Bryant 310AAV Installation, Start-Up, Operating And Service And Maintenance Instructions page 3

5 15/16 5 15/16
[150.7] [150.7]
AIR FLOW AIR FLOW
5 1/2 5 1/2
[140.3] [140.3]
Ø7/8 Ø7/8
8 7/16 8 7/16
[22.2] [22.2]
[213.5] [213.5]
ACCESSORY ACCESSORY
9 7/8 9 7/8
[250.7] [250.7]
Ø1/2 Ø1/2
[12.7] [12.7]
27 3/4 27 3/4
THERMOSTAT WIRE ENTRY THERMOSTAT WIRE ENTRY
[704.7] [704.7]
33 1/4 33 1/4
[843.9] [843.9]
Ø7/8 Ø7/8
[22.2] [22.2]
ACCESSORY ACCESSORY
21.6 21.6
[549.5] [549.5]
BOTTOM INLET BOTTOM INLET
28.39 28.39
[721.2] [721.2]
29 29
[736.9] [736.9]
NOTES:
1. Two additional 7/8 ---in. (22 mm) diameter holes are located in the top plate.
2. Minimum return ---air openings at furnace, based on metal duct. If flex duct is used, see flex duct manufacturer's recommendations for equivalent diameters.
(a.) For 800 CFM ---16 ---in. (406 mm) round or 14 1/2 x 12 ---in. (368 x 305 mm) rectangle.
(b.) For 1200 CFM ---20 ---in. (508 mm) round or 14 1/2 x 19 1/2 ---in. (368 x 495 mm) rectangle.
(c.) For 1600 CFM ---22 ---in. (559 mm) round or 14 1/2 x 22 1/16 ---in. (368 x 560mm) rectangle.
(d.) For airflow requirements above 1800 CFM, see Air Delivery table in Product Data literature for specific use of single side inlets. The use of both side
inlets, a combination of 1 side and the bottom, or the bottom only will ensure adequate return air openings for airflow requirements above 1800 CFM.
A
CABINET
FURNACE SIZE
WIDTH
045---08/024045 14--- 3/16 (360)
045---12/036045 14--- 3/16 (360)
070---08/024070
14--- 3/16 (360)
070---12/036070 14--- 3/16 (360)
070---16/048070
17--- 1/2 (445)
090---14/042090 17--- 1/2 (445)
090---16/048090 21 (533)
090---20/060090 21 (533)
110---12/036110 17--- 1/2 (445)
110---16/048110 21 (533)
110---22/066110 21 (533)
135---16/048135 21 (533)
135---22/066135 24--- 1/2 (622)
155---20/060155 24--- 1/2 (622)
*135 and 155 size furnaces require a 5 or 6 ---in. (127 or 152 mm) vent. Use a vent adapter between furnace and vent stack. See Installation Instructions for
complete installation requirements.
5.1 5.1
[130.5] [130.5]
2 1/16 2 1/16
[51.6] [51.6]
1.7 1.7
[43.5] [43.5]
C
Ø7/8 Ø7/8
[22.2] [22.2]
ACCESSORY (2) ACCESSORY (2)
1 15/16 1 15/16
[49.2] [49.2]
AIR FLOW AIR FLOW
2 5/16 2 5/16
3 7/16 3 7/16
[59] [59]
A A
[86.8] [86.8]
B
5 7/8 5 7/8
[148.5] [148.5]
TOP OF CASING TOP OF CASING
Ø7/8 Ø7/8
[22.2] [22.2]
JUNCTION BOX JUNCTION BOX
LOCATION LOCATION
Ø1 3/4 Ø1 3/4
[44.5] [44.5]
GAS ENTRY GAS ENTRY
6.1 6.1
D
[155.7] [155.7]
BOTTOM RETURN BOTTOM RETURN
WIDTH WIDTH
Fig. 1 --- Dimensional Drawing
Table 1—Dimensions - - In. (mm)
B
OUTLET TOP & BOTTOM
WIDTH
FLUE COLLAR
LOCATION
12--- 9/16 (319) 9--- 5/16 (237)
12--- 9/16 (319) 9--- 5/16 (237)
12--- 9/16 (319) 9--- 5/16 (237)
12--- 9/16 (319) 9--- 5/16 (237)
15--- 7/8 (403) 11--- 9/16 (294)
15--- 7/8 (403) 11--- 9/16 (294)
19--- 3/8 (492) 13--- 5/16 (338)
19--- 3/8 (492) 13--- 5/16 (338)
15--- 7/8 (403) 11--- 9/16 (294)
19--- 3/8 (492) 13--- 5/16 (338)
19--- 3/8 (492) 13--- 5/16 (338)
19--- 3/8 (492) 13--- 5/16 (338)
22--- 7/8 (581) 15--- 1/16 (383)
22--- 7/8 (581) 15--- 1/16 (383)
6 13/16 6 13/16
[172.3] [172.3]
5 7/8 5 7/8
[148.5] [148.5] 5 5/8 5 5/8
[143.3] [143.3]
5 7/16 5 7/16
[138.5] [138.5]
1 15/16 1 15/16
[49.2] [49.2]
TOP OF CASING TOP OF CASING
4 13/16 4 13/16
[122.2] [122.2]
9 9/16 9 9/16
[243.3] [243.3]
Ø7/8 Ø7/8
27 3/4 27 3/4
[22.2] [22.2]
[704.7] [704.7]
J.BOX PROVISION J.BOX PROVISION
29 9/16 29 9/16 Ø7/8 Ø7/8
[22.2] [22.2]
[750.7] [750.7]
ACCESSORY ACCESSORY
KNOCK OUTS FOR KNOCK OUTS FOR
3/4 3/4 VENTING(5 VENTING(5
[19.1] [19.1]
PLACES) PLACES)
D
C
BOTTOM
INLET WIDTH
12--- 11/16 (322)
12--- 11/16 (322)
12--- 11/16 (322)
12--- 11/16 (322)
16 (406)
16 (406)
19--- 1/2 (495)
19--- 1/2 (495)
16 (406)
19--- 1/2 (495)
19--- 1/2 (495)
19--- 1/2 (495)
23 (584)
23 (584)
3
8 5/8 8 5/8
[219] [219]
AIR FLOW AIR FLOW
19 19
[481.7] [481.7]
OUTLET OUTLET
Ø1/2 Ø1/2
[12.7] [12.7]
7 13/16 7 13/16
9 11/16 9 11/16
THERMOSTAT WIRE ENTRY THERMOSTAT WIRE ENTRY
[197.8] [197.8]
[245.4] [245.4]
Ø1 3/4 Ø1 3/4
[44.5] [44.5]
GAS ENTRY GAS ENTRY
14 7/8 14 7/8
Ø7/8 Ø7/8
[337.3] [337.3]
[22.2] [22.2]
(BOTH SIDES) (BOTH SIDES)
ACCESSORY ACCESSORY
1 1/4 1 1/4
[31.8] [31.8]
22 1/16 22 1/16
1
[560] [560] [25.4] [25.4]
SIDE INLET SIDE INLET
(BOTH SIDES) (BOTH SIDES)
VENT
SHIP WT
CONNECTION
LB (KG)
SIZE
4 (102) 104 (47)
4 (102) 107 (49)
4 (102) 111 (50)
4 (102) 115 (52)
4 (102) 126 (57)
4 (102) 127 (58)
4 (102) 140 (64)
4 (102) 146 (66)
4 (102) 135 (61)
4 (102) 146 (66)
4 (102) 152 (69)
4 (102)* 149 (68)
4 (102)* 163 (74)
4 (102)* 170 (77)
11 7/16 11 7/16
[290.7] [290.7]
A10290