Table of Contents
Advertisement
MobileHub™ Link
Operation(Optional)
BAND/
8
TEL.
-/J
9
g
f
F/SETUP
Rotary encoder
About MobileHub™ Link
Connect a separately sold junction box and a portable telephone
(available from Nokia) to control the incoming and outgoing calls of
the portable telephone.
Caution
Even with hands-free operation, a driver can be distracted during
telephone operation or receiving a call. For the sake of safety,
drivers are requested to refrain from operating the telephone while
driving.
For the sake of safety, only incoming calls and Speed-Dial
outgoing calls can be operated.
• If a portable telephone is connected, its address book, incoming
and outgoing history are downloaded to the junction box.
• Please refer to the instruction manual of the junction box.
Telephone Mode ON/OFF
1
Press and hold BAND/TEL. for at least 2 seconds
to turn on the Telephone mode.
To turn off, press BAND/TEL.
See relevant pages for each item.
• Press and hold BAND/TEL. for at least 2 seconds. If a portable
telephone is not connected, "NO PHONE" is displayed for about 2
seconds, then the mode returns to the original source mode.
• When the portable telephone is taken off the junction box during an
incoming or outgoing call, or during a hands-free call, the call will
be treated as an ordinary one by the portable telephone.
• When there is an incoming call while the power of CDA-9820XM is
off, the power of CDA-9820XM will turn on automatically for a
hands-free call.
• Even if the power of the portable telephone is off, when CDA-
9820XM is set to Telephone mode, the power of the portable
telephone will be turned on.
• Even if the ACC power of the vehicle is turned off (even if the
engine is stopped) during a hands-free call, the call is not
disconnected, and an ordinary call by the portable telephone is
possible.
• If there is an incoming call during operation (except an outgoing
call or talking), operation mode will end and switch to the
incoming or talking mode.
SEARCH/QS
DISP/
Preset buttons
TITLE
(1 through 6)
• An outgoing call from a portable telephone is also possible.
However, you cannot perform different operations at the same time
from a portable telephone and CDA-9820XM as malfunction can
result.
• With a junction box connected outgoing, incoming, and sending
history will also be recorded in the portable telephone.
• While telephoning, defeat is set to ON. When the call has finished,
the unit returns to your previous setting.
• The telephone volume can be adjusted on the CDA-9820XM. The
volume you set during the call is memorized, and is automatically
applied again on the next call.
• While telephoning or receiving incoming calls, press DISP/TITLE
to show the Network Operator display for 5 seconds.
Incoming Calls
1
Press :/J to receive an incoming call.
2
Press BAND/TEL. to finish a call.
Telephone mode will end and return to the original source
mode.
• When the Automatic Calling mode is on, you can talk after 3
seconds of receiving the incoming call. (see "Setting the Automatic
Calling" on this page.)
Setting the Automatic Calling
The incoming call can be switched to Automatic Calling or Manual
Calling.
1
Press and hold F/SETUP for at least 3 seconds.
2
Select the TEL mode by pressing g or f.
3
Press BAND/TEL. to change to TEL AUTO or TEL
MANU.
4
Press F/SETUP to return to normal mode.
• Press BAND/TEL. during an incoming call to disconnect it.
• The initial setting of the factory is TEL MANU.
Calling
Calling by the address book
You can call up the address book registered in the portable telephone
to call from.
1
Press and hold BAND/TEL. for at least 2 seconds.
2
Press SEARCH/QS
Book) mode.
A list in alphabetic order is displayed.
Retrieving an addressee by Alphabetic Sort List
3
When displaying the Alphabetic Sort List, turn the
Rotary encoder or press g or f to select
the addressee.
4
Press :/J or Rotary encoder to place a call.
5
Press BAND/TEL. to end the call.
Telephone mode will end and return to the original source
mode.
to select PHONE BK (Phone
19
-EN
Hide quick links:
Advertisement
Table of Contents
