Related Manuals for Newcon Optik LAM 10M IR
Summary of Contents for Newcon Optik LAM 10M IR
- Page 1 Operation Manual LAM 10M IR LASER AIMING MODULE / TARGET POINTER 105 Sparks Ave., Toronto, ON, M2H 2S5, Canada...
-
Page 3: Important Information
IMPORTANT INFORMATION Read prior to activation You have just purchased a sophisticated electronic device. To operate it properly, please read this manual carefully. LAM belongs to Class I laser products in accordance with IEC 60825-1. Here are some common precautions that must be observed. -
Page 4: Table Of Contents
CONTENTS Brief description ..........2 Device design ............. 3 DELIVERY SET ..........8 3.1. Standard delivery set........8 3.2. Optional parts..........8 Specifications............9 OPERATION INSTRUCTIONS...... 10 5.1. Installing the battery ........10 5.2. Mounting LAM on a weapon....... 10 5.3. -
Page 5: Brief Description
Carefully read all the instructions prior to use. Failure to obey the instructions will void the warranty INVISIBLE LASER RADIATION CLASS I LASER PRODUCT 830–860 nm 0,1mW. Brief description LAM 10M IR laser aimer (hereinafter referred as LAM) is designed for precise aiming at night time. LAM forms an IR laser radiation spot on the target visible only through the night vision goggles. -
Page 6: Device Design
Device design... - Page 7 Fig. 1. LAM 10M IR 1 – clamp 2 – bracket 3 – stopper 4 – remote connector 5 – body 6 – emitter 7 – emitter cap 8 – emitter protective cap 9 – windage adjustment 10 – fastener 11 –...
- Page 8 LAM consists of an emitter (6,7, Fig.1), a battery compartment (15,16, Fig.1), windage (9, Fig.1) and elevation (12, Fig.1) adjustment mechanisms, an operating modes switch (17, Fig.1), a remote switch (Fig.2), a clamp (1, Fig.1). A battery is to be inserted into the battery compartment (16, Fig.1).
- Page 9 LAM automatically turns off after 30 minutes of being switched in positions C and R. In order to activate LAM after it has automatically turned off, return the switch (17, Fig.1) into OFF position and then switch it to the desired position again.
- Page 10 1 — key; 2 — velcro tape; 3 — connector Fig. 2. Remote switch...
-
Page 11: Delivery Set
3. DELIVERY SET 3.1. Standard delivery set LAM is supplied in the following assembly: Quantity, pcs LAM 10M IR Remote switch Velcro tape O-Ring Case Manual Battery CR123 3.2. Optional parts LAM can be supplied with a barrel mount. -
Page 12: Specifications
Specifications Laser wavelength 830…850 nm Beam divergence 0.5 mrad Spot size at 50 meters 25 mm Windage and elevation adjustment range ±20 mrad Windage and elevation adjustment step 0.5 mrad (50 mm @100m) Accuracy of adjustment after 1000 shots 0.1 mrad Accuracy of adjustment after 100 re- 1 mrad mountings on a rail... -
Page 13: Operation Instructions
OPERATION INSTRUCTIONS 5.1. Installing the battery LAM is powered by a standard Lithium CR123 3V battery. To install a battery: unscrew the battery compartment cap (15, Fig.1), insert a battery observing the polarity as marked on the battery compartment, check the condition of the O-ring on the body; replace it if worn or torn, screw the battery compartment cap back on. -
Page 14: Connecting The Remote Control
5.3. Connecting the remote control To connect the remote switch (Fig.2): unscrew the cap of the remote connector (4, Fig.1) and store it in a safe place, plug in the remote connector contact (3, Fig.2) observing the key visible on the cable side, tighten the union nut, attach the remote switch to the weapon pivot or grip with velcro tape (2, Fig.2). - Page 15 remove protective cap (8, Fig. 1) from emitter tube output window; activate LAM in mode C; match the center of radiation spot with the aiming mark by means of rotating handwheels of adjustment mechanisms; perform test firing with LAM under the same conditions as when checking the weapon fire capability with an iron sight;...
-
Page 16: Maintenance, Storage And Transportation
Maintenance, storage and transportation 6.1. General LAM is a sophisticated precise optical instrument equipped with electronics. Therefore, it should be handled with due care. Never disassemble LAM. Keep away from direct sunlight, impacts, dust, moisture, and sharp changes of temperature. Do not keep LAM at temperatures higher than 60 (140 F). -
Page 17: Storage
6.2. Storage To set LAM from combat position into a stowed one: turn LAM off (operating modes switch (17, Fig.1) should be set to OFF position); cover emitter tube output window with protective cap (8, Fig.1); disconnect remote switch (Fig.2) from the weapon, loosen screw caps (13, Fig.1), remove LAM with remote switch from Picatinny rail and place it into the case. -
Page 18: Transportation
To apply new layer of lubricant: Within two hours from cleaning apply an even 0.2-0.5 mm thick layer of lubricant on metal surfaces with a brush. Do not cover plastic parts. When preparing for a long-term storage LAM just received from manufacturer or from workshop, ensure that actual set is the same as indicated in the Delivery Set section of this manual. - Page 19 Cover aimer with protective cap. Disconnect the remote switch from the weapon. Dismount LAM from Picatinny rail. Pack LAM and remote switch into the case. When packed, LAMs can be transported by any covered means in accordance with storage conditions as described in this manual.
-
Page 20: Troubleshooting
TROUBLESHOOTING Spot shape or size has changed Emitter objective lens is dirty. Flush emitter lens with fresh water and wipe it with soft cloth. No radiation when activating LAM with remote switch Turn the operating modes switch (17, Fig.1) to OFF position and then turn LAM ON again. -
Page 21: Warranty
NEWCON product for warranty service are your responsibility. Please include a check or money order made out to NEWCON OPTIK for the amount of $15.00 to cover shipping and handling. This covers products shipped in USA or Canada only. -
Page 22: Customer Support
Standard Time. At no time should equipment be sent back to Newcon without following the instructions of our technical support department. NEWCON OPTIK accepts no responsibility for unauthorized returns. To locate NEWCON Authorized Dealer call: Tel: +1(416) 663-6963 Fax: +1(416) 663-9065 Email: newconsales@newcon-optik.com... -
Page 23: Quality Certificate
QUALITY CERTIFICATE LAM10M IR serial number: ________________________________________________ complies with all technical specifications and has passed the quality inspection. Date of production: _________________________________ Quality Inspector: __________________________________ Quality Assurance Seal... - Page 24 NEWCON OPTIK ™ 2011...
Need help?
Do you have a question about the LAM 10M IR and is the answer not in the manual?
Questions and answers