EarthQuake Cinénova IR16 User Manual

EarthQuake Cinénova IR16 User Manual

8-zones multi-source ir driven amplifier

Advertisement

Quick Links

Cinénova 16
IR
8-ZONES MULTI-SOURCE
IR DRIVEN AMPLIFIER
USER'S MANUAL
Earthquake Sound Corporation
2727 McCone Avenue. Hayward, CA 94545
Phone: 510-732-1000
Fax: 510-732-1095
www.earthquakesound.com
Sound That Will Move You.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Cinénova IR16 and is the answer not in the manual?

Questions and answers

Summary of Contents for EarthQuake Cinénova IR16

  • Page 1 Cinénova 16 8-ZONES MULTI-SOURCE IR DRIVEN AMPLIFIER USER’S MANUAL Earthquake Sound Corporation 2727 McCone Avenue. Hayward, CA 94545 Phone: 510-732-1000 Fax: 510-732-1095 www.earthquakesound.com Sound That Will Move You.
  • Page 3: Table Of Contents

    én ova-IR16 Power Amplifier Table of Content Getting Started Safety Instructions ........4 - 5 Introduction .
  • Page 4: Safety Instructions

    © 2008 Earthquake Sound Corporation. All rights reserved. This document should not be construed as a commitment on the part of Earthquake Sound Corporation. The information is subject to change without notice. Earthquake Sound Corporation assumes no responsibility for errors that may appear within this document.
  • Page 5: Safety Instructions

    én ova-IR16 Power Amplifier Safety Instructions Important Safety Instructions 1) Read these instructions in their entirety. 10) Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the pint 2) Store this manual and packaging in a safe place. where they exit from the apparatus.
  • Page 6: Introduction

    About Cinénova-IR16 The Cinénova-IR16 is the second generation in multi-zone that Earthquake has produced. Thanks to the feedbacks received from custom home installers worldwide, we have managed present you with a truly powerful yet audiophile multi-zone amplifier with the following features:...
  • Page 7: Unpacking

    It is best to use a grounded electrical outlet to power the amplifier. Lack of input ground reference could be unsafe. There are several factors to consider before installing the Earthquake Consult with your electrical contractor about proper grounding. Sound Cinénova-IR16 system.
  • Page 8: Front & Rear Panel Overview

    Front & Rear Panel Overview Earthquake Sound 19” (482.6mm) Cinénova C to C 18.375” (466.5mm) 17” (431mm) SPEAKER OUTPUT FUSE 110-120VAC-60Hz 220-240VAC-50Hz...
  • Page 9: Front Panel Map

    én ova-IR16 Power Amplifier Front Panel Map Front Panel Cinénova Power/Standby Switch This red colored LED indicates whether the amplifier is ON or OFF. When the amplifier is ON, this LED will be lit. Note: When using the rear 12V DC Trigger (page 11 - feature 11), this front switch must be turned OFF. Front Panel Power LED This LED reflects the power status of the whole amplifier.
  • Page 10: Rear Panel Map - Local

    24 to 12 AWG. We recommend using the CAT5, CAT5E, CAT6 or CAT6E wires. IR IN – receive all types of IR signal transmitted through the Earthquake Keypad. It allows Volume up/down and mute function at the local amplifier. Also, it allows most IR signal to pass through the four built-in IR repeaters of the Cinénova 16IR (page 11 - feature 12).
  • Page 11: Rear Panel Map - Bus

    IR Outputs IR OUT Four (4) amplified IR repeaters to repeat signals and commends fed through individual Earthquake Keypads. Power Connection This three (3) prong AC line connector is factory preset to 120VAC. However, other voltages are also available.
  • Page 12: Keypad & Remote Map

    VOL+ VOL- In addition to the eight (8) Earthquake Keypads, we also provide you with remote controls that have the same functions – Volume Up/Down and Mute. For your convenience, the remote information can be taught to any remote with learning capability.
  • Page 13: Special Features

    The Cinénova-IR16 is factory preset to 110-120VAC. However, front panel. They show the operating status of each channel; the LEDs it can also be set to accommodate 220-240VAC by Earthquake will illuminate when the maximum recommended output is exceeded. authorized technician(s)/dealer(s).
  • Page 14: Features Explained

    Features Explained Earthquake Sound SPEAKER OUTPUT FUSE 110-120VAC-60Hz 220-240VAC-50Hz Amplifier section Explained BUS section Explained Rear Gain Control Limiter (RGCL) It controls the front pad maximum output power from over Bus Control Limiter (BCL) powering small speakers. The module RGCL will limit the...
  • Page 15: Ir Wiring Configuration Sample

    én ova-IR16 Power Amplifier IR Wiring Configuration Sample The Cinénova 16 IR allows you to connect several sources to the input stage of the amplfier. It also allows you to aim the remote at the zone pad and use the source remote control. As you aim the remote to the pad, the IR signal is transmitted from the pad to the amplifier and thereafter amplified.
  • Page 16: Recommended Configuration

    Recommended Configuration Earthquake Sound SPEAKER OUTPUT FUSE 110-120VAC-60Hz 220-240VAC-50Hz 150 Watts RMS/Per Channel 75 Watts RMS/Per Channel 1-High Power Zones Background room(s) MONO/Bridged 6-Zones STEREO...
  • Page 17: Specifications

    én ova-IR16 Power Amplifier Specifications SPECIFICATIONS • Number of channels 16 Channels • Dimensions Face plate (W x D x H): 19” (482.6mm) x 0.47” (12mm) x 6.87” (174.5mm) • Power rating per channel Mounting (W x H): 18.37” (466.5mm) x 4” (101.5mm) (4-Ohm stereo), all channels driven: 75 Watts RMS Chassis (W x D x H):...
  • Page 18: Troubleshooting & Maintenance

    If the amp turns on then the problem is with your home circuit breaker. If the amplifier still does not power up, please call Earthquake to consult with a technician. If you are still stuck... Note: 1.
  • Page 19: Product Warranty

    • First year: Earthquake pays for labor, parts, and ground freight (only in US properly filled & returned to Earthquake with a copy of the sales invoice.
  • Page 20 Sound That Will Move You. Earthquake Sound reserves the right to amend details of the specifications without notice Copyright © Earthquake Sound Corporation Earthquake Sound Corporation | 2727 McCone Avenue. Hayward, CA 94545 | Phone: 510-732-1000 Fax: 510-732-1095...

Table of Contents