Mobilehub™ Link Operation(Optional); About Mobilehub™ Link; Telephone Mode On/Off; Incoming Calls - Alpine CDA-9831 Owner's Manual

MobileHub™ Link
Operation(Optional)
BAND/
SOURCE/
TITLE
-/J TEL.
POWER
Rotary
f
g MENU
encoder
About MobileHub™ Link
Connect a separately sold junction box and a portable telephone
(available from Nokia) to control the incoming and outgoing calls of
the portable telephone.
Caution
Even with hands-free operation, a driver can be distracted during
telephone operation or receiving a call. For the sake of safety,
drivers are requested to refrain from operating the telephone
while driving.
For the sake of safety, only incoming calls and Speed-Dial
outgoing calls can be operated.
• If a portable telephone is connected, its address book, incoming
and outgoing history are downloaded to the junction box.
• Please refer to the instruction manual of the junction box.

Telephone Mode ON/OFF

Press and hold BAND/TEL. for at least 2 seconds to
turn on the Telephone mode.
To turn off, press BAND/TEL.
See relevant pages for each item.
• "NO PHONE" is displayed for about 2 seconds, if a portable
telephone is not connected, before entering the telephone mode.
Then the mode returns to the original source mode
• When the portable telephone is taken off the junction box during an
incoming or outgoing call, or during a hands-free call, the call will
be treated as an ordinary one by the portable telephone.
• When there is an incoming call while the power of CDA-9831/
CDA-9830 is off, the power of CDA-9831/CDA-9830 will turn on
automatically for a hands-free call.
• Even if the power of the portable telephone is off, when CDA-9831/
CDA-9830 is set to Telephone mode, the power of the portable
telephone will be turned on.
• Even if the ACC power of the vehicle is turned off (even if the
engine is stopped) during a hands-free call, the call is not
disconnected, and an ordinary call by the portable telephone is
possible.
• If there is an incoming call during operation (except an outgoing
call or talking), operation mode will end and switch to the
incoming or talking mode.
28
-EN
SEARCH
8
9
F Preset buttons
(1 through 6)
• An outgoing call from a portable telephone is also possible.
However, you cannot perform different operations at the same time
from a portable telephone and CDA-9831/CDA-9830 as
malfunction can result.
• With a junction box connected outgoing, incoming, and sending
history will also be recorded in the portable telephone.
• While telephoning, defeat is set to ON. When the call has finished,
the unit returns to your previous setting.
• The telephone volume can be adjusted on the CDA-9831/CDA-
9830. The volume you set during the call is memorized, and is
automatically applied again on the next call.
• While telephoning or receiving incoming calls, press TITLE
show the Network Operator display for 5 seconds.

Incoming Calls

1
Press :/J to receive an incoming call.
2
Press BAND/TEL. to finish a call.
Telephone mode will end and return to the original source
mode.
• When the Automatic Calling mode is on, you can talk after 3
seconds of receiving the incoming call. (See "Setting the Automatic
Calling" described below.)

Setting the Automatic Calling

The incoming call can be switched to Automatic Calling or Manual
Calling.
1
Press MENU to select the SETUP mode.
2
Select the TELEPHONE (TEL for CDA-9830) mode
by pressing g or f.
3
Turn the Rotary encoder to change to AUTO or
MANUAL (MANU for CDA-9830).
4
Press MENU to select RETURN.
The unit returns to normal mode.
Pressing and holding MENU for at least 2 seconds will
return to normal mode.
• Press BAND/TEL. during an incoming call to disconnect it.
• The initial setting of the factory is MANUAL.
to