Advanced Internet Access Point Settings For Wireless Lan; Cable Connection; Ip Passthrough; Set Up A Data Cable To Use Ip Passthrough - Nokia E70 User Manual

C o n n e c t i v i t y
Homepage — Enter the Web address of the page you want to display as a home page when you use this access point.
•
The settings available for editing may vary.

Advanced Internet access point settings for wireless LAN

Select Menu Tools Settings
> >
After setting up a basic Internet access point for wireless LAN, select
advanced settings.
IPv4 settings — Enter the device IP and name server addresses for the IPv4 Internet protocol.
•
IPv6 settings — Select or enter the name server addresses for the IPv6 Internet protocol.
•
Ad-hoc channel — If the selected network mode is ad-hoc, select
•
Proxy serv. address — Enter the proxy server address.
•
Proxy port number — Enter the proxy server port number.
•
The settings available for editing may vary. Contact your service provider for more information.

Cable connection

Install the USB data cable driver to your PC before you use a cable connection. You can use the
the USB data cable drivers.
Select Menu Connect.
> >
Using a USB data cable, you can connect your device to a compatible PC . Connect the USB data cable to the bottom of the device.
To change the device type you normally connect to your device with the data cable, press the joystick.
Select from the following:
Ask on connection — Select whether you want to be asked for the device type every time you connect the data cable to your
•
device.
PC Suite — Connect the PC Suite to your device with the data cable, and use your device as a modem.
•
Data transfer — Access and transfer data such as music or image files from your computer using the data cable connection.
•
To use the Data transfer
settings in Nokia PC Suite. Insert a memory card to your device, connect the device to a compatible computer with the USB
data cable, and select Data transfer
device and you can see it as a removable hard drive in your computer. The device will switch into the
selected. End the connection from the PC (for example, from an Unplug or Eject Hardware wizard in Windows) to avoid
damaging the memory card. After you end the connection, the device returns to the profile in which it was before using the
data transfer mode.

IP passthrough

— Select an access point through which to transfer data using the Internet protocol.
•
To save your selection, select Back.
IP passthrough
Select Menu Connect.
> >
The IP passthrough application allows you to obtain a network connection on your device from a compatible PC through a data
cable.

Set up a data cable to use IP passthrough

Use IP passthrough as you use any Internet access point to browse or synchronize remotely. If a wireless network connection
is unavailable, use IP passthrough to access the Internet or a LAN. You cannot use IP passthrough at the same time as Nokia PC
Suite. You cannot activate the modem if you select IP passthrough in cable connection settings.
To prepare for an IP passthrough session, connect a data cable to your device, and select
method. Connect the other end of the data cable to a compatible PC, and wait for the PC to recognize your device.

Access point for IP passthrough

Menu Tools Settings
> > >
To configure IP passthrough basic settings, select
passthrough connection in the

Advanced IP passthrough access point settings

Menu Tools Settings
> > >
To use advanced settings, open an IP passthrough access point, and select
following:
Copyright © 2006 Nokia. All Rights Reserved.
Connection Access
> >
Data cbl..
mode, make sure that you have not selected USB as a connection type in the Manage connections
when the device asks which mode is used. In this mode, your device acts as a mass storage
Data cable Options IP
> >
Connection Access points.
>
Options
Connection name field, and select
Connection Access points.
>
points.
Options
User defined
passthrough.
New access point
>
IP passthrough
Options
44
Advanced settings, and define the following
>
to manually enter a channel number (1-11).
Data transfer
IP passthrough
Use default settings. Enter a name for your IP
>
in the Data bearer field.
Advanced settings
>
without installing
Offline profile if this is
as the connection
and select from the