Download Print this page

Emerson 500VA Quick Start Manual

500va/600va, 120v ups systems

Advertisement

I
S
MPORTANT
AFETY

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during
installation and maintenance of the UPS.
• Intended for installation in a controlled environment.
• Maximum ambient temperature 104°F (40°C).
CAUTION
!
To reduce the risk of fire, connect only to a circuit provided with
20 amperes maximum branch circuit overcurrent protection in
accordance with the national code, ANSI/NFPA 70.
• Do not connect equipment that may overload the UPS or demand half-wave
rectification, such as a laser printer.
S
ETUP
Step 1 Inspect the Package
Inspect the package and the UPS upon receipt. Notify the carrier and dealer of visible
damage.
UPS
Step 2 Decide Where to Place the UPS
The UPS must be placed indoors, protected from water, direct
sunlight and excessive heat.
Provide at least 4" (100mm) of clearance on all sides of the unit
for proper ventilation.
Step 3 Charge the UPS Battery Before
Use
The UPS battery is not charged before shipping. It MUST be charged before use.
• Connect the UPS power cord to a wall outlet and charge for at least eight hours.
Note: If battery is placed in storage, charge the battery every six months if kept at
5°F to 85°F (-15°C to 29°C)—or every three months if kept at 86°F (30°C) or higher.
Step 4 Start the UPS
After the battery is fully charged:
• Turn on the UPS by pressing the On/Off button (see Figure 1 below).
LED 1 should be illuminated (green), indicating the UPS is operating in Normal Mode.
UPS C
ONTROLS AND
Figure 1 - Front Panel LEDs
LED 1
(green)
Utility
symbol
EMERSON
Network Power
UPS Status, Alarm Conditions and Alerts
Condition
Normal Mode
Battery Mode
Battery Low
Overload
Battery Replacement
Fault
Liebert
Quick-Start Guide - 500VA/650VA, 120V
I
NSTRUCTIONS
Liebert
shutdown
software
CD
Quick-start
guide
C
ONNECTIONS
On/Off button
!
Liebert
PSA
®
AC Power System
LED
Color
LED 1
Green
Solid (steady glow)
LED 1
Green
Flashes every 3 seconds
LED 1
Green
Flashes every 1 second till end of discharge (EOD)
LED 2
Amber
Solid (steady glow) until load drops or breaker trips
LED 2
Red
Flashes every 1 second for 5 seconds only
LED 2
Red
Solid (steady glow) until UPS shuts down after 5 seconds
PSA
®
• Connect the UPS only to an earthed / grounded outlet that meets national and local
electrical safety guidelines.
• Locate the UPS near a wall outlet. Do not use an extension cord between the UPS and
the outlet.
• The Liebert PSA has been designed for small office/home office use only; it is NOT
recommended for use in life-support applications.
• In the event of an emergency, press the OFF button and disconnect the power cord
from the AC power supply to properly disable the UPS.
• Do not attach power strips or surge suppressors to the UPS.
• Do not attempt to service any parts inside the UPS except the batteries. Failure to adhere
to this could cause personal injury or equipment malfunction and void the warranty.
• For technical support:
• Visit
www.liebert.com
• Send an e-mail to upstech@emersonnetworkpower.com.
Step 5 Check the Site Wiring Fault Indicator
See figure at right for the location of the Site Wiring Indicator on the rear of
the UPS.
• Check the rear of the UPS to make sure the Site Wiring Fault indicator is
NOT illuminated.
Caution: If the Site Wiring Fault indicator is illuminated, have a qualified
electrician check the wall receptacle wiring and fix any problems.
Step 6 Connect the Loads
The UPS has three battery backup outlets that
provide power when the UPS operates on bat-
tery (see Figure 2 below).
USB
cable
• Plug the loads into the battery backup outlets
on the rear of the UPS.
Caution: Do not connect a laser printer to the
UPS.
Step 7 Connect the Network Surge Protection
The UPS has two RJ-45 jacks for network lines (see
Figure 2 below).
• Connect a single-line network cable into the RJ-45
network surge protection IN jack on the rear of the
UPS.
• Connect an RJ-45 cable from the OUT jack on the
rear of the UPS to a port on a PC or network device
such as a router.
Step 8 Set Up Liebert shutdown software
To start using the Liebert shutdown software:
• Install the Liebert shutdown software. See the software
user manual for installation instructions.
• Connect one end of the USB cable (supplied) to the USB
port on the rear of the UPS. Connect the other end to a
USB port on the computer. See the software user manual
for operating instructions.
Overload
symbol
USB
interface
LED 2 (red = fault;
amber = overload)
Input
Fault
breaker
symbol
Surge outlet (1)
NEMA 5-15R
Solid/Flashing
or
Figure 2 - Rear Panel
Site Wiring
Fault indicator
RJ-45 jacks (2) -
network protection
NEMA
5-15P
Battery backup
outlets (3)
NEMA 5-15R
Audible Alarm
(None)
Every 3 seconds
Every 1 second
Continuous
Every 1 second for 5 seconds only
Continuous until UPS shuts down

Advertisement

loading

Summary of Contents for Emerson 500VA

  • Page 1: Save These Instructions

    Quick-Start Guide - 500VA/650VA, 120V MPORTANT AFETY NSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions that should be followed during installation and maintenance of the UPS. • Intended for installation in a controlled environment. • Maximum ambient temperature 104°F (40°C).
  • Page 2 Dispose of the old battery properly at an appropriate recycling facility. ROUBLESHOOTING If the UPS malfunctions during operation, check the following chart for proper adjustment. For further assistance, please contact your local Emerson Network Power representative. Problem Utility power is normal, but LED 1 is not illuminated.

This manual is also suitable for:

650vaLiebert psa500mt3-120uLiebert psa650mt3-120u