Lightolier Calculite C3MRPA Specification

Calculite
12 5/8"
(321mm)
Page 1 of 2
Non-IC Frame:
Non-IC:
C3LV
C3LV
C3LVE1
14 3/8"
C3LVE1
C3LVE2
(365mm)
C3LVE2
(245mm)
Non-IC AirSeal Frame:
C3ALV
Non-IC AirSeal:
C3ALV
C3ALVE1
C3ALVE1 C3ALVE2
14 3/8"
C3ALVE2 (365mm)
10 1/8"
(257mm)
IC AirSeal Frame:
C3AICLV
11 3/16"
IC AirSeal:
(284mm)
C3ALCLVE1
C3AICLV C3AICLVE1
22 3/8"
(568mm)
Ceiling Cutout: 3 1/2" (130mm) Dia.
For Complete Fixture Order: Trim Kit + Frame-In Kit. Each Sold Separately.
Trim Kit
Spec. Sheet
C3MRPA
Baffle Finish Painted White
C3MRPA WH
Matte White
Matte Black C3MRPA BK
Satin Aluminum NA
Features
1. Trim Kit Baffle/Trim Plate : One piece machined aluminum, sharp details
for clean look. 1 1/4" dia. miniature baffle and built-in aperture shield
minimize and blocks view into fixture. Keyed to lamp support assembly
for true aiming of lamp to prevent incorrect installation of cone. Hinged,
and snaps on for easy tool-less installation. Trim plate in painted white or
anodized satin aluminum. Flangeless trim uses Plaster Trim Ring accessory.
Interchangeable with other 3" Evolution trims.
2. Trim Kit Vertical Adjustment Mechanism: Die-cast aluminum. Built-in
aperture shield blocks view into fixture. Provides 0°- 35° vertical tilt up
to 1" thick ceiling, less in thicker ceilings; lockable 25° maximum tilt in
ceilings 1.25" - 2" thick. EZ-Aim Helical Drive System provides fast and
accurate hot aiming with Philips screwdriver.
3. Horizontal Adjustment Mechanism: Die-form steel ring, matte black
finish. Provides 362° horizontal stop, lockable with Philips screwdriver.
4. Lamp Support: Die-form aluminum with knurled surface for easy gripping
during relamping. Spring tension clips hold lamp and lens and allow fast
snap-in, snap-out relamping. Matte black finish. Accepts one 2" dia.
accessory.
5. Cover Glass: High temperature, soft focus lens.
6. Thick Ceiling Ready Brackets: Die-form steel, matte black finish.
Adjust trim kit vertically to accommodate up to 2" thick ceiling, lockable.
7. Lampholder: Porcelain bi-pin socket. Pre-wired with No.18 AWG
Teflon leads.
8. Frame Vertical Adjustment Mechanism (C3LV): Accommodates
mounting to virtually any ceiling system using pre-installed mounting
bars, or 1/2" EMT tubing (by others). Single locking features secures all
adjustments. Alignment holes and markings allow fixture to be pre-set prior
to installation. Final adjustment can be made from below inside fixture.
9. Mounting Bars (C3LV): Galvanized steel, 0.048"; pre-installed
telescoping bars extend from 20" to 30" long and lock securely into
position. Built-in locking tabs provide positive attachment to common T-
bar systems. Self-centering feature simplified installation in 24"O.C. grid
systems. Attaches to steel or wood joists without accessories.
10. Transformer: Replaceable from below. Magnetic: 120V/277V 60 Hz. dual-
voltage, core & coil. Note: Magnetic not recommended for residential or
Spec. Sheet
Evolution Pinhole Adjustable Accent
®
C3MRPA
5" (127mm)
9 5/8"
5 1/2"
(140mm)
5" (127mm)
5"
(127mm)
Plus Ceiling
Thk.
14 5/8"
(372mm)
1/2"
(13mm)
9" (229mm)
Trim Plate
Satin Aluminum Flangeless
NA C3MRPA WHFT
NA C3MRPA BKFT
C3MRPA SA C3MRPA SAFT
11 2 6 4 5 7 3
1 1/4" Dia.
(32mm)
4" (102mm) Dia.
C3LV
Flangeless Trim with
(229mm)
Plaster Ring Accessory
9 1/2"
(242mm)
3 3/8" (86mm) Dia.
Frame-In Kit
C3LV Non-IC Magnetic 120/277V
C3LVE1 Non-IC Electronic 120V
C3LVE2 Non-IC Electronic 277V
C3ALV Non-IC AirSeal Magnetic 120/277V
®
C3ALVE1 Non-IC AirSeal Electronic 120V
®
C3ALVE2
Non-IC AirSeal ® Electronic 277V
C3AICLV IC AirSeal Magnetic 120V
®
C3AICLVE1 IC AirSeal Electronic 120V
®
Note: Magnetic not recommended for residential or noise sensitive areas.
noise sensitive areas. Electronic: 120V or 277V 50/60 Hz., regulated lamp
voltage, HPF, EMI and circuit protections, thermal auto-reset, quiet
operation.
11. Frame-In Kit: See Frame-In Kit specification sheets for more information.
Non-IC and Non-IC AirSeal - Insulation must be kept 3" away from any
®
parts of the luminaire and must not be placed above luminaire in a manner
which will entrap heat.
IC AirSeal - Luminaire may be in direct contact with thermal insulation.
®
Labels
U.L. (Suitable For Damp Locations), I.B.E.W.
* Lamp wattage restriction for Non-IC: 65W for up to 1" thick ceiling, 50W
for ceiling thickness greater than 1" (up to 2").

Options and Accessories

2" dia. Color Filters/Specialty filters: See ADF2/AF2 specification sheets
2" dia. Louver: AL2HC
Plaster Trim Ring (use with flangeless trim): CA3FMR
Chicago Plenum: Consult Factory
Job Information
Job Name:
Cat. No.:
Lamp(s):
Notes:
Lightolier
a Genlyte company
631 Airport Road, Fall River, MA 02720 • (508) 679-8131 • Fax (508) 674-4710
We reserve the right to change details of design, materials and finish.
© 2011 Genlyte Group LLC • G0711
C3MRPA
1 1/4" Aperture, MR16 (12V)
8 10 9
Vertical Adjustment
1" (25mm) to
2 3/4" (70mm)
2" (59mm) Max.
1
Ceiling Thk.
9"
1/2" (13mm) C3AICLV
Lamp*
42W-65W MR16 (12V)
20W-65W MR16 (12V)
20W-65W MR16 (12V)
42W-65W MR16 (12V)
20W-65W MR16 (12V)
20W-65W MR16 (12V)
20W-50W MR16 (12V)
20W-50W MR16 (12V)t
Type:
www.lightolier.com