Controlling Other Components; Cd Functions; Dvd Functions; Tuner Functions - Rotel RC-1580 Owner's Manual

English
Controlling Other Components
In addition to operating many of the controls of the RC-1580, the
RR-AT97 remote control can operate basic features of some Rotel CD
players, DVD players, and AM/FM tuners.

CD Functions

/ . ,
The PLAY, STOP, PAUSE,
buttons, and NUMERIC buttons (0 - +10) operate many Rotel CD
players after the CD Listening button on the remote has been pressed.

DVD Functions

/ . ,
The PLAY, STOP, PAUSE,
operate Rotel DVD players, after the AUX1 Listening button on the
remote has been pressed.

Tuner Functions

< >
The BAND, TUNING , and additional tuning feature buttons (PTY,
TA, TP, etc.) operate Rotel tuners, after the TUNER listening button on
the remote has been pressed.
Note: By default, the RR-AT97 operates the Rotel RT-1080/RT-1082/
RT-1084 tuners. The remote can be reprogrammed to operate the RT-
940AX tuner. This programming only needs to be done once:
To program for the RT-940AX: press the ON button and the 2
button simultaneously.
To program for the RT-1080/RT-1082/RT-1084: press the ON
button and the 1 button simultaneously.

Troubleshooting

Most difficulties in audio systems are the result of incorrect
connections, or improper control settings. If you encounter problems,
isolate the area of the difficulty, check the control settings, determine
the cause of the fault and make the necessary changes. If you are
unable to get sound from the RC-1580, refer to the suggestions for the
following conditions:

Standby Power Indicator Is Not Lit

The Standby Power Indicator should be lit whenever the RC-1580 is
plugged into the wall power outlet. If it does not light, test the power
outlet with another electrical device, such as a lamp. Be sure the
power outlet being used is not controlled by a switch that has been
turned off.

Fuse Replacement

If another electrical device works when plugged into the power outlet,
and the Standby Indicator still will not light when the RC-1580 is
plugged into the wall outlet, it indicates that the internal power fuse
may have blown. If you believe this has happened, contact your
authorized Rotel dealer to get the fuse replaced.
{ }
TRACK and, RANDOM
{ }
TRACK and RANDOM buttons

No Sound

Check the signal source to see if it is functioning properly. Make sure
the cables from the signal source to the RC-1580 inputs are connected
properly. Be sure the Listening Selector is set to the proper input. Check
the power amplifier for power and proper operation. Check all the
wiring between the RC-1580 and the power amplifier, and the power
amplifier and speakers.

Resetting the IR Code

If you reset the RC-1580 IR code to use the Bypass function, you can
reset it to the default code using the procedure described in the Note
in the Bypass Function section of this manual. Or you can use the
front panel buttons. While RC-1580 is turned on, press and hold the
Recording Off button for 5 seconds. The LED for the Listening CD
9
button 8 will turn On to indicate the IR code is reset. If the Bypass
LED is lit it will turn Off.

Specifications

Total Harmonic Distortion
(20Hz-20kHz)
Intermodulation Distortion
(60 Hz : 7 kHz, 4:1)
Input Sensitivity / Impedance
Phono - MC
Phono - MM
Line Level
Phono Overload
(MC/MM)
Output Sensitivity / Impedance
Frequency Response
Phono Input
Line Level Input
Tone Controls
Bass
Treble
Signal to Noise Ratio
(IHF "A" weighted)
Phono - MC/MM
Line Level
Power Requirements
USA Version
European Version
Power Consumption
Standby Power Consumption
Dimensions
(W x H x D)
Weight (net)
All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without notice.
11
< 0.004%
< 0.004% at 1V output
250 µV / 100 ohms
2.5 mV / 47 kOhms
150 mV / 220 kOhms
16 mV / 160 mV
1 V/ 100 Ohms
20Hz-20kHz, ±0.2dB
4Hz-100kHz, ±0.5dB
±6dB at 100Hz
±6dB at 10kHz
70 dB/75 dB
100 dB
120 Volts, 60 Hz
230 Volt, 50 Hz
15 Watts
2.5 Watts
431 x 99 x 337 mm
17 x 4 x 13 1 / "
2
7.7 kg, 16.94 lbs.