/IP settings for Router with a PPPoE-Based DSL/Cable Connection mode. In this mode, two IP addresses are needed—one for the Ethernet LAN interface and the other for the WAN interface.
  • Page 19 The default LAN IP address is 192.168.0.1 and the default subnet mask is 255.255.255.0. In most cases, these default settings need no change. As for the WAN IP address, it is obtained by DHCP from the ISP. The Trigger mode setting affects the behavior of the DHCP client of the Router.

  • Page 20: Setup Wizard Step 3: Dhcp Server Settings

    Fig. 13. TCP/IP settings for Router with Multiple DSL/Cable Connections mode. Since the Internet connection can be PPPoE-based, DHCP-based, or Static-IP-based, the addressing settings of each WAN interface are the same as those of Router with a PPPoE-Based DSL/Cable Connection, DHCP-Based DSL/Cable Connection, or Router with a Static-IP DSL/Cable Con- nection, respectively.

  • Page 21: Configuring User Authentication Settings

    puter and the SSID of the wireless access Router must be identical for them to communicate with each other. 2.4.6. Configuring User Authentication Settings The IWE3200-H supports both Web redirection-based and non-802.1x-based user and IEEE 802.1x-based user authentication. After the IP addressing settings have been set using SETUP WIZARD, you have to configure Web redirection settings and/or IEEE 802.1x settings for wireless user authentication.

  • Page 22: Local Authentication Sever

    1.3.2. 1.3.3. CHAP 2. Enable without Authentication – Enable only the Web-Redirection, but disable the user Authenti- cation mechanism. User will automatically redirect to the destination web page if the URL indi- cated. Fig. 18. Web redirection settings – Enable without Authentication 3.
  • Page 23 Internet , which is used with the input unit by the control keypad. For example, if the per unit time is 50 (min) and the control keypad is input to be 5 (units), then the total available access time frame of the user is 50 x 5 = 250 (min). Default is ‘1’ min. Valid period (hour): to define the valid period (by hour) while the user account generated.
  • Page 24 Inactive: to show the user account that access time frame expired, or ‘Valid Period’ ex- pired. Permanent: to show the user account that would never expire. The state for the user ac- counts which created by manual would be permanent. This kind of account would not have any information for the session time and cost Fig.

  • Page 25: Configuring Radius Settings

    defined Fig 24 of Sec.2.4.7.2. 2.4.6.4. IEEE 802.1x Fig. 23. Changing security mode to an IEEE 802.1x option. To setup IEEE 802.1x-based user authentication, go to WIRELESS Communication Security section, and then change the Security mode setting to an IEEE 802.1x-related option according to your needs.

  • Page 26: Deploying The Iwe3200-H

    Web Redirection ■ ■ ■ Disabled Table 1. Allowable authentication modes. 2.5. Deploying the IWE3200-H After the settings have been configured, deploy the Router to the field application environment. You have to connect AP(s), modem(s), and RADIUS server(s) to the IWE3200-H. The system configura- tion in Fig.

  • Page 27: Setting Up Client Computers

    formation). The IWE3200-H supports the built-in user database for local authentication, this function also associ- ates the optional external mini-POS Ticket Printer for billing printing purpose. The setup scenario is shown in Fig 28. Please also refer to Sec. 2.4.7.3 for detail operation instruction of mini-POS, keypad, and ticket printing.

  • Page 28: Configuring Tcp/Ip-Related Settings

    Both the wireless client computer and the deployed APs must have the same WEP settings for them to communicate with each other. Therefore, unless IEEE 802.1x EAP-TLS, which supports dynamic WEP key distribution, is used, it’s strongly suggested not to enable WEP functionality of the deployed APs for hotspot applications.
  • Page 29 Fig. 28. User name and password for authentication. If the user name and password are correct. Now you’ll be brought to the original page you have requested after waiting for a few seconds. Meanwhile, a window for log-off and session status appears.

  • Page 30: Using Web-Based Network Management

    If you complete the above procedure without error, the Router together with the RADIUS server has been correctly set up for Web redirection-based authentication. 2.8. Using Web-Based Network Management Fig. 32. The Home page. 2.8.1. Menu Structure The left side of the start page contains a menu for you to carry out commands. Here is a brief descrip- tion of the hyperlinks on the menu: Home.
  • Page 31 TCP/IP. TCP/IP-related settings. Address. IP addressing settings for the Router to work in the TCP/IP networking world, or user name and password provided by the ISP. DNS. DNS (Domain Name System) proxy settings. NAT. Settings for the NAT (Network Address Translation) server on the Router. DHCP Server.

  • Page 32: Save, Save & Restart, And Cancel Commands

    Access Rules. Settings for the time frame policy to Permit/Deny administrator to access the IWE3200-H. LAN Device Management. Settings for the Router to know what LAN devices it has to manage. Status. System monitoring information. Associated Wireless Clients. Display the status of all wireless clients who associated to IWE3200-H.

  • Page 33: Seeing Status

    At the bottom of each status page that shows read-only information, there are two buttons—Home and Refresh. Clicking Home brings you back to the start page. Clicking Refresh updates the shown status information. 2.9. Seeing Status 2.9.1. Associated Wireless Clients Fig.

  • Page 34: Account Table

    Any authenticated user can be terminated by clicking the corresponding Terminate link so that this user is blocked from using networking services provided by the Router. A terminated user is moved to the Terminated Users Table. Clicking the corresponding Release link puts a terminated user back into authenticated state.

  • Page 35: Managed Lan Devices

    Fig. 41. Latest incoming user traffic sessions. On this page, latest 50 outgoing and 50 incoming user traffic sessions are shown for monitoring net- work activity. 2.9.5. Managed LAN Devices Fig. 42. Managed LAN devices. On this page, the status of every managed LAN device is shown. The Offline status indicates a non- working device while the Online status indicates a working device.
  • Page 36 Fig. 43. Operational modes. On this page, you can specify the operational mode for the Router. Currently, 5 modes are available: Router with a PPPoE-based DSL/Cable Connection. In this mode, the Router assumes that a DSL or cable modem is connected to its Ethernet WAN interface. The client computers can therefore share this DSL/cable-based Internet connection by the NAT server functionality.

  • Page 37: Changing Password

    2.10.2. Changing Password Fig. 45. Password. On this page, you could change the user name and password of the administrator. The administrator can view and modify the configuration of the IWE3200-H. The new password must be typed twice for confirmation. 2.10.3.

  • Page 38: Upgrading Firmware By Tftp

    Fig. 48. Configuration backup by HTTP. To back up configuration of the access Router by HTTP: Click Back Up. You’ll be prompted to open or save the configuration file. Click Save. The configuration file is named by the IWE3200-H’s MAC address. For example, if the IWE3200-H’s MAC address is 00-01-02-33-44-55, the configuration backup file should be “000102334455.hex”.
  • Page 39 Fig. 51. Firmware upgrade by TFTP. To upgrade firmware of the access Router by TFTP: Get a computer that will be used as a TFTP server and as a managing computer to trigger the upgrade process. Connect the computer and one of the LAN Ethernet switch port with a normal Ethernet cable. Configure IP address of the computer so that the Router and the computer are in the same IP subnet.
  • Page 40 net. In this case, you must have configured the Router to be remotely manageable (see Section 2.13.1.1) and adjust the Timeout and Max no. of retries settings of TFTP Server for remote TFTP upgrade to succeed. 2.10.3.4. Backing up and Restoring Configuration Set- tings by TFTP Fig.

  • Page 41: Setting Time Zone

    example, if the Router’s MAC address is 00-01-02-33-44-55, the configuration backup file should be “000102334455.hex”. On the computer, run a Web browser and click the General, Firmware Tools hyperlink. Within the Configuration Backup/Restore section, specify the IP address of the computer, which acts as a TFTP server.
  • Page 42 2.11.1.1. Router with a PPPoE-Based DSL/Cable Con- nection Fig. 56. TCP/IP settings for Router with a PPPoE-Based DSL/Cable Connection mode. If the IWE3200-H was set to be in Router with a PPPoE-Based DSL/Cable Connection mode, two IP addresses are needed—one for the Ethernet LAN interface and the other for the WAN interface. The LAN IP address must be set manually to a private IP address, say 192.168.0.xxx.
  • Page 43 Fig. 57. TCP/IP settings for Router with a DHCP-Based DSL/Cable Connection mode. If the IWE3200-H was set to be in Router with a DHCP-Based DSL/Cable Connection mode, two IP addresses are needed—one for the Ethernet LAN interface and the other for the WAN interface. The LAN IP address must be set manually to a private IP address, say 192.168.0.xxx.

  • Page 44: Dns

    2.11.1.4. Router with Multiple DSL/Cable Connections Fig. 59. TCP/IP settings for Router with Multiple DSL/Cable Connections mode. Since the Internet connection can be PPPoE-based, DHCP-based, or Static-IP-based, the addressing settings of each WAN interface are the same as those of Router with a PPPoE-Based DSL/Cable Connection, DHCP-Based DSL/Cable Connection, or Router with a Static-IP DSL/Cable Con- nection, respectively.

  • Page 45: Nat

    2.11.2.2. Static DNS Mappings Fig. 61. Static DNS mappings. By Static DNS Mappings, an internal server can be given a domain name, so that other hosts on the intranet can access the server by its domain name instead of by its IP address. For example, an inter- nal Web server for the intranet, say 192.168.0.2, may be associated with the domain name, www.company-name.com.

  • Page 46: Dhcp Server

    2.11.3.2. Virtual Server Mappings Fig. 63. Virtual server mappings. The gateway enables you to expose internal servers on the intranet through NAT to the Internet for public use. The exposed internal servers are called virtual servers because from perspective of hosts on the Internet, these servers are invisible in terms of TCP/IP.

  • Page 47: Static Dhcp Mappings

    2.11.4.2. Basic Fig. 64. Basic DHCP server settings. The Router can automatically assign IP addresses to client computers by DHCP. In this section of the management page, you can specify the Default Router, Subnet mask, Primary DNS server, and Secondary DNS server settings that will be sent to a client at its request. Additionally, you can spec- ify the first IP address that will be assigned to the clients and the number of allocateable IP addresses.

  • Page 48: Load Balancing

    To always assign a static IP address to a specific DHCP client: Specify the MAC address of the DHCP client and the IP address to be assigned to it. Then, give a description for this mapping. Select the corresponding Enabled check box. 2.11.5.

  • Page 49: Zero Client Reconfiguration

    2.11.6. Zero Client Reconfiguration Fig. 68. Zero Client Reconfiguration Settings. The IWE3200-H provides the ‘Zero Client Reconfiguration’ function to allow the wireless clients associate to the IWE3200-H without any network setting modification required. It is convenient func- tion for the wireless users who can associate the IWE3200-H automatically and no need to learn the network environment detail where the IWE3200-H deployed.

  • Page 50: Wireless Distribution System

    Since the IEEE 802.11g-based IWE3200-H is also IEEE 802.11b compatible, you can configure the Date rate setting to meet your backwards compatibility needs. If there is RF interference, you may want to reduce the Data rate for more reliable wireless transmission. In most cases, leave the setting to Auto.
  • Page 51 Fig. 71. Wireless Distribution System settings. To enable a WDS link: Specify the MAC address of the AP or wireless bridge at the other end of the WDS link. Select the corresponding Enabled check box. For example, assume you want a wireless access Router and an AP with MAC addresses 00-02-65-01-62-C5 and 00-02-65-01-62-C6, respectively, to establish a WDS link between them.

  • Page 52: Security

    2.12.2. Security IEEE 802.11b/g security settings include SSID broadcasts, Security mode, IEEE 802.11 Authenti- cation algorithm, WEP keys, MAC-Address-Based Access Control. 2.12.2.1. Basic Fig. 74. Basic IEEE 802.11g security settings. For security reasons, it’s highly recommended that the security mode be set to options other than Open System.
  • Page 53 Fig. 76. Behavior of the “All APs on This Subnet” wireless client isolation option. As illustrated in Fig. when AP 1 and AP 2 are using the “This AP Only” option, wireless traffic be- tween STA 1 and STA 2 is blocked by AP 1, while wireless traffic between STA 2 and STA 3, which are associated with different APs, is still allowed.
  • Page 54 In the above security modes, a back-end RADIUS (Remote Authentication Dial-In User Service) server is needed if IEEE 802.1x functionality is enabled. See Section 2.13.2 for more information about IEEE 802.1x and RADIUS. According to the IEEE 802.11 standard, WEP can be used for authentication and data encryption. Normally, Shared Key authentication is used if WEP data encryption is enabled.
  • Page 55 Specify the MAC address of a wireless client to allow access, and then click Add. Repeat Step 3 for each other wireless client. To delete an entry in the access control table: Click Delete next to the entry. The size of the access control table is 64. NOTE: Fig.

  • Page 56: Configuring Aaa (Authentication, Authorization, Accounting) Settings

    2.13. Configuring AAA (Authentication, Authorization, Ac- Settings counting) 2.13.1. Web Redirection The IWE3200-H supports both IEEE 802.1x-based and Web redirection-based user authentication. Here is a brief description of how Web redirection works: When an unauthenticated wireless user is trying to access a Web page, a logon page is shown instead of the requested page, so that the user can type his/her user name and password for authentication.
  • Page 57 2.13.1.1. Basic Fig. 81. Web redirection enabled with authentication. There are three modes for Web redirection—Enabled with Authentication, Enabled without Au- thentication, and Disabled. In Enabled with Authentication mode, you specify the RADIUS authentication method that cor- responds to your RADIUS server settings. Currently EAP-MD5, PAP, and CHAP are supported. When a wireless user tries to access the Internet, he/she is redirected to a Default log-on page or a page stored on an external Web server (The following URL), depending on the network administra- tor’s choice.

  • Page 58: Unrestricted Clients

    Fig. 83. Default log-off page. On a PDA such as Pocket PC, the log-off would not be shown. To log off from the net- NOTE: work, go back to the log-on page, and then click Log Off to end the session. If the user fails the authentication, the user can be brought to a default warning page (Default page) or a page for the user to subscribe a wireless Internet access service (The following URL).

  • Page 59: Walled Garden

    There are occasions on which you want some computers to be able to freely access the Internet with- out being authenticated first. For example, you may want your wired desktop computers connected with the Router to be uncontrolled by the Router while providing wireless Internet access service for your customers with wireless laptop computers.

  • Page 60: Radius

    2.13.2. RADIUS IEEE 802.1x Port-Based Network Access Control is a standard for solving some security issues asso- ciated with IEEE 802.11, such as lack of user-based authentication and dynamic encryption key dis- tribution. With IEEE 802.1x, a RADIUS (Remote Authentication Dial-In User Service) server, and a user account database, an enterprise or ISP (Internet Service Provider) can manage its mobile users’...
  • Page 61 2.13.2.1. Basic Fig. 89. RADIUS basic settings. For the IWE3200-H, the RADIUS client component of the Router is shared by the IEEE 802.1x and Web redirection components. The RADIUS settings are for the RADIUS client to communicate with backend RADIUS servers. The RADIUS server do not support all combinations of authentication methods if both IEEE 802.1x and Web redirection are enabled.

  • Page 62: Authentication Session Control

    2.13.3. Authentication Session Control Fig. 91. Authentication session control settings. Authentication session control settings are for controlling the lifetimes of user authentication sessions. The Idle timeout setting specifies how long a user can be idle without generating any traffic before being terminated.
  • Page 63 Fig. 93. Authentication success page customization settings. Fig. 94. Authentication failure page customization settings. In addition to the Text alignment, HTML title, and Contents setting, two more settings are provided for specifying the size of the Log-Off window (Windows width and Window height). Fig.

  • Page 64: Ddns

    Fig. 96. Advertisement links settings. Fig. 97. Advertisement links in action. 2.14. DDNS Fig. 98. Dynamic DNS settings. With the help of dynamic DNS (DDNS) services provided by dyndns.org or no-ip.com, you can make your device automatically register the IP address it obtains dynamically by PPPoE or DHCP with the DDNS servers.

  • Page 65: Configuring Advanced Settings

    2.15. Configuring Advanced Settings 2.15.1. Filters and Firewall 2.15.1.1. Packet Filters Fig. 99. Packet filters settings. You can specify rules for the firewall component of the Router to check outgoing packets. Packets that meet the rules can be permitted or denied. The protocol field, source IP address field, destination IP address field, and destination port field of a packet’s IP header are inspected to see if it meets a rule.

  • Page 66: Url Filters

    Set the rules with great care since incorrect rules would make the Router inaccessible. The last resort to restore the Router to service may be resetting its configuration to fac- NOTE: tory-set values by pressing the Default switch on the housing of the Router. 2.15.1.2.

  • Page 67: Management

    The IWE3200-H is capable of blocking HTTP traffic from the intranet to specified unwelcome Web sites. To block HTTP traffic to an unwelcome Web site: Specify the URL (ex. www.xxx.com) of the unwelcome Web site. Select the corresponding Enabled check box. Do not type “http://”...

  • Page 68: System Log

    UPnP (Universal Plug and Play) enables a Windows XP user to automatically discover peripheral de- vices by HTTP. When the UPnP functionality is enabled, you can see the Router in My Network Places of Windows XP. The Router can be given a friend name that will be shown in My Network Places.

  • Page 69: Lan Device Management

    2.15.2.4. SNMP Fig. 106. SNMP settings. The IWE3200-H can be managed by SNMP (Simple Network Management Protocol), and the SNMP management functionality can be disabled. You can specify the name (used as a password) of the read-only and read-write community. In addition, up to 5 SNMP trap targets can be set in the SNMP Trap table.
  • Page 70 A management server from the Internet sees a managed LAN device as a combination of the access Router’s WAN IP address and a Virtual Port reserved for this device. When a TCP or UDP-based management request (specified by the Protocol field) is received by the access Router from the Inter- net, the IWE3200-H translates the destination IP address and destination port of the request to the corresponding Device IP Address and Device Port.

  • Page 71: Appendix A

    Appendix A A-1: Default Settings Press the Default switch on the housing of a powered-on Router to reset the configura- TIP: tion settings to factory-set values. Setting Name Default Value Global User Name root Password root Operational Mode Gateway with a Static-IP DSL/Cable Connection WAN Interface Type...

  • Page 72: A-2: Led Definitions

    DNS Proxy Static DNS Mappings Not set Filters/Firewall Packet Filters Not set URL Filters Not set VLAN Disabled WAN ICMP Request Blocking Disabled State Packet Inspection (SPI) Disabled Authentication Web Redirection Disabled RADIUS Not set RADIUS Robustness Reboot User reboot Name Session Control Disabled...

  • Page 73: Appendix B: Troubleshooting

    Appendix B: Troubleshooting Check the following first: Make sure that the power of the Router is on and the Ethernet cables are connected firmly to the RJ-45 jacks of the Router. Make sure that the LED ALV of the Router is blinking to indicate the Router is working. Make sure the types of the Ethernet cables are correct.
  • Page 74 Solve the following problems in order: The wireless client cannot pass Web redirection-based authentication. Are user name and password are correct? Check the user credential information stored on the RADIUS server. Is the RADIUS server correctly set up? Check whether the password for the wireless client is stored using reversible encryp- tion on the RADIUS server.

  • Page 75: B-2: Wireless Settings Problems

    Find out the answer on the start page of the Web-Based Network Manager. Is the NAT server functionality of the IWE3200-H enabled? Find out the answer on the start page of the Web-Based Network Manager. If you cannot find any incorrect settings of the IWE3200-H, the default Router of the IWE3200-H may be really down or there are other communication problems on the net- work backbone.

  • Page 76: B-3: Other Problems

    B-3: Other Problems I forget the IP address of the LAN interface of the IWE3200-H. What can I do to connect to it using a Web browser? My IWE3200-H has been set to obtain an IP address automatically by DHCP. How can I know its acquired IP address so that I can manage it using a Web browser? Wireless Gateway/AP Browser (WLBrwsr.exe) in the “Utilities”...

  • Page 77: Appendix C: Technical Specifications

    Appendix C: Technical Specifications C-1: IWE3200-H Standards: 802.11b 802.11g 802.3 802.3u 802.3af Data rate & modulation: OFDM@54Mbps, CCK@11/5.5Mbps, DQPSK@2Mbps and DBSK@1Mbps Radio Technology: OFDM DSSS Operating Range: Up to 1,155 feet Channels: USA: 1-11 (FCC), Canada: 1-11 (IC), Europe: 1-13 (ETSI), Japan: 1-14 Frequency range: 2.402 ~ 2.472 GHz (North America)
  • Page 78 Interface: 10/100 Mbps RJ-45 Connector RS-232c Serial Connector 802.11b/g WLAN Security: 64/128-bit WEP 802.1x MAC address filtering Disabled SSID broadcast Wireless client isolation Configuration and Management: Web-browser TFTP SNMP Syslog Event Logging LEDs: Power LAN/WAN WLAN Alive Environmental: Temperature: Operating (0~55C), storage (-20~70C) Humidity: 5% to 95% non-condensing in storage Electromagnetic Compatibility: FCC Class B...

  • Page 79: C-2: Iwe500-Inj Power Injector

    C-2: IWE500-INJ Power Injector Input Power Requirements AC Input Voltage : 90 – 264Vac AC Frequency : 47 – 63 Hz AC Input Current : 2A at 100Vac, 1A at 240Vac, (-48Vdc) Power over LAN output Specification Pin Assignments and Polarity: (＋) 4/5 (－) 7/8 Output Voltage : Aggregate Power:50W (48Vdc)

  • Page 80: C-3: Iwe810-Pos Mini-Pos Ticket Printer

    C-3: IWE810-POS mini-POS Ticket Printer Printing Method Direct Thermal Printing Speed 150 mm/sec (5.905 inch/sec) Dot Density 180 x 180 DPI Dot Pitch 0.141 mm, 0.125 mm Effective Printing Width 72mm, 552 dots/line - Font A : 46 columns Character Per Line - Font B : 61 columns - Korea : 21 columns Paper Type...

Table of Contents