Download Print this page

Hitachi CM715ET User Manual

Hide thumbs


Quick Links

For future reference, record the serial number of your color monitor.
The serial number is located on the rear of the monitor.
This monitor is E
computer equipped with VESA DPMS.
The E
of any product or service.
As an E
product meets the E
compliant when used with a
emblem does not represent EPA endorsement
Partner, Hitachi,Ltd. has determined that this
guidelines for energy efficiency.




  Related Manuals for Hitachi CM715ET

  Summary of Contents for Hitachi CM715ET

  • Page 1: User Manual

    VESA DPMS. ® The E emblem does not represent EPA endorsement NERGY of any product or service. ® As an E Partner, Hitachi,Ltd. has determined that this NERGY ® product meets the E guidelines for energy efficiency. NERGY...
  • Page 2: Table Of Contents

    Table of Contents Introduction ..............2 Features Package Overview Cautions................ 3 TCO'99 Statement ............6 For the Customers in the UK ...........8 Installation ..............10 User Controls..............11 Osd Function Description ..........12 Osd Icon Summary ............13 Specifications ..............14 Troubleshooting ..............15 M o n i t o r...
  • Page 3: Introduction

    INTRODUCTION Congratulations on your purchase of this high performance 19”moniter. Using state-of-the-art electronics, this monitor can support up to 1600 x 1200 resolution. The on-screen display(OSD) allows you to customize the display setting to suit your individual needs. Features ☺ 19-inch monitor with a large, 350 x 260 mm viewable screen for comfortable viewing.
  • Page 4: Cautions

    CAUTIONS NEVER REMOVE THE REAR COVER ! The rear cover MUST be removed only by authorized service personnel. This colour monitor contains high voltage components. THE RECEPTACLE SHOULD BE CLOSE TO THE MONITOR AND EASILY ACCESSIBLE ! INSTALL THE UNIT IN A SUITABLE ENVIRONMENT ! DO NOT expose this monitor to rain or moisture to prevent electric shock or fire hazard.
  • Page 5 USE ONLY THE CORRECT VOLTAGE POWER OUTLET WITH SAFETY GROUND CONNECTION ! 200 - 240 V for Europe, etc. CAUTION for 200 - 240V operation only This equipment relies on the protective devices in the building installation for short-circuit and over-current protection.
  • Page 6 BE CAREFUL OF STATIC ELECTRICITY ON CRT SURFACE ! To prevent electrical shock by the static electricity on the CRT surface, disconnect the power cord at least 30 SECONDS AFTER turning off the power. ABOUT CLEANING This monitor has a non-glare and anti-electrostatic treatment on the surface of the screen. Use water or alcoholic solvent with soft cloth like gauze to clean the surface of the screen.
  • Page 7: Tco'99 Statement

    TCO'99 Statement Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. This product meets the requirements for the TCO'99 scheme which provides for an international environmental and quality labelling of personal computers.
  • Page 8 Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet) : Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: Environmental requirements...
  • Page 9: For The Customers In The Uk

    CAUTIONS (Continued) For the Customers in the UK THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE UK PLEASE REFER TO THE NOTES ON THIS PAGE. IMPORTANT FOR UNITED KINGDOM WORDING FOR CLASS EQUIPMENT INSTRUCTION BOOKS AND LABELS The mains lead on this equipment is supplied with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug.
  • Page 10 NOTE: The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual. TRADEMARK ACKNOWLEDGEMENT VGA is a registered trademark of International Business Machines Corporation. VESA is a trademark of a nonprofit organization, Video Electronics Standard Association. ®...
  • Page 11: Installation

    INSTALLATION 1. Connect the monitor signal cable to the 15-pin mini D-sub (VGA) on the computer. 2. Connect the power cord to the power connector on the back panel of the monitor, then plug the other and into an appropriately grounded electrical outlet that is easily accessible and close to the monitor.
  • Page 12: User Controls

    USER CONTROLS Power button Power LED Indicator LED Color State Turn monitor on and off. Green Yellow Sleep Select button & Adjustments For adjusting the display For selecting OSD parameters in the selected functions. function.
  • Page 13: Osd Function Description

    OSD FUNCTION DESCRIPTION Press any button to display the OSD Menu. To select function, press the button. To adjust function, press the button. To exit the OSD menu, select the Exit icon, then press the button once.
  • Page 14: Osd Icon Summary

    OSD ICON SUMMARY Icon Function Function Description Brightness Adjusts display brightness Contrast Adjusts display contrast H. Size Increases and decreases screen width H. Position Shifts display image right or left V. Size Increases and decrease screen height V. Position Shifts display image up or down Pin.
  • Page 15: Specifications

    SPECIFICATION Screen Size 19" CRT Horizontal dot pitch 0.22 mm Horizontal mask pitch 0.21 mm Surface Non-glare Viewable Image Area (mm) 350 x 260 Input Signal Video signals. RGB Analog 0.7Vp-p / 75 Ohm a. Separate H/V, TTL (+/-) b. Composite H+V, TTL (+/-) Scanning Frequency Horizontal (KHz) 30 - 95...
  • Page 16: Troubleshooting

    TROUBLESHOOTING Please make reference to following solutions for most of the failure symptoms occurred. If the symptom remains after trying the suggested solutions, please contact your local authorized service center. Problem: Power LED is not lit when monitor is powered on. Check to make sure that the power cord is properly connected.
  • Page 17 Fax: +46 (0) 8 562 711 13 Tel: +39 02 38073415 Servizio Clienti Email: Fax: +39 02 48786381/2 Email: HITACHI EUROPE S.A.S HITACHI EUROPE LTD (Norway) AB Lyon Office STRANDVEIEN 18 B.P. 45, 69671 BRON CEDEX 1366 Lysaker FRANCE...