Child Craft 15061 Manual

CCH00701:09/00
JCHE p65
15061,16101,16151,16191,16281
PH: 812-883-3111 - FAX: 812-883-1819 - http://www.childcraftind.com
A S S E M B L Y
READ ALL INSTRUCTIONS WITH CARE BEFORE STARTING THE ASSEMBLY PROCEDURE.
YOU WILL NEED A #2 PHILLIPS SCREWDRIVER, A SLOTTED SCREWDRIVER AND A HAMMER.
(12) Slotted/Phillips
A A A A A
Machine Screws
(actual size)
(4) Compression
F F F F F
Springs
(1) Footboard
O O O O O N N N N N
Carefully remove and lay out all hardware and parts. Remove wires securing the (2) Stabilizer Bars J J J J J and the (4) Crib Rods K K K K K to Crib Spring R R R R R . Check
quantities and match to the three Parts Lists above. If any part is missing or broken contact your dealer or Child Craft (P.O. Box 444, Salem, IN 47167-
0444 USA (ph# 812/883-3111), service@childcraftind.com for a replacement part or instructional literature. Before making this contact, identify your crib.
A model identification number is stamped on the underneath side of the bottom rail of either a crib end N N N N N /O O O O O or a crib side P P P P P /Q Q Q Q Q . Record the model
Identification Number now: # ______________________. Include this number with a request for a part or instructional literature. DO NOT SUBSTITUTE
PARTS!
S 1 - D
TEP IAGRAM
Note the two piece assembly of 4-Position Spring Hanger Brackets D D D D D . Before
attachment to crib (ends) N N N N N &O, check to be sure the moulded plastic backer
aligns with the 4-Position Spring Hanger Bracket D D D D D as shown. These items are
shipped assembled, in the unlikely event they should become detached during
shipment, simply take the plastic backer, align with the holes in the metal bracket
and snap together to create an assembly as shown in the Hardware Parts Diagram.
IMPORTANT! All four plastic tabs on each moulded plastic backer should project
toward the metal hooks on 4-Position Spring Hanger Brackets D D D D D . If you should
find a tab on an uninstalled 4-Position Spring Hanger Bracket not so projected,
simply use a screwdriver to push tab forward until it contacts the metal hook. If
a plastic tab is not projected on a factory installed 4-Position Spring Hanger Bracket
simply place a small slotted screwdriver underneath the plastic tab and pull
forward until it contacts the metal hook. Attach a 4-Position Spring Hanger Bracket
D D D D D , (2 piece assembly) , to both Headboard N N N N N & Footboard O O O O O with Slotted/Phillips
Wood Screws E E E E E , to be positioned exactly as the ones already factory installed.
Attach Angle Brackets I I I I I with Slotted/Phillips Wood Screws E E E E E to Headboard N N N N N
and Footboard O O O O O , to be positioned exactly as the ones already factory installed.DO
NOT REMOVE 4-POSITION SPRING HANGER BRACKETS OR ANY OTHER
HARDWARE ITEM ATTACHED WITH SLOTTED/PHILLIPS WOOD SCREWS E E E E E .
CHILD CRAFT INDUSTRIES, INC.
P.O. Box 444, Salem, IN USA 47167-0444
D I R E C T I O N S
P E H
ARTS NCLOSED IN ARDWARE
(4) Spring Hangers
B B B B B
(4) Bumper
G G G G G H H H H H
Springs
P
ARTS
(1) Headboard
P P P P P
(2) Crib sides
(Dropsides)
1: A 4-P
TTACH OF
child craft child craft
child craft
child craft child craft
A N D
B (
AG NOTED WHEN SHOWN ACTUAL SIZE
(4) Gate Shoes
C C C C C
Moulded
backers
(4) Casters
(style may vary)
I C
NCLUDED IN ARTON
(1) Spring
Q Q Q Q Q R R R R R
&
P
REPARATION
S H
OSITION PRING ANGER
D
P A R T S
)
D D D D D E E E E E
(2)
plastic
(2)
4-Position
Spring
Hanger
Brackets
(2) Stabilizer Bars
J J J J J
K K K K K
B A B
RACKETS AND NGLE
D D D D D
E E E E E
Factory
installed
I I I I I
E E E E E
1
D C
OUBLE ROPSIDE RIB
L I S T
(18) Slotted/Phillips
Wood Screws
(actual size)
(2) Angle
I I I I I
Brackets
(4) Crib Rods
.
RACKETS
O O O O O
Holes to
receive
Slotted/
Phillips
D D D D D
Wood
Screws
E E E E E