Advertisement
O
i CHECK INSTALLATION
DIMENSIONS
A: Di,_posorHeight
I'
B: Distance from bottom at sink
bowt to centerline of oiscnargg
i
gutter. (Ad_ 1/2" wher_stainless
steel _lnk is used.]
A
C: Distance fromeenterltne of
the discharge outlet to end
of discharge tube,
D: Disposer Width
E: Distance from disposer vertical
contorting to ¢enterttne of
P.lrap connection,
_---|---.I
eol!T=,,!_tlllil3!2 8/8"
a"
F: Centerflne of disposer dlsche.rgeto ¢enterllne lit waste p pO enter ng we
....
(Dimension "F" muet be greater ther_t!4" 1oprevent etendlr_g water]n dlsposer,l ' Indicates B_tchFeedModel
If rgpleclng an exfstlng dfJpOeer skip atleed to IrtllttUollon 8
'_
!
!_this Is eflrwt !_t_e !nail=lib(fen= ¢9_nt!r!uQ w th Irtstru_!lorl 2 ......
DISCONNECT
SINK DRAIN
t, Looeen nul (A) el top ot "P-trap" with pipe wrench (see Figure 2-1),
2, Loosen nut (B) at top of extension pipe. Remove _xtenSion plp_,
3, Loosen nut (C) at base of eink fie.nee. (if nut Is corroded or Ioo tight, _pply
penetrating lubricant,)
4. Push s_nkf_engeup throughsink hole and remove it (_g_ Figure 2-2)
5. Ctean sink flange area of arty putty or ati_er debris,
O
ISASSEMBLE
NEW DISPOSER
MOUNTING ASSEMBLY
t, [near( wrenohe_e (or ecrewdrlver) into one mounting lug _nd hof_ tower mou_{,
{ng rin_ securely with one hand (see Figure 3-1) With your other hand, turn
mounting _.embly
countercfockwma to remove mounting assembly from tower
mounting ring,
2. Turn mounting assembty over (seeFigure 3-2) and loosen three mounttng
screws (A) until you oan I_ccess snap ring (B),
3, Use screwdriver to pry sn_p ring off of sink flange. Moui"tlirlg assembly wit(
now come apart
O
INSTALL FLANGE IN SINK HOLE
t, Roll I/4 pound (4 oz.) of non-hardening plumber's putty [omake 314" thick rope
to ,,eel 8round sink flange,
2, Apply putty evenly around sink hofe (sea Figure 4.1 ).
3, Press sink flange slowty bul firmly into sink drain bole to seat evonty on putty
(see Figure 4.2). Use screwdriver or putty knlN to scrape eli putty from edge
of sink ftole,
Model
.m_o.=
_ _'
ie" _',,,,Z _/f "'_' ......
4"
7 1/4"
5_
O
Do not use plumber's putty on any other dteposer Connection. It
m_y h_rm d_sposer _nd ceu_e property damage,
ATTACH UPPER MOUNTING
ASSEMBLY TO SINK FLANGE
,_
....
_ _
•
_ i ,,,,,,,,,,,,,,,,,,,,.
2*1
2-2
You may wish to place _ weighted o_lect in the stnk to hol_ (he sink flange in piece. (Place 0, towel
under obtect m sink to prever_t scml_hing
) Reference Figure 5-1 for part identtflcallon.
4, Tig_',_en three meurtting
screw-, up to sir_k
u_{it mounting
_9sombly
_ssee_ed lightly
_r_ evenly _,g_inet _tnk.
• Placing _, thick, wide rubber band mound
the sink flange
(_b'Ove the SnSp ring
grOOV_t rrl_y help hold _arts
in place while
tnstalli_g
snap rmg, (Remember
to remove
rubber band alter snap ring le installed,)
1. Working
IrOn under sink, sIip fiber gasket
and
metal backup ring over _ink flange,
2, Holding tiber gasket and b_.ckup rtr_g in piece.
_fip mounli_g
ring over
e!r'_kflange} au il seeI,,i
8galnst i_acku0 ring,
3, With hber gasket,
backup
rmg, and mounting
rlng_ighl to sinkbottom, elid_sn_p ringonto
sink flange un!.il Itpops tr_to groove on flange'.
3-1
3-2
t If you _re repfe, c lng 8n extstlng disposer, go to Instruction 6. I! [his is _ f[rs_time tnst_.t
