Set Up An Internet Access Point For Packet Data (Gprs); Advanced Internet Access Point Settings For Packet Data (Gprs); Set Up An Internet Access Point For Wireless Lan - Nokia E70 User Manual

C o n n e c t i v i t y
Callback type — Select
•
Callback number — Enter your data call phone number of your device, which the callback server uses.
•
Use PPP compress. — Select
•
Use login script — Select Yes, if your Internet service provider requires a login script, or if you want to automate your login.
•
A login script is a sequence of instructions that the system follows during the login process.
Login script — Enter the login script. This setting is available only if you have selected
•
Modem initialisation — Enter a command string for the connection setup, if required by your service provider.
•

Set up an Internet access point for packet data (GPRS)

1. Select Menu Tools
> >
2. Select Options New access
>
start with an empty access point, select
3. Define the following settings.
Connection name — Enter a descriptive name for the connection.
•
Data bearer — Select
•
Access point name — Enter the name for the access point. The name is usually provided by your service provider or network
•
operator.
User name — Enter your user name if required by the service provider. User names are often case-sensitive and provided
•
by your service provider.
Prompt password — Select
•
device memory and automate the login.
Password — Enter your password if required by the service provider. The password is often case-sensitive provided by
•
the service provider.
Authentication — Select
•
when possible.
Homepage — Enter the Web address of the page you want to display as a home page when you use this access point.
•
4. After defining the settings, select
and exit.

Advanced Internet access point settings for packet data (GPRS)

After setting up a basic Internet access point for packet data (GPRS), select
advanced settings.
Network type — Select
•
and from your device.
Phone IP address — Enter the IP address of your device. Select
•
This setting is shown only if you select
DNS address — Enter the IP addresses of the
•
or network operator. Otherwise, the name server addresses are provided automatically.
Proxy serv. address — Enter the address of the proxy server. Proxy servers are intermediate servers between a browsing
•
service and its users, which are used by some service providers. These servers may provide additional security and speed up
access to the service.

Set up an Internet access point for wireless LAN

1. Select Menu Tools
> >
2. Select Options New access
>
start with an empty access point, select
3. Define the following settings.
Connection name — Enter a descriptive name for the connection.
•
Data bearer — Select
•
WLAN netw. name
•
select Enter manually. To select the network from the wireless LANs in range, select
Network status — Select
•
WLAN netw. mode
•
through a wireless LAN access point. If you select Ad-hoc, devices can send and receive data directly with each other, and
no wireless LAN access point is needed.
WLAN security mode
•
WEP (wired equivalent privacy), 802.1x, or WPA (Wi-Fi protected access), you must also configure the relevant additional
settings.
WLAN security sett.
•
Copyright © 2006 Nokia. All Rights Reserved.
Use server no. or Use other
Yes to speed up the data transfer, if it is supported by the remote PPP server.
Settings Connection
> >
point. To use an existing access point as a basis for the new one, select
Use default
Packet data.
Yes to enter your password each time you log into a server or
Secure to always send your password encrypted or
Options Advanced settings
>
IPv4 or IPv6 as the Internet protocol type. The Internet protocol defines how data is transferred to
Network type
Primary DNS address
Settings Connection
> >
point. To use an existing access point as a basis for the new one, select
Use default
Wireless LAN.
— To enter the service set identifier (SSID), that is, the name that identifies the specific wireless LAN,
Hidden if the network you are connecting to is hidden, or
— If you select Infrastructure, devices can communicate with each other and with wired LAN devices
— You must select the same security mode that is used in the wireless LAN access point. If you select
— Edit the security settings for the selected
no., according to instructions from your service provider.
Access points.
settings.
to define the advanced settings or
Options
Automatic
> IPv4.
and Secondary DNS addr.
Access points.
settings.
WLAN security
43
Use login script
No to save the password in your
Normal to send your password encrypted
Advanced settings, and define the following
>
to have the network provide the device IP address.
if required by your service provider
Search for netw..
Public if it is not hidden.
mode.
> Yes.
Use existing settings. To
Back to save the settings
Use existing settings. To