Setup Screen (Main Menu); Position Setup Screen - JVC RMP-2580U - Remote Controller For Color Domes Instructions Manual

POSITION SETUP SCREEN

This screen is used to preset, correct or delete the camera positions.
No position can be selected unless it has been preset.
Up to 64 positions including the home position can be preset.
Presetting and Correcting Camera Positions
MENU button CAMERA button
SET button
CAMERA CAMERA POSITION POSITION
SETUP SETUP
POWER
ALARM
MENU MENU SET SET
KEY LOCK
LENS LENS CAMERA/POSITION CAMERA/POSITION
1 2 3
SPEED SPEED
4 5 6
CLOSE CLOSE IRIS IRIS OPEN OPEN
FOCUS FOCUS
7 8 9
NEAR NEAR FAR FAR
AF AF
0
WIDE WIDE ZOOM ZOOM TELE TELE CLEAR CLEAR ENTER ENTER
/HOME /HOME
Lens operation buttons ENTER button
Numeric keypad
SETUP
POSITION SETUP..
CAMERA..
CONTROL UNIT..
– POSITION SETUP MODE –
Clearing a Camera Position
POSITION display
CAMERA CAMERA
SETUP SETUP
POWER
ALARM
MENU MENU SET SET
KEY LOCK
LENS LENS CAMERA/POSITION CAMERA/POSITION
1 2
SPEED SPEED
4 5
CLOSE CLOSE IRIS IRIS OPEN OPEN
FOCUS FOCUS
7 8
NEAR NEAR FAR FAR
AF AF
0
WIDE WIDE ZOOM ZOOM TELE TELE CLEAR CLEAR
/HOME /HOME
CLEAR button
POSITION button
RM-P2580 RM-P2580
REMOTE CONTROL UNIT REMOTE CONTROL UNIT
AUTO AUTO F-1 F-1 F-2 F-2 F-3 F-3
PAN/TILT PAN/TILT
CAMERA CAMERA POSI- POSI-
TION TION
OPTION OPTION OPTION OPTION
1 2
AUTO AUTO AUTO AUTO
PAN PAN PATROL PATROL
PAN/TILT control lever
CO1-PO5
RM-P2580 RM-P2580
REMOTE CONTROL UNIT REMOTE CONTROL UNIT
POSITION POSITION
AUTO AUTO F-1 F-2 F-3 F-3
PAN/TILT PAN/TILT
3
CAMERA CAMERA POSI- POSI-
TION TION
6
OPTION OPTION OPTION OPTION
1 2
9 AUTO AUTO AUTO AUTO
PAN PAN PATROL PATROL
ENTER ENTER
5. MENU SCREEN SETUPS
1.
Press and hold the MENU button for about 3 seconds to
display the SETUP screen.
2.
Select POSITION SETUP and press the SET button.
"– POSITION SETUP MODE –" with the currently selected
Camera No. and the Position No. are displayed. ("C01 -
P05" shows the Camera 1, Position 5.)
3.
Select a camera number.
CAMERA button Numeric keys
4.
Select the position number to be preset.
POSITION button Numeric keys
In this case, the camera screen shifts to the pre-regis-
tered POSITION.
5.
Set the image angle.
Set it using the PAN/TILT control lever and the IRIS, ZOOM
and FOCUS control buttons.
6.
Press the SET button for about 1 second.
A short beep indicates that the position has been memo-
rised.
"Invalid operation" is displayed when using the camera which
the position can not be preset, such as fixed camera.
7.
To preset other positions, repeat steps
64 positions including the home position can be preset.
Select the camera ID number and the position number in the
same way as presetting or correcting a position.
1 4
(Steps to of "Presetting and Correcting Camera Positions")
1.
Press and hold the CLEAR button for about 1 second.
A short beep is generated and the position is cleared.
NOTE:
Home position is not clearable.
ENTER button
ENTER button
4 6
to .
27