Lightolier 5453 Instructions For Installation

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
his fiXtIIrO
k
intended for installationin acmrdsnca with the National Ebafrisal Code and
IOCA
INSTRUCTION SHEET NO.
!gulations.To assure full mmpliansa with Iosal rndes and regulations, shesk with your local elestrissl
lspestor before installation. To prevent elestrisal shosfr,tum ofi eleatdsity at fuse box before prmeeding.
IS:5453
Retain Iheae instructions for maintenance reference.
1291
INSTRUCTIONS FOR INSTALLATION OF 5453
CAUTION
DO NOT MOUNT
TOP EDGE OF FIXTiJRE CLOSER THAN 6 INCHES TO CEILING.
FOR OCTAGONALOUTLETBOXES
. Position BACKPWTE ASSEMBLY centered over OUTLET BOX with bottom edge of BACKPLATE in fine with bottom of OUTLET SOX. (Fig. 1).
Using all MOUNTING HOLESin BACKPL4TEASSEMBLY, semretowallusingwood stiews,toggleklts, oralternatefasteners (not provided) depending
on WSIImaterial. NOTE BACKPLATE ASSEMBLY should be leveled horizontally and outlet box completely covered before final tightening to wall.
'OR HORIZONTALLY MOUNTED RECTANGULAR GEM OR SWITCHOUTLETBOXES
. Remove COVER PIATE horn BACKPLATE ASSEMBLY aa shown in Fig 3.
:, Position BACKPIATE ASSEMBLY centered over OUTLET BOX with bottom edge of BACKPMTE in line with botiom of OUTLET BOX.(Fig. 2).
. Uaingall MOUNTING HOLES in BACKPIATEASSEMBLY, aecuretowall usingwoodaixews, toggle bolta, oralternatefasteners (not provided) depending
on
wall material.
NOTE BACKPUTE ASSEMBLY should be leveled horizontally and outlet box completely covered before final tightening to wall.
VIRING PROCEDURE
. Pull supply wires through WIREWAY OPENING and make conneofions
Blaak fixture lead (or fixture lead without tramr mark) to black supply Ieact white fixture lead (or fixture lead with tracer mark) to white supply wire.
Uninaulstad wire is a GROUND WIRE and must bernnneciad to agroundkrgtarminal or ground wire in the OUTLET SOX, Use wire nuts (local hardware
item), Push the"splisea into the OUTLET BOX.
!, Raiae, FIXTURE ASSEMBLY and align MOUNTING STUD HOLES and SOCKET HOLES with SOCKETS and MOUNT STUDS on BACKPMTE. Gently
slide FIXTURE ASSEMBLY backwards until the MOUNTING STUDSprotrudethroughthe holesin FIXTUREASSEMBLY,Securein placewith
BAITERY NUTS provided.
CAUTION: MAKE CERTAIN THAT NO WIRES ARE PINCHED BETWEEN THE BACKPlATE ASSEMBLY AND THE FIXTURE ASSEMBLY.
1.From top of fixture, position DIFFUSER DISHES over shsular openings (ss shown in Fig. 4) and gently lower until dishes sit securely in each opening.
i. Cover INSPECTION WINOOW with INSPECTION COVER PLATE and secure with screws (Fig. 4).
i. Install remmmended lamps.
CAUTION MAXIMUM WAllAGE AS MARKED ON FIXTURE MUST NOT BE EXCEEDED. FOR HORIZONTAL MOUNTING ONLY.
Front View
WIREVAAY OPENING
VI'4
------ ~TE
}0
o Oo
:000.:
MOUNTING HOLE ~
WTAGONAL BOx~
L
eACKPIATE ASSEMaLY
ouTLETsox COVERPLATE - -J
\-
=ig. 1
1
- OiRWSER
WIREWAY OPENING>
:0
000;
~:o o
GEM aOX~
~ BACKPlATE ASSEMaLY
1A
w
=
WIREW,AY OPENING
Fig.3
::= V-BA"ERYNUTS