How To Use Your Tractor; To Set Parking Brake; To Use Throttle Control; To Move Forward And Backward - Craftsman 28913 - LTS 1500 17.5 HP/42" Lawn Tractor Operator's Manual

,LQUIER
tacionamiento,
3AGED).
tenido
ntacto con
accesorio qur
• montado en
3razos de sus-
ldo izquierdo y
Oo
RA
amiento del
alta,
hacia debajo
sontra la des-
del tractor.
lento a su
_nteras a la
eg(_relas con
,,nsi6n a los
tbierta y
de retenci6n.
aci6n al so-
con el resorte
del cable del
lice el collar
n el resorte
I resorte del
)lea-guia y ase-
Dde retenci6n,
ta polea del
,gujero Quadrado
de Motor
an[ero
de Re_enct6n
Lados)
The operation of any tractor can result in foreign objects thrown into
the eyes, which can result in severe eye damage. Always wear safety
glasses or eye shields while operating your tractor or performing any
adjustments or repairs. We recommend a wide vision safety mask over
spectacles or standard safety glasses°
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE
Your tractor is equipped with an operator
presence sensing switch. When engine is
running, any attempt bythe operator to leave
the seatwithout first setting the parking brake
will shut off the engine.
1. Depress clutch/brake pedal all the way
down and hold,
2. Pull parking brake lever up and release
pressure from clutch/brake pedal. Pedal
should remain in brake position, Make
sure parking brake will hold tractor se-
cure.
Throttle/
Choke
Control \\\
"Brake"
Position
Attachment Clutch Lever
"Engaged Position
_nition Key
iaged"
Position
Parking Brake
"Engaged"
Position
Gearshift
Clutch/Brake "Disengaged" Lever
Pedal Position
STOPPING
MOWER BLADES
o To stop mower blades, move attachment
clutch lever to disengaged position.
GROUND DRIVE -
, To stop ground drive, depress clutch!brake
pedal all the way down.
, Move gearshift lever to neutral (N) po-
sition.
ENGINE -
• Move throttle control between half and full
speed (fast) position°
NOTE: Failure to move throttle control
between half and full speed (fast) posi-
tion, before stopping, may cause engine to
"backfire".
, Turn ignition keyto"STOP" position and re-
move key_ Always remove key when leav-
ing tractor to prevent unauthorized use°
• Never use choke to stop engine.
IMPORTANT: Leaving the ignition switch in
any position other than "STOP" will cause
the battery to discharge and go dead.
NOTE: Under certain conditions when tractor
is standing idle with the engine running, hot
engine exhaust gases may cause "brown-
ing" of grass, To eliminate this possibility,
always stop engine when stopping tractor
on grass areas.
_I_CAUTION: Always stop tractor com-
pletely, as described above, before leaving
the operator's position°
TO USE THROTTLE CONTROL
Always operate engine at full speed (fast).
, Operating engine at less than full speed
(fast) reduces engine's operating effi-
ciency.
• Full speed (fast) offers the best mower
performance.
TO MOVE FORWARD AND BACKWARD
The direction and speed of movement is
controlled by the gearshift lever.
1. Start tractor with clutch/brake pedal
depressed and gearshift lever in neutral
(N) position.
2. Move gearshift lever to desired po-
sition_
3_ Slowly release clutch!brake pedalto start
movement.
IMPORTANT: Bring tractor to a complete
stop before shifting or changing gears,
Failure to do so will shorten the useful life
of your transaxle.
T'O ADJUST MOWER CUTTING HEIGHT
The position of the attachment lift lever
determines the cutting height,
• Grasp lift lever.
• Press plunger with thumb and move lever
to desired position.
The cutting height range is approximately
1-1/2 to 4". The heights are measured from
the ground to the blade tip with the engine
not running. These heights are approximate
and may vary depending upon soil condi-
tions, height of grass and types of grass
being mowed,
13