I Hi-Fi Stereo Sound System; Selecting The Sound Mode; I Preset For Use; Video Channel Setting - Hitachi DVPF2EUK Instruction Manual

This DVD/VCR will record and playback Hi-Fi stereo sound. In addition it has a NICAM stereo sound decoder.
This equipment will receive stereo and bilingual broadcasts and there are several ways of recording and play-
ing back the sound.
You can select each mode by pressing the AUDIO Button on the remote control. Each mode is indicated on the
TV screen as following.
• During playback of the recorded tape in
Hi-Fi mode:
Mode AUDIO OUTPUT
L Hi Fi L Audio
Stereo
R Hi Fi R Audio
L Hi Fi L Audio
L
R Hi Fi L Audio
L Hi Fi R Audio
R
R Hi Fi R Audio
L Normal Audio
Normal
R Normal Audio
Notes
¡
If you play non-Hi-Fi tapes, the DVD/VCR will play automatically in monaural even if you select any mode.
¡
If the stereo signal becomes weak, the broadcast is automatically recorded in monaural.

VIDEO CHANNEL SETTING

Skip This Section When Connected By SCART.
Video channel setting will be necessary, if your
DVD/VCR is connected to the TV via the coaxial
cable.
• Use the remote control for this procedure.
1
Insert a pre-recorded tape into the
DVD/VCR.
• The DVD/VCR will turn on and start playback
automatically.
If playback does not start, press the
2
Select and adjust your TV to channel 35.
• If the playback picture appears on the TV screen,
continue with step 8.
• If channel 35 is employed for broadcasting, or
interference lines appear on the picture, the RF
converter must be set to a different channel
between CH22 and CH69. Continue with step 3.
3
Press the MENU Button.
4
Press the or C Button repeatedly to
B
select "INITIAL". Then,
press the Button.
g
HI-FI STEREO SOUND SYSTEM

SELECTING THE SOUND MODE

• Reception of stereo broadcasts:
Display on
Mode AUDIO OUTPUT
the TV screen
L
STEREO Stereo
R
L
LEFT L
R
L
RIGHT R
R
L
- None - Monaural
R
PRESET FOR USE
VCR
Button.
B
MENU
TIMER
SET UP
INITIAL
Display on
the TV screen
L Audio
STEREO
R Audio
L Audio
LEFT
L Audio
R Audio
RIGHT
R Audio
L+R Audio
- None -
L+R Audio
5
Press the
select to "RF OUT". Then, press the
Button.
• The RF OUT CH menu will appear.
INITIAL
CH TUNING
CLOCK
RF OUT
6
Press the
which is not used for broadcasts between
channel 22 and channel 69 in your area, then
press the
7
Press the MENU button to exit.
• Set the TV channel to the RF OUT CHANNEL
which was selected on the DVD/VCR. Press
picture from the DVD/VCR will appear on the TV
screen. If a picture does not appear, repeat steps 3
to 7 using a different channel which is not used for
broadcasts.
8
Press C to stop the tape.
Notes
• You may also access the RF OUT CH menu by
pressing and holding MENU on the remote control
for 3 seconds during power off until the RF OUT
CH menu appears.
• If your DVD/VCR and TV are connected using a
SCART cable there is no need to have the RF con-
verter operating so it can be switched off and avoid
the possibility of interference.
– 20 –
• During reception of bilingual broadcasts:
Mode AUDIO OUTPUT
L Main Audio
MAIN
R Main Audio
L Sub Audio
SUB
R Sub Audio
L Main Audio
MAIN
SUB R Sub Audio
or C Button repeatedly to
B
RF OUT CH 35
or C Button to select a channel
B
Button.
g
VCR
Display on
the TV screen
MAIN
SUB
MAIN
SUB
g
. A
B
EN
2C15