Table of Contents
Advertisement
Quick Links
•
5216 Portside Dr., Medina, OH 44256 USA
tHis is tHe Assembly instrUctions
For cribs solD in tHe UniteD stAtes
A
Directions for Maintenance, Cleaning, Storage and Use of your Crib are also included.
BEFORE STARTING THE ASSEMBLY PROCEDURE, READ ALL DIRECTIONS WITH CARE.
YOU WILL NEED THE FOLLOWING FOR THE ASSEMBLY OF YOUR CRIB/TODDLER BED:
# 1 a n d # 2 P h i l l i p S c r e w d r i v e r s
P
Arts
(8) Allenhead Bolts
(actual size)
E
(4) W
(6) Allenhead Bolts
aSherS
I
(1) Crib Stretcher
(for use with Toddler Bed only)
J
(2) Stationary Sides
Foundations Worldwide, Inc.
www.childcraftbaby.com
D
ssembly
irections AnD
e
H
ncloseD in
ArDwAre
A
(2) Allen Wrenches
F
(actual size)
P
Arts
•
PH: 330.722.5033
P
S l o t t e d S c r e w d r i v e r
b
(
Ag
noted when shown actual size
B
(12) Connector Nuts
(2) Allenhead Bolts
(actual size)
e
c
ncloseD in
Arton
K
(2) End Panels
(2) Spring
Brackets - Right
c
/t
rib
•
FAX: 330.722.5037
l
Arts
ist
E n c l o s e d A l l e n Wr e n c h e s B
)
C
(4) Flat Head Bolt
(actual size)
G
(2) Joint Connector Nut
Pouches
(storage for
Assembly Directions)
M
(2) Spring
Brackets - Left
1
b
oDDler
eD
10031
D
H
(actual size)
L
(1) Spring
N
AB20165 C
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Child Craft 10031
Summary of Contents for Child Craft 10031
- Page 1 10031 Foundations Worldwide, Inc. • • • 5216 Portside Dr., Medina, OH 44256 USA PH: 330.722.5033 FAX: 330.722.5037 www.childcraftbaby.com tHis is tHe Assembly instrUctions For cribs solD in tHe UniteD stAtes ssembly irections AnD Arts Directions for Maintenance, Cleaning, Storage and Use of your Crib are also included.
- Page 2 rePArAtion Carefully remove and lay out all hardware and parts. During the assembly process, when using screws or bolts (fastening devices), check each with P list by letter and size. Identify by placing each fastening device on the diagram of Arts ncloseD in ArDwAre...
- Page 3 2 - D 2: A iAgrAm ttAcH tAtionAry iDeS to ootboArD eADboArD Place the (8) Connector Nuts C into their holes in the corner posts of End Panel K as shown. Align the holes in an end rail of a Stationary Side J with the holes in End Panel K. Insert Allenhead Bolts A through the end rail on Stationary Side Note: Large J, then tighten into Connector Nuts C in End Panel K by...
- Page 4 4: F inisHing oUcHes Place a purchased mattress on Spring L. After completing crib assembly, review Warnings on page 7. Also review Cautions, Cleaning, Storage, Use and Maintenance of crib on pages 6 and 7. Store the assembly directions in the pouch which was pre-attached to Spring L. For future referral to assembly directions you will only need to remove them from the pouch.
- Page 5 oDDler onversion When use as a crib has been completed, you have the option to convert your crib to a toddler bed for years of additional use in your child's room. Remove one Stationary Side J and install Spring L in its lowest position. Store removed parts and hardware as perhaps sometime in the future you may want to convert the toddler bed back into a crib.
- Page 6 WARNING (For Toddler Bed) WARNING: INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT. Openings in and between bed parts can entrap head and neck of a small child. NEVER use bed with children younger than 15 months. ALWAYS follow assembly instructions. WARNING: STRANGULATION HAZARD: NEVER place bed near windows where cords from blinds or drapes may strangle a child.
- Page 7 WARNING • FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: Infants can suffocate on soft bedding. NEVER add a pillow or comforter. NEVER place additional padding under an infant. • Read all instructions before assembling crib.
Need help?
Do you have a question about the 10031 and is the answer not in the manual?
Questions and answers