Nokia E70 User Manual page 73

S e t t i n g s
WEP key settings
Select Menu Tools Settings
> >
Options > Edit.
In the access point settings, select
In an Ad-hoc network, all devices must use the same WEP key.
Select WLAN security sett.
WEP encryption — Select the desired WEP encryption key length.
•
WEP key format — Select whether you want to enter the WEP key data in
•
WEP key — Enter the WEP key data.
•
802.1x security settings
Select Menu Tools Settings
> >
Options > Edit.
In the access point settings, select
802.1x authenticates and authorizes devices to access a wireless network and prevents access if the authorization process fails.
Select WLAN security sett.. and from the following settings:
WPA mode — Select EAP
•
EAP plug-in settings — If you selected
•
access point.
Pre-shared key — If you selected
•
wireless LAN to which you connect.
The settings available for editing may vary.
WPA security settings
Select Menu Tools Settings
> >
Options > Edit.
In the access point settings, select
Select WLAN security sett.. and from the following settings:
WPA mode — Select EAP
•
EAP plug-in settings — If you select
•
point.
Pre-shared key — If you select
•
wireless LAN to which you connect.
TKIP encryption — To enable TKIP encryption, based on transient keys changed often enough to prevent misuse, select
•
Allowed. All devices in the wireless LAN must either allow or prevent the use of TKIP encryption.
The settings available for editing may vary.
EAP
To view the EAP (extensible authentication protocol) plug-ins currently installed in your device (network service), select
Tools Settings Connection
> >
LAN as a data bearer and
EAP plug-in settings, and press the joystick.
EAP settings
Select Menu Tools Settings
> >
Options > Edit.
Select WLAN security mode
Select WLAN security sett.
The extensible authentication protocol (EAP) plug-ins are used in wireless networks to authenticate wireless devices and
authentication servers, and the different EAP plug-ins make possible the use of various EAP methods (network service).
To use an EAP plug-in when you connect to a WLAN using the access point, select the desired plug-in and
EAP plug-ins enabled for use with this access point have a check mark next to them. To not use a plug-in, select
Disable.
To edit the EAP plug-in settings, select
To change the priority of the EAP plug-in settings, select
ins when connecting to the network with the access point, or
authentication after attempting to use other plug-ins.
The available options may vary.
Copyright © 2006 Nokia. All Rights Reserved.
Connection Access
> >
WLAN security mode
WEP key settings and from the following settings:
>
Connection Access
> >
WLAN security mode
(Extensible Authentication Protocol) or
WPA mode
WPA mode Pre-shared
>
Connection Access
> >
WLAN security mode
(extensible authentication protocol) or
WPA mode > EAP, select which EAP plug-ins defined in your device to use with the access
WPA mode Pre-shared
>
Access points. Select
>
802.1x or WPA/WPA2 as their security mode. Select
Connection Access
> >
802.1x or WPA/WPA2.
>
WPA mode > EAP, scroll to
>
Options > Configure.
points. Select Options
>
> WEP.
ASCII
points. Select Options
>
> 802.1x.
Pre-shared key
> EAP, select which EAP plug-ins defined in your device to use with the
key, enter the shared private key that identifies your device to the
points. Select Options
>
> WPA/WPA2.
Pre-shared key
key, enter the shared private key that identifies your device to the
Options New access point
>
WLAN security sett.
points. Select Options
>
EAP plug-in settings, and press the joystick.
Options Raise priority
>
Options Lower priority
>
73
New access point; or select an access point and
or Hexadecimal format.
New access point; or select an access point and
(a secret key used for device identification).
New access point; or select an access point and
(a secret key used for device identification).
and define an access point that uses wireless
WPA mode
>
New access point, or select an access point and
to attempt to use the plug-in before other plug-
to use this plug-in for network
Menu
>
> EAP, scroll to
Options > Enable. The
Options
>