Applied System (B Mode) - JVC RMP-2580U - Remote Controller For Color Domes Instructions Manual

APPLIED SYSTEM (B MODE)

<The compatible frame switchers are SW-D7000 and SW-D8000.>
This system accepts the connection of up to 16 cameras.
The video is recorded by means of a frame switcher.
When an alarm input is required to the SW-D7000/
SW-D8000, be sure to use the ALM OUTPUT of
the I/O terminal of RM-P2580.
Read the "Instruction Manual" for each piece of
equipment to be connected before performing the
connection.
NOTES
When the +, -, Auto, F1~3 buttons are
pressed quickly and consecutively, it may
happen that the camera display does not
correspond to the video output. If this is the
case, press the buttons slowly and precisely.
The AUTO LED of the RM-P2580 will not light
up, even during AUTO SEQUENCE.
CAMERA 1
AC24V
ID:1
CAMERA 2
AC24V
ID:2
CAMERA 3
AC24V
ID:3
TO
CAMERA
TO CAMERA TO CAMERA
RX RX+ RX RX- TX TX+ TX TX- COM COM 1
POWER
ON OFF
1
AC ` INPUT
1 2 3 4 5 6 7 8
1
ON
Set Pin 1 to "ON" for B Mode.
MASTER MONITOR
1.
2.
3.
4.
5.
6.
7.
8.
9.
10 .
1 2 3 4
MONITOR-A
OUTPUT
VIDEO
INPUT 1 SEREAL-2
DATA I / O DATA I / O
UNIT UNIT CAMERA CAMERA
SERIAL-1 SERIAL-1 SERIAL-2 SERIAL-2
2 3 4 5 6 7 8 COM COM 9/1 9/1 10/2 10/2 11/3 11/3 12/4 12/4 13/5 13/5 14/6 14/6 15/7 15/7 16/8 16/8 COM COM AUTO AUTO ALARM ALARM COM COM SW SW COM COM
VIDEO INPUT VIDEO INPUT
2 3 4 5 6 7 8
MONITOR MONITOR
OUTPUT OUTPUT
1 2
2 3 4 5 6 7 8
VIDEO OUTPUT VIDEO OUTPUT
RM-P2580
MONITOR
OUTPUT 1
V.IN
Setting Procedure
Connect all the equipment.
(All of the cameras must be synchronized)
Set the system mode selection to B Mode, and set the rear DIP SW1
to "ON".
To set a camera ( REF. : Instruction Manual of the camera being
used)
· Match the ID with the VIDEO INPUT number.
· Set to MULTIDOROP and DUPLEX
Using the SERIAL-2 item, set to the frame switcher. ( REF. : page 29)
Set the alarm to the PRIORITY mode for alarm signal input.
Set the " PRIORITY" in the ALARM SCREEN to "ALARM".
( REF. : page 32)
Frame switcher setting
Set the Baud rate to 9600 bps.
Set the SW-D7000/SW-D8000 communications menu of RS232 to
9600 bps.
Set the alarm time to that of RM-P2580.
Adjust the Alarm timeout of the timeout menu inside the alarm latch
menu of SW-D7000/SW-D8000 to the ALARM TIME of RM-P2580.
Preset positions ( REF. : page 27)
Operational setting values can be changed as required.
· P/T SPEED: 8 STEPS ( REF. : page 29)
Check the ALARM INPUT time set value.
· DATA I/O screen: 16ALM IN or 8 ALM IN ( REF. : page 30)
· ALARM screen ( REF. : page 32)
ALARM INPUT TIME setting required for each camera
· TERMINAL item ( REF. : page 31)
5 6 7 8
RS-232C CAM VCR
IN OUTPUT
CAM SW VIDEO
OUT INPUT
REC STOP REC
CHECK
OPERATE
TIMELAPSE VCR
RM-P2580 SERIAL-2 connector
(D-sub 9 pin, female)
Signal name Pin No.
R X D
T X D
G N D
When connecting a frame switcher, be sure to read its
"Instruction manual" before connecting it.
4. CONNECTIONS
MONITOR
V.IN
MONITOR B
OUTPUT
REC
EJECT OPERATE
SW-D7000/SW-D8000 Alarm connector
(D-sub 9 pin, male)
Pin No. Signal name
2 2 R X
3 3 T X
5 5 G N D
21